Best motor builder or switch platforms?

shadow85 · 09-30-2021, 08:22 PM

I have been fancying the idea of building the motor and 7AT trans for a reliable 800-900whp weekend warrior.

Who is the best, most reliable and trusted motor builder for the VQ37. I know there are a few good ones around nowadays, Dynosty, IPP, SOHO just to name a few.

Is there a general consensus on which would be my best bet for the strongest builder. I would need for them to be able to supply the core, build and ship to Australia if possible. Or send the rebuild kit and have a local shop to do the build on my core. Same with the transmission, but still not sure which builder to chose for that, IPT or Pure Transmission USA?

Either the above, or sell my current Z and fund towards a 2019 Supra, or 2018 Audi TTRS. They are the options I want to lay down, not interested in any other cars, well at least within my budget.

Please give me any opinions or advice about this request? Thanks.

jchammond · 09-30-2021, 08:29 PM

I have Mazworx Built Engine & IPT built trans

I like the Darton sleeves

shadow85 · 09-30-2021, 09:11 PM

Quote:

Originally Posted by jchammond

I have Mazworx Built Engine & IPT built trans

I like the Darton sleeves

Interesting.

Can you share what power/tq you are making, and is it all holding up alrite.

After the motor/trans build, was there alot of teething issues with them, and or major breakdowns that required further re-building?

I just want to know, if I should continue to bother on this platform, or sell it for something like the other cars in my OP.

redondoaveb · 09-30-2021, 10:03 PM

Quote:

Originally Posted by shadow85

Interesting.

Can you share what power/tq you are making, and is it all holding up alrite.

After the motor/trans build, was there alot of teething issues with them, and or major breakdowns that required further re-building?

I just want to know, if I should continue to bother on this platform, or sell it for something like the other cars in my OP.

His car's not complete yet but here a thread on one that's completed. He's making a little over 1000 whp. He's running a manual trans though with a Mazworx motor

Fast Intentions Stage 2 TT build by MA-Motorsports.

shadow85 · 09-30-2021, 11:03 PM

ok gona read later, thanks.

But wow, he started that thread in 2018. 3 yrs, and still not finished?

I am unsure if I can wait long periods of time again without the car. I have already done that on numerous occasions.

More of a reason why I want to switch platforms and go for a stage 3 build + tune on either the B58 or TTRS platform.

But then again, I have already spent tons of coin on my Z and should keep it, and I think it still looks very good! Ahh decisions, decisions.

redondoaveb · 09-30-2021, 11:17 PM

Quote:

Originally Posted by shadow85

ok gona read later, thanks.

But wow, he started that thread in 2018. 3 yrs, and still not finished?

I am unsure if I can wait long periods of time again without the car. I have already done that on numerous occasions.

More of a reason why I want to switch platforms and go for a stage 3 build + tune on either the B58 or TTRS platform.

But then again, I have already spent tons of coin on my Z and should keep it, and I think it still looks very good! Ahh decisions, decisions.

The 1000 whp car is complete. jchammonds car isn't complete yet. Your car doesn't need to be down too long if you're not using your existing motor for your new build

shadow85 · 09-30-2021, 11:48 PM

Ok understood.

Yeah, I was thinking about getting a side motor.

But in all honesty, I don't need to aim for 1000whp. I rekon a reliable 800whp would be plenty enough. I just don't want to deal with heaps of head aches, and or failures though lol i feel like i have done that on my current build for plenty of years.

That's why I am willing to pay the coin for the best work and install, and pray its not going to be tons of ongoing issues.

But then I guess, when venturing into this kind of territory, nothing is guaranteed rite?

redondoaveb · 10-01-2021, 12:09 AM

Quote:

Originally Posted by shadow85

Ok understood.

Yeah, I was thinking about getting a side motor.

But in all honesty, I don't need to aim for 1000whp. I rekon a reliable 800whp would be plenty enough. I just don't want to deal with heaps of head aches, and or failures though lol i feel like i have done that on my current build for plenty of years.

That's why I am willing to pay the coin for the best work and install, and pray its not going to be tons of ongoing issues.

But then I guess, when venturing into this kind of territory, nothing is guaranteed rite?

The 2 best out there are Mazworx and SOHO but like you said, nothing is guaranteed. Jchammond or Spooler are better suited to answer your questions though, I just follow their builds

jchammond · 10-01-2021, 04:43 AM

Shadow85,
Planning to be up & running before 2022 gets here…but I’ve been a bit slacking lately with my wrench time (personal reasons lol)
The Mazworx engine has the Darton mid sleeves properly installed with their knowledgeable staff + many years building Race Engine’s.
Pro H-Beam Carillon rods, Forged CP Pistons (96mm 10:1 CR), King Race Bearings (Rod,Main/Thrust), ARP Main/Head Studs, CNC Port/Polish heads, Chamber Polish, Bronze Guides, +1 mm Supertech valves (Inconel exhaust), JWT C2 exhaust cams, ATI Damper, engine spun & primed w/30wt.break in oil, oil pressure checked.
Phone or email Mark@Mazworx.
Elmo has helped a few people source engine’s to them for others.
John at IPT has developed a good rep with boosted VQ’s in front of his built 7A/T’s.
I’m gonna limit my high boost initially at 24# though engine is rated up to 40# boost.

FL 4Motion · 10-01-2021, 09:26 AM

Quote:

Originally Posted by shadow85

I have been fancying the idea of building the motor and 7AT trans for a reliable 800-900whp weekend warrior.

Who is the best, most reliable and trusted motor builder for the VQ37. I know there are a few good ones around nowadays, Dynosty, IPP, SOHO just to name a few.

Is there a general consensus on which would be my best bet for the strongest builder. I would need for them to be able to supply the core, build and ship to Australia if possible. Or send the rebuild kit and have a local shop to do the build on my core. Same with the transmission, but still not sure which builder to chose for that, IPT or Pure Transmission USA?

Either the above, or sell my current Z and fund towards a 2019 Supra, or 2018 Audi TTRS. They are the options I want to lay down, not interested in any other cars, well at least within my budget.

Please give me any opinions or advice about this request? Thanks.

If you really like the z, then keep it and go built motor/trans plus all the additional sh1t like cooling, brakes, rear diff, axles etc.

But the other two platforms are gonna be easier to make faster. The ttrs is a monster, I speak from experience.

Oh, if you’re gonna build a reliable 800-900 whp motor and trans, that’s essentially the same build as a 1000 whp build as far as requirements to be rock solid.

Quote:

Originally Posted by shadow85

ok gona read later, thanks.

But wow, he started that thread in 2018. 3 yrs, and still not finished?

I am unsure if I can wait long periods of time again without the car. I have already done that on numerous occasions.

More of a reason why I want to switch platforms and go for a stage 3 build + tune on either the B58 or TTRS platform.

But then again, I have already spent tons of coin on my Z and should keep it, and I think it still looks very good! Ahh decisions, decisions.

A stage III build with a hybrid turbo setup on a ttrs will run 9’s, with a full BT swap, iirc they’re in the 8’s now. (E85).

The stock drivetrain will live under stage III hybrid turbo setup providing you aren’t reckless (700-750 hp w/ e85).

Instead of focusing on a whp #. Ask yourself how fast do you want to go? And how deep are your pockets? It will be easier to go xxx speed/time in a ttrs vs a built z.

If you’re gonna dump $$ into a car, (make no mistake, a stage III built ttrs is still a big build albeit much less than the z build), you really want to be sure you’re committed to a long term relationship forsaking all others etc. otherwise, you’ll end up selling at pennies on the dollar and lose your shirt.

Spooler · 10-01-2021, 10:17 AM

Do you really want to go down this road. You struggled with 600whp or less from what I remember. 700whp is still not that bad with the proper mods. 800whp it is starting to get crazy. 900whp and up is off the chart. If you have 6 figures laying around, go for it.

JARblue · 10-01-2021, 10:40 AM

Quote:

Originally Posted by shadow85

But wow, he started that thread in 2018. 3 yrs, and still not finished?

I am unsure if I can wait long periods of time again without the car. I have already done that on numerous occasions.

Quote:

Originally Posted by Spooler

Do you really want to go down this road. You struggled with 600whp or less from what I remember. 700whp is still not that bad with the proper mods. 800whp it is starting to get crazy. 900whp and up is off the chart. If you have 6 figures laying around, go for it.

He's a glutton for punishment

cv129 · 10-01-2021, 03:53 PM

Quote:

Originally Posted by JARblue

He's a glutton for punishment

He's trying to keep the forum alive by punishing himself, creating juicy contents in doing so.

Tractionless · 10-01-2021, 10:10 PM

Quote:

Originally Posted by shadow85

I have been fancying the idea of building the motor and 7AT trans for a reliable 800-900whp weekend warrior.

Like to see ya incorporate the VR trans. under the Z since!!

VR transmission swap

Hammond,
Did you look into this by chance?

Mr.Squeeze · 10-01-2021, 11:14 PM

Quote:

Originally Posted by shadow85

ok gona read later, thanks.

But wow, he started that thread in 2018. 3 yrs, and still not finished?

I am unsure if I can wait long periods of time again without the car. I have already done that on numerous occasions.

More of a reason why I want to switch platforms and go for a stage 3 build + tune on either the B58 or TTRS platform.

But then again, I have already spent tons of coin on my Z and should keep it, and I think it still looks very good! Ahh decisions, decisions.

To minimize down time get another engine or at least a short block to cut down on down time. The thing with building a car or any car is nothing is going to go perfect even with the best builder or shop. You will have delays something will break there will be some type setback. People always think just pay shop slap it together that's just not reality for a lot of builds.

The information has been given to you Soho Motorsports or Mazworx are the best right now.

09-30-2021, 08:22 PM	#1 (permalink)
shadow85 Track Member Join Date: Jul 2015 Location: South Australia, Austra Posts: 918 Drives: 15' 370Z A/T AMM TT Rep Power: 25	Best motor builder or switch platforms? I have been fancying the idea of building the motor and 7AT trans for a reliable 800-900whp weekend warrior. Who is the best, most reliable and trusted motor builder for the VQ37. I know there are a few good ones around nowadays, Dynosty, IPP, SOHO just to name a few. Is there a general consensus on which would be my best bet for the strongest builder. I would need for them to be able to supply the core, build and ship to Australia if possible. Or send the rebuild kit and have a local shop to do the build on my core. Same with the transmission, but still not sure which builder to chose for that, IPT or Pure Transmission USA? Either the above, or sell my current Z and fund towards a 2019 Supra, or 2018 Audi TTRS. They are the options I want to lay down, not interested in any other cars, well at least within my budget. Please give me any opinions or advice about this request? Thanks. jchammond likes this.

09-30-2021, 08:29 PM	#2 (permalink)
jchammond A True Z Fanatic Join Date: Nov 2014 Location: South Carolina Age: 58 Posts: 15,204 Drives: 13’ 370Z TS 7A/T Rep Power: 2684394	I have Mazworx Built Engine & IPT built trans I like the Darton sleeves Mr.Squeeze, JARblue, Hotrodz and 1 others like this. __________________ MazWorx built long block \| FI-TT-100 Stage 2.75 \| IPT built 7A/T http://www.the370z.com/members-370z-...s-musings.html

09-30-2021, 11:03 PM	#5 (permalink)
shadow85 Track Member Join Date: Jul 2015 Location: South Australia, Austra Posts: 918 Drives: 15' 370Z A/T AMM TT Rep Power: 25	ok gona read later, thanks. But wow, he started that thread in 2018. 3 yrs, and still not finished? I am unsure if I can wait long periods of time again without the car. I have already done that on numerous occasions. More of a reason why I want to switch platforms and go for a stage 3 build + tune on either the B58 or TTRS platform. But then again, I have already spent tons of coin on my Z and should keep it, and I think it still looks very good! Ahh decisions, decisions. FL 4Motion likes this.

10-01-2021, 04:43 AM	#9 (permalink)
jchammond A True Z Fanatic Join Date: Nov 2014 Location: South Carolina Age: 58 Posts: 15,204 Drives: 13’ 370Z TS 7A/T Rep Power: 2684394	Shadow85, Planning to be up & running before 2022 gets here…but I’ve been a bit slacking lately with my wrench time (personal reasons lol) The Mazworx engine has the Darton mid sleeves properly installed with their knowledgeable staff + many years building Race Engine’s. Pro H-Beam Carillon rods, Forged CP Pistons (96mm 10:1 CR), King Race Bearings (Rod,Main/Thrust), ARP Main/Head Studs, CNC Port/Polish heads, Chamber Polish, Bronze Guides, +1 mm Supertech valves (Inconel exhaust), JWT C2 exhaust cams, ATI Damper, engine spun & primed w/30wt.break in oil, oil pressure checked. Phone or email Mark@Mazworx. Elmo has helped a few people source engine’s to them for others. John at IPT has developed a good rep with boosted VQ’s in front of his built 7A/T’s. I’m gonna limit my high boost initially at 24# though engine is rated up to 40# boost. Rusty and shadow85 like this. __________________ MazWorx built long block \| FI-TT-100 Stage 2.75 \| IPT built 7A/T http://www.the370z.com/members-370z-...s-musings.html

10-01-2021, 10:17 AM	#11 (permalink)
Spooler A True Z Fanatic Join Date: Jun 2014 Location: Ga Posts: 13,792 Drives: 2013 Nismo 370z Rep Power: 2684392	Do you really want to go down this road. You struggled with 600whp or less from what I remember. 700whp is still not that bad with the proper mods. 800whp it is starting to get crazy. 900whp and up is off the chart. If you have 6 figures laying around, go for it. FL 4Motion, Mr.Squeeze, 2011 Nismo#91 and 4 others like this.

09-30-2021, 11:48 PM	#7 (permalink)
shadow85 Track Member Join Date: Jul 2015 Location: South Australia, Austra Posts: 918 Drives: 15' 370Z A/T AMM TT Rep Power: 25	Ok understood. Yeah, I was thinking about getting a side motor. But in all honesty, I don't need to aim for 1000whp. I rekon a reliable 800whp would be plenty enough. I just don't want to deal with heaps of head aches, and or failures though lol i feel like i have done that on my current build for plenty of years. That's why I am willing to pay the coin for the best work and install, and pray its not going to be tons of ongoing issues. But then I guess, when venturing into this kind of territory, nothing is guaranteed rite?

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Aerial Photography Platforms	osbornsm	Photography	43	05-10-2019 04:24 PM
AAM Competition R&D opportunity for AWD G Platforms!!!	michaeld@aamc	Drivetrain/Engine	35	04-15-2016 11:40 AM
New to the 370z not new to the Z car platforms	Chasingstatus	New 370Z Owner	24	05-31-2014 07:09 AM
GTR - Nissan trains 5th builder. GTR nismo to be 2sec flat to 60?	UNKNOWN_370	Other Vehicles	9	10-09-2013 01:24 PM
VQ engigne builder	Z eliminator	Canada	9	10-10-2012 10:18 AM