VDC off and wheel slip lights on dash....

ban25 · 11-23-2015, 07:38 PM

I checked the DTCs with EcuTek and got the following:

C1109 Nissan - Battery Voltage
ABS actuator and electric unit (control unit) power voltage is too low.

C1107 Nissan - Front Right Sensor 2
- ABS Wheel Sensor not installed currently
- ABS Wheel Sensor rotor or encoder damaged
- ABS Wheel Sensor rotor loose on axle
- Faulty ABS Wheel Sensor
- ABS Wheel Sensor harness is open or shorted
- ABS Wheel Sensor circuit poor electrical connection
- Faulty ABS Control Unit

Smashley · 11-23-2015, 08:19 PM

Quote:

Originally Posted by ban25

Do you have any mods on your car? I'm running EcuTek, though I have not had issues with it until now. I also just got my calipers rebuilt, but again, I had those inspected after the incident.

K&N Typhoon intakes.

ban25 · 11-24-2015, 05:25 PM

Turned out it was my front right wheel bearing that was in need of replacement. You might want to check your's to see if it's the same issue.

1slow370 · 11-24-2015, 06:21 PM

I had this happen once and it was the c clip on the axle stub letting it pop in and out over bumps enough that the sensor was going nuts. $1.80 for a new c clip later and it was gone. wheel bearings and brake fluid levels do it too.

Daishi9000 · 12-01-2015, 05:52 PM

Quote:

Originally Posted by 1slow370

I had this happen once and it was the c clip on the axle stub letting it pop in and out over bumps enough that the sensor was going nuts. $1.80 for a new c clip later and it was gone. wheel bearings and brake fluid levels do it too.

how did you figure that out?

1slow370 · 12-05-2015, 01:37 PM

I caught it at just he right time. It would happen to me when i gave it power in a turn over a bump so i did that in a parking lot and as soon as it came on i stopped the car and got out and checked and i had to push the drivers side stub flange back in about 1\8 inch til it clicked in. Replaced the snap ring and it hasnt popped out since.

1slow370 · 12-06-2015, 02:49 PM

I forgot another thing that can do this is getting an alignment done or taking the steering wheel off and not reseting the 0 position on the steering angle sensor.

Daishi9000 · 12-07-2015, 01:33 AM

OK. thanks. i will check those things.

Quote:

Originally Posted by 1slow370

I forgot another thing that can do this is getting an alignment done or taking the steering wheel off and not reseting the 0 position on the steering angle sensor.

Smashley · 12-13-2015, 01:38 AM

Just changed my wheel hub. All lights are gone!

ban25 · 12-14-2015, 02:23 AM

Quote:

Originally Posted by Smashley

Just changed my wheel hub. All lights are gone!

Awesome! I noticed when we changed the hub on mine that there was a difference between my old 2009 hub and the new part from Nissan. The new hubs appear to be sealed on the inside, probably to keep out dirt and debris. I plan to change the others out as preventative maintenance.

Zrider79 · 02-08-2017, 02:26 PM

Quote:

Originally Posted by pg6speed

I just started having this issue including the brake light about three weeks ago. Subed for info.

This happened to me as well. It's been doing it more often during hard acceleration.

Smashley · 02-09-2017, 08:06 AM

Quote:

Originally Posted by Zrider79

This happened to me as well. It's been doing it more often during hard acceleration.

Top off brake fluid slightly past max level

Zrider79 · 02-19-2017, 06:31 PM

Ok I'll test it out.

Zeetah · 02-27-2017, 02:44 AM

Quote:

Originally Posted by Smashley

Top off brake fluid slightly past max level

finally, this thing was annoying as hell, the red exclamation and slip light going on solid until i restart and it happens every time, it makes me paranoid..

sorry for the newb question but should i check the brake level when the car is off or on? and you said to top it off, but the other 2 guys on the first page of this thread said dont top it off bc when you do a brake change, it will overflow and make a mess?

which brake fluid do we use and whats it called? im just going to buy it from the nissan dealership

Smashley · 02-27-2017, 08:12 AM

Quote:

Originally Posted by Zeetah

finally, this thing was annoying as hell, the red exclamation and slip light going on solid until i restart and it happens every time, it makes me paranoid..

sorry for the newb question but should i check the brake level when the car is off or on? and you said to top it off, but the other 2 guys on the first page of this thread said dont top it off bc when you do a brake change, it will overflow and make a mess?

which brake fluid do we use and whats it called? im just going to buy it from the nissan dealership

Doesn't matter if the car is off or on when checking brake fluid.
Use a DOT 3/4 compatible brake fluid. Doesn't matter what brand. I use Valvoline Synthetic and have no issues.
Don't worry about fluid overflow until you change brake pads and then you can use a syringe to suck some out.

11-23-2015, 07:38 PM	#46 (permalink)
ban25 Enthusiast Member Join Date: Nov 2009 Location: SF, CA Posts: 339 Drives: 17 C7 Z06 M7 Rep Power: 66	I checked the DTCs with EcuTek and got the following: C1109 Nissan - Battery Voltage ABS actuator and electric unit (control unit) power voltage is too low. C1107 Nissan - Front Right Sensor 2 - ABS Wheel Sensor not installed currently - ABS Wheel Sensor rotor or encoder damaged - ABS Wheel Sensor rotor loose on axle - Faulty ABS Wheel Sensor - ABS Wheel Sensor harness is open or shorted - ABS Wheel Sensor circuit poor electrical connection - Faulty ABS Control Unit __________________ 2017 Corvette Z06 7MT \| 1LE \| Stage 3 \| DSCSport

11-24-2015, 05:25 PM	#48 (permalink)
ban25 Enthusiast Member Join Date: Nov 2009 Location: SF, CA Posts: 339 Drives: 17 C7 Z06 M7 Rep Power: 66	Turned out it was my front right wheel bearing that was in need of replacement. You might want to check your's to see if it's the same issue. Smashley likes this. __________________ 2017 Corvette Z06 7MT \| 1LE \| Stage 3 \| DSCSport

11-24-2015, 06:21 PM	#49 (permalink)
1slow370 A True Z Fanatic Join Date: Aug 2009 Location: In the D Posts: 3,732 Drives: v8 74 260z ;) Rep Power: 7251	I had this happen once and it was the c clip on the axle stub letting it pop in and out over bumps enough that the sensor was going nuts. $1.80 for a new c clip later and it was gone. wheel bearings and brake fluid levels do it too. __________________ ANSWER PRICE LIST Answers - - - - - - - - - - - - - - - - $0.75 Answers (requiring thought) - - - - $1.25 Answers (correct) - - - - - - - - - - $12.50

12-05-2015, 01:37 PM	#51 (permalink)
1slow370 A True Z Fanatic Join Date: Aug 2009 Location: In the D Posts: 3,732 Drives: v8 74 260z ;) Rep Power: 7251	I caught it at just he right time. It would happen to me when i gave it power in a turn over a bump so i did that in a parking lot and as soon as it came on i stopped the car and got out and checked and i had to push the drivers side stub flange back in about 1\8 inch til it clicked in. Replaced the snap ring and it hasnt popped out since. __________________ ANSWER PRICE LIST Answers - - - - - - - - - - - - - - - - $0.75 Answers (requiring thought) - - - - $1.25 Answers (correct) - - - - - - - - - - $12.50

12-06-2015, 02:49 PM	#52 (permalink)
1slow370 A True Z Fanatic Join Date: Aug 2009 Location: In the D Posts: 3,732 Drives: v8 74 260z ;) Rep Power: 7251	I forgot another thing that can do this is getting an alignment done or taking the steering wheel off and not reseting the 0 position on the steering angle sensor. __________________ ANSWER PRICE LIST Answers - - - - - - - - - - - - - - - - $0.75 Answers (requiring thought) - - - - $1.25 Answers (correct) - - - - - - - - - - $12.50

12-13-2015, 01:38 AM	#54 (permalink)
Smashley Enthusiast Member Join Date: Aug 2013 Location: Maryland Posts: 347 Drives: mt/sport/tour MB Rep Power: 12	Just changed my wheel hub. All lights are gone! ban25 likes this.

02-19-2017, 06:31 PM	#58 (permalink)
Zrider79 Track Member Join Date: Jan 2011 Location: Pensacola florida Posts: 679 Drives: 2010 Rep Power: 15	Ok I'll test it out. __________________ 2010 Monterey blue roadster Z Touring. Blk interior. g3,fast intentions exhaust,more to come. RIP 05 Silverstone 350z roadster mild N/A build.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
I wish the dash lights on the 40th were red not orange	LafitteZ	40th Anniversary 370Z	7	09-04-2012 12:48 AM
[FOR SALE] Pioneer AVH-P4200DVD, PAC steering wheel control, Metra dash kit, 6.5 door spacers	Danny3.7	Parts for sale (Private Classifieds)	6	08-06-2011 07:18 AM
ABS+traction control+slip lights all on please help	zuperman 370	Wheels & Tires	16	06-15-2011 01:07 PM
Steering wheel lights not working	egurusinghe	Australia/New Zealand	1	05-28-2011 10:04 AM
Parking lights, Signal lights, license plate light opinion	wdkwang	Exterior & Interior	0	03-19-2011 12:25 AM