STILLEN lightweight crank pulley

semtex · 06-07-2009, 05:02 PM

It should also be mentioned that if you intend to install a supercharger in the future, you don't want an UD pulley, as superchargers are belt driven. Although you could swap it back out if you install a supercharger down the road.

black09Z · 06-08-2009, 12:20 PM

no i meant as like compared to the light weight pulley

semtex · 06-08-2009, 12:30 PM

Those ARE the cons compared to the lightweight pulley.

wstar · 06-08-2009, 01:41 PM

Quote:

Originally Posted by imag

One other con that should be mentioned - you won't get as much current to your battery through the alternator (underdrive means lower belt speed). This is probably only an issue if you have a high-current audio system.

This is only true at idle though. Once you bring the revs up to driving speed the alternator is still getting more RPMs than it needs (which is why they have clutches) to maintain the proper output. Even at idle, I don't think you're actively draining your battery or anything, just not charging it as fast

Perhaps if you have a truly monster audio system it might be a concern. I don't, and I haven't had any issues with the UD pulley as far as voltage is concerned though, and I've had mine on for quite a while now. I also switched to a tiny PC680 battery mounted in the trunk via a long cable run. Even then, I still haven't had any problems starting the car, or any other electrical issues.

Quote:

I assume the lower speed to the power steering pump doesn't make any difference...

Right, the other two minor points for potential concern for the UD pulley are the AC and the Power Steering. I haven't had any issues with either. The change to the power steering isn't really noticeable, and again even if it were, it would only be at low rpm rolling around a parking lot. AC is fine too, still blasting ice cold air in the Houston heat.

In short, there really are no cons, unless maybe you have very demanding electrical needs at idle.

Crash · 06-08-2009, 09:41 PM

^^ So no vacuuming the house on the car's power parked in the driveway?

bmarcinczyk14 · 08-02-2009, 10:49 PM

quick question, is it possible to get both the underdrive pulley and lightweight pulley installed on the car?

RCZ · 08-02-2009, 11:34 PM

by virtue of being underdriven, the underdrive pulley is smaller and lighter than the normal lightweight pulley. So no, they replace the same part and the underdriven one is smaller and lighter.

FairLadyZee · 08-01-2011, 10:33 PM

Got my stillen lightweight crank pulley put on and was wondering if n e one would kno why the engine makes noise now when it down shifts at times goin downhill and a little bit when i get high rpm's??...its kinda like a hissing sound..sounds like the belt but its suppose 2 use the stock still..thanks

06-07-2009, 05:02 PM	#91 (permalink)
semtex A True Z Fanatic Join Date: Jan 2009 Location: Behind enemy lines Age: 54 Posts: 5,995 Drives: People to drink Rep Power: 33	It should also be mentioned that if you intend to install a supercharger in the future, you don't want an UD pulley, as superchargers are belt driven. Although you could swap it back out if you install a supercharger down the road. __________________ "There are no small accidents on this circuit." -- Ayrton Senna 316.8whp & 248 ft/lbs (Dyno Dynamics) \| 319whp & 256 ft/lbs (DynoJet) (04/23/10) Stillen G3 CAI, CBE, Pulley / F.I. LTH / GTSpec Ladder Brace / Setrab Oil Cooler / UpRev-tuned by Forged Perf.

06-08-2009, 12:30 PM	#93 (permalink)
semtex A True Z Fanatic Join Date: Jan 2009 Location: Behind enemy lines Age: 54 Posts: 5,995 Drives: People to drink Rep Power: 33	Those ARE the cons compared to the lightweight pulley. __________________ "There are no small accidents on this circuit." -- Ayrton Senna 316.8whp & 248 ft/lbs (Dyno Dynamics) \| 319whp & 256 ft/lbs (DynoJet) (04/23/10) Stillen G3 CAI, CBE, Pulley / F.I. LTH / GTSpec Ladder Brace / Setrab Oil Cooler / UpRev-tuned by Forged Perf.

06-08-2009, 09:41 PM	#95 (permalink)
Crash A True Z Fanatic Join Date: Dec 2008 Location: Los Angeles Posts: 1,853 Drives: 02 Corvette Z06 Rep Power: 590	^^ So no vacuuming the house on the car's power parked in the driveway? __________________ 2002 Corvette Z06 - Totaled 2003 Corvette Z06 50th Anniversary

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Lightweight flywheels and SyncroRev Match	semtex	Engine & Drivetrain	19	01-25-2015 12:55 PM
Stillen Headers on 370z	Funky370z	Intake/Exhaust	72	04-07-2009 11:38 AM
Welcome STILLEN	AK370Z	STILLEN	10	02-03-2009 03:19 PM
Stillen Intake for VQ37VHR	vdcoff	Intake/Exhaust	7	01-25-2009 04:27 PM
Nissan 370Z on Display @ Stillen on 11/18	Slidefox	Nissan 370Z General Discussions	4	11-13-2008 08:41 PM

06-08-2009, 12:20 PM	#92 (permalink)
black09Z Base Member Join Date: Mar 2009 Location: killeen tx Posts: 202 Drives: black 09 370Z 6spd Rep Power: 16	no i meant as like compared to the light weight pulley

08-02-2009, 10:49 PM	#96 (permalink)
bmarcinczyk14 Track Member Join Date: Jul 2009 Location: Chicago Posts: 505 Drives: 2010 370z 6spd Sport Rep Power: 17	quick question, is it possible to get both the underdrive pulley and lightweight pulley installed on the car?

08-02-2009, 11:34 PM	#97 (permalink)
RCZ A True Z Fanatic Join Date: Nov 2008 Location: Miami Posts: 6,403 Drives: '09 370Z Rep Power: 1119	by virtue of being underdriven, the underdrive pulley is smaller and lighter than the normal lightweight pulley. So no, they replace the same part and the underdriven one is smaller and lighter.

08-01-2011, 10:33 PM	#98 (permalink)
FairLadyZee Enthusiast Member Join Date: Jun 2011 Location: Connecticut Posts: 281 Drives: 09'-370z-Silver-SP Rep Power: 14	Got my stillen lightweight crank pulley put on and was wondering if n e one would kno why the engine makes noise now when it down shifts at times goin downhill and a little bit when i get high rpm's??...its kinda like a hissing sound..sounds like the belt but its suppose 2 use the stock still..thanks