What oil pressure gage is everyone using?

m3clubracer · 10-04-2023, 04:46 PM

What oil pressure gage, sending unit, and sandwich plate is everyone using? I need recommendations. Buying tomorrow.

Averying · 10-04-2023, 09:52 PM

Pretty sure I have AEM 30-4407. It is tee’d into one of the hoses for my oil cooler.

Sent from my iPhone using Tapatalk

Rusty · 10-04-2023, 10:57 PM

Oil pressure gauge. SpeedHut 0-150 psi. Any gauge you get HAS to read over 125 psi. Cold starts and high rpm will push the pressure over 110 psi.

https://speedhut.com/gauge-applicati...psi-w-warning/

m3clubracer · 10-05-2023, 09:56 AM

Would it be cheaper to get an old google phone and use Torque/pro? I hear the sending unit near the oil filter is a switch not a gage??? Will Torque read actual real time pressure on a VQ? I am using for diagnostics only not full time, just street, not track.

Averying · 10-05-2023, 01:33 PM

Quote:

Originally Posted by m3clubracer

Would it be cheaper to get an old google phone and use Torque/pro? I hear the sending unit near the oil filter is a switch not a gage??? Will Torque read actual real time pressure on a VQ? I am using for diagnostics only not full time, just street, not track.

Correct, the sending unit is a switch not a gauge. It’s worth the time to install an in cabin gauge. I like the security of being able to watch real time oil pressure.

Sent from my iPhone using Tapatalk

m3clubracer · 10-05-2023, 01:37 PM

Quote:

Originally Posted by Averying

Correct, the sending unit is a switch not a gauge. It’s worth the time to install an in cabin gauge. I like the security of being able to watch real time oil pressure.

Sent from my iPhone using Tapatalk

It's just a lot of trouble for once and a while.

BGTV8 · 10-05-2023, 04:33 PM

By the time you react to an oil-pressure gauge, your engine will either suffer bearing damage or be toast.

In my early days I always had a lo-pressure light using a BMC Mini (remember those) oil pressure warning switch (because they were a commodity back in the day and triggered at 36psi) but now I have a Motec CDL dash, I have an alarm set in the dash that lights up all the shift lights in red and the ECU is set to read oil pressure every 10 milli-seconds which is every rotation of the engine at 6000rpm. If the ECU sees 2 consecutive readings at 36psi or below and rpms are above 2500rpm, then it implements a 2500rpm rev limit and wont permit more than 15% tps as it can react quicker than I can - given my visual reaction time is about 0.25 of a second (and believe me, I practice it), that is still 25 rotations of the crank before I'll notice it - ECU management is better (MOTEC M150)

For bling, go for it, to save an engine, not sure it will be much help

Averying · 10-05-2023, 09:28 PM

Quote:

Originally Posted by BGTV8

By the time you react to an oil-pressure gauge, your engine will either suffer bearing damage or be toast.

In my early days I always had a lo-pressure light using a BMC Mini (remember those) oil pressure warning switch (because they were a commodity back in the day and triggered at 36psi) but now I have a Motec CDL dash, I have an alarm set in the dash that lights up all the shift lights in red and the ECU is set to read oil pressure every 10 milli-seconds which is every rotation of the engine at 6000rpm. If the ECU sees 2 consecutive readings at 36psi or below and rpms are above 2500rpm, then it implements a 2500rpm rev limit and wont permit more than 15% tps as it can react quicker than I can - given my visual reaction time is about 0.25 of a second (and believe me, I practice it), that is still 25 rotations of the crank before I'll notice it - ECU management is better (MOTEC M150)

For bling, go for it, to save an engine, not sure it will be much help

For me it’s good to monitor gallery gasket health since I have an ‘09 and haven’t replaced the gaskets. Too bad that there’s no way to have an ECUTEK tune react to low oil pressure like you’re describing on the Motec.

Sent from my iPhone using Tapatalk

Spooler · 10-05-2023, 10:58 PM

There are many good reasons to go to a standalone. The only negative is the cost. It's not cheap.

2011 Nismo#91 · 10-06-2023, 06:42 AM

Prosport EVO.
DIY: Oil Pressure Gauge

MotorvateDIY · 10-06-2023, 09:26 AM

Quote:

Originally Posted by Averying

Too bad that there’s no way to have an ECUTEK tune react to low oil pressure like you’re describing on the Motec.

EcuTek is going to be adding CAN bus sensor input to the VQ37 platform.
This will allow oil pressure monitoring and RPM reduction to protect the engine. It will also allow ethanol content, fuel pressure or almost anything else as an input.

I have designed/built a CAN bus module and will be testing it on my car with Eugene once this update is released.

Averying · 10-06-2023, 10:16 AM

Quote:

Originally Posted by MotorvateDIY

EcuTek is going to be adding CAN bus sensor input to the VQ37 platform.
This will allow oil pressure monitoring and RPM reduction to protect the engine. It will also allow ethanol content, fuel pressure or almost anything else as an input.

I have designed/built a CAN bus module and will be testing it on my car with Eugene once this update is released.

Wow this is exactly what I wanted to hear!!! (Did I miss this in your thread? Whoops…)

That will be a must add for my car when it’s released.

Sent from my iPhone using Tapatalk

Rusty · 10-06-2023, 02:50 PM

The SpeedHut gauge has a low pressure and a high pressure warning that you can set to any psi you like. My low pressure warning is set at 20 psi. I have the high pressure set at 130 psi.

abm89 · 10-06-2023, 02:52 PM

Haltech iC-7 haha. I had a VLS gauge and just programmed the voltages into the haltech dash.

MotorvateDIY · 10-06-2023, 03:11 PM

Quote:

Originally Posted by Averying

Wow this is exactly what I wanted to hear!!! (Did I miss this in your thread? Whoops…)

That will be a must add for my car when it’s released.

Other than this post, I haven't mentioned it.
Normally, I like to have a running prototype before I say anything.

However, since I was getting some other circuit boards made, (GTR Converter!!!), I added a board that does "analog in" (pressure & temp) to CAN bus.

Once I'm further along with the local testing of the "GTR gauges", I'll assemble, program and test it on the bench.

10-04-2023, 04:46 PM	#1 (permalink)
m3clubracer Base Member Join Date: Nov 2015 Location: Charlotte Posts: 9 Drives: G37x (also F80M3) Rep Power: 10	What oil pressure gage is everyone using? What oil pressure gage, sending unit, and sandwich plate is everyone using? I need recommendations. Buying tomorrow.

10-04-2023, 09:52 PM	#2 (permalink)
Averying Enthusiast Member Join Date: May 2018 Location: Rhode Island Posts: 478 Drives: '09 370Z, '03 G35 Rep Power: 14419	Pretty sure I have AEM 30-4407. It is tee’d into one of the hoses for my oil cooler. Sent from my iPhone using Tapatalk m3clubracer likes this. __________________ 2009 Sport Touring \| Platinum Graphite \| GTM Stage 1 Supercharger \| BC BR Coilovers \| Hotchkis Swaybar \| Z1 FUCAs \| AME TM-02 Wheels \| Z1 2-piece Front Rotors \| Z1 Clutch & Flywheel \| Invidia Gemini Catback \| GTM Resonated Test Pipes

10-04-2023, 10:57 PM	#3 (permalink)
Rusty Ronin Samurai - Assassin Join Date: Dec 2011 Location: Fayettenam,Pennsyltucky Age: 68 Posts: 35,218 Drives: 2011 Nismo GM 6M Rep Power: 2684438	Oil pressure gauge. SpeedHut 0-150 psi. Any gauge you get HAS to read over 125 psi. Cold starts and high rpm will push the pressure over 110 psi. https://speedhut.com/gauge-applicati...psi-w-warning/ NecioVato, m3clubracer and redondoaveb like this. __________________ 浪人 - 殺し屋 "The Difficult Anytime, The Impossible By Appointment Only" http://www.the370z.com/members-370z-...o-journal.html

10-06-2023, 06:42 AM	#10 (permalink)
2011 Nismo#91 A True Z Fanatic Join Date: Mar 2011 Location: NJ Posts: 2,402 Drives: slowly Rep Power: 40569	Prosport EVO. DIY: Oil Pressure Gauge m3clubracer likes this. __________________ GTR TT 493Whp/431lbft, Ecutek, Southbend 6puck,Quaife, RPM RollBar 4Point, R888R, JRZ RSPro F(10R/10C) R(10R/6C) 1000f500r inlbs+150inlbs Tender, SPL everywhere.Full Specs

10-06-2023, 02:50 PM	#13 (permalink)
Rusty Ronin Samurai - Assassin Join Date: Dec 2011 Location: Fayettenam,Pennsyltucky Age: 68 Posts: 35,218 Drives: 2011 Nismo GM 6M Rep Power: 2684438	The SpeedHut gauge has a low pressure and a high pressure warning that you can set to any psi you like. My low pressure warning is set at 20 psi. I have the high pressure set at 130 psi. __________________ 浪人 - 殺し屋 "The Difficult Anytime, The Impossible By Appointment Only" http://www.the370z.com/members-370z-...o-journal.html

10-05-2023, 09:56 AM	#4 (permalink)
m3clubracer Base Member Join Date: Nov 2015 Location: Charlotte Posts: 9 Drives: G37x (also F80M3) Rep Power: 10	Would it be cheaper to get an old google phone and use Torque/pro? I hear the sending unit near the oil filter is a switch not a gage??? Will Torque read actual real time pressure on a VQ? I am using for diagnostics only not full time, just street, not track.

10-05-2023, 04:33 PM	#7 (permalink)
BGTV8 A True Z Fanatic Join Date: Dec 2009 Location: 03350 Australia Posts: 1,514 Drives: 09 Nissan 370Z M6 Rep Power: 39973	By the time you react to an oil-pressure gauge, your engine will either suffer bearing damage or be toast. In my early days I always had a lo-pressure light using a BMC Mini (remember those) oil pressure warning switch (because they were a commodity back in the day and triggered at 36psi) but now I have a Motec CDL dash, I have an alarm set in the dash that lights up all the shift lights in red and the ECU is set to read oil pressure every 10 milli-seconds which is every rotation of the engine at 6000rpm. If the ECU sees 2 consecutive readings at 36psi or below and rpms are above 2500rpm, then it implements a 2500rpm rev limit and wont permit more than 15% tps as it can react quicker than I can - given my visual reaction time is about 0.25 of a second (and believe me, I practice it), that is still 25 rotations of the crank before I'll notice it - ECU management is better (MOTEC M150) For bling, go for it, to save an engine, not sure it will be much help

10-05-2023, 10:58 PM	#9 (permalink)
Spooler A True Z Fanatic Join Date: Jun 2014 Location: Ga Posts: 13,834 Drives: 2013 Nismo 370z Rep Power: 2684392	There are many good reasons to go to a standalone. The only negative is the cost. It's not cheap.

10-06-2023, 02:52 PM	#14 (permalink)
abm89 A True Z Fanatic Join Date: Feb 2013 Location: Austin, Texas Posts: 1,386 Drives: 11 370Z \| 24 EL450 Rep Power: 64763	Haltech iC-7 haha. I had a VLS gauge and just programmed the voltages into the haltech dash. __________________ Complete Parts List: https://github.com/abm89/ztouge-build Last edited by abm89; 10-06-2023 at 02:55 PM.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Fuel Pressure Graph & WOT Pressure Drop	MotorvateDIY	Engine & Drivetrain	2	04-26-2022 05:22 PM
Fuel Gage stuck .. indicating near full	sancle	Exterior & Interior	3	06-25-2013 04:22 PM
Fuel Temperature Gage Cover 2013 Available?	cinellipro	Exterior & Interior	28	02-24-2012 10:31 AM
Where Is The Oil Gage ??	MY1STZ	Engine & Drivetrain	2	09-07-2010 03:22 AM
Fuel gage indicator	fxroar	Exterior & Interior	12	01-10-2010 12:05 PM