Looking for info on talented VHR builders.

FL 4Motion · 08-03-2021, 01:04 AM

Quote:

Originally Posted by redondoaveb

You could also do what I'm doing. Just keep a spare low miles long block as a backup

That, and a rainy day fund in cash of at least the cost of a built motor if going that route or a stock motor if staying that route.

FL 4Motion · 08-03-2021, 01:06 AM

Quote:

Originally Posted by Spooler

All the LS swaps I have seen were not that great.

What about gbrettin’s…oh wait it’s still technically vapor ware until it moves under its own power right?

oldskoolchuk · 08-03-2021, 01:15 AM

Quote:

Originally Posted by FL 4Motion

Ok, swapping in a new to you stock long block and then using your old motor to build up w/o going thru as much downtime is a good idea. Also, then when you swap again, you’ll have a spare long block on deck just in case. Even a fully built motor done by the best shop around and tuned by the best tuner etc could still easily go boom just bc at those power levels, 800+ whp, there’s just no guarantees on anything. Be prepared to be chasing down little gremlins on a regular basis too, that’s part of the game at that level.

You’ll see in spooler’s thread, but your going to need to address your 6mt at some point, I’m assuming you’ve got a mt cause the at won’t cut it at that level afaik. You should look into Phunk’s thread about swapping in a bmw dct so you can put the power done better and w/o trans breakage. He’s CJ Motorsports btw, great guy and great company.

Alright, so you want to be hot sh1t at the local drags and do it in a 370z platform.

First, I’m going to assume all this will be taking place at the local drag strip.

Two, as others have already said, you need to grow your skills into the car. Master 500whp, then 550, then 600, etc. experiment with various tire setups, work on your 60 ft, work on your shifting, car control down the track. Work on improving not just your times but also your et’s. Get safety equipment professionally installed, like a cage etc.

Three, you’ll probably end up needing a reliable daily driver, cause you will break sh1t, even at 500whp once in a while.

There’s more but I’m kinda tired and I’ve got other sh1t to say…

I feel you about easing into the power. I don't do dragstrips, but we don't need to go further into that convo... 40 or 50 rolls are better for axels anyway... at least until I hit big power I'm going to leave them for now. Roll cage and such are something I'll look into after I need the frame rigidity, and again, we're just in the planning stages... but I do understand that problem solving and chasing down issues is part of the game. Just so you know, I'm a 20+ year machinist with a fairly good grasp of the complexity and expenses we're discussing here, and I'm not taking any of this flippant. This money I'm going to spend is earned the old fashioned way, not inherited or anything, so I'm looking towards the solid group of people here to guide me. In the end I hope to have a machine that's solid, and an experience that was a challenge and a blast to do. A guy with no kids or wife needs something to keep him occupied... why not set a lofty goal to work hard for. Lastly, if I'm going to build, I'm going to try to do it as prudently as I can, and doing it in small steps only to go bigger later and throw more money at it at that time to upgrade what I just installed 2 seasons ago isn't a route I wish to follow.

FL 4Motion · 08-03-2021, 01:24 AM

Quote:

Originally Posted by oldskoolchuk

I'm not just going to jump out the window, with a car I don't know yet, with power I'm not used to. I appreciate the advice, good looking out. I appreciate it, I do. If I'm going to go up from here though, it's going to be a full build, rather than spend 7 grand on a stock long block to stay at the 500-600 range. Truthfully I'm going to have to upgrade my turbo system at the same time, and go to twin fuel pumps... and look at axels and a dif. I am going to have a look at your thread with my free time at work here, and glean what I can there... but again, if I'm going to spend money like this, it's not going to be a lateral move... it's going to be spend the money once and do what I want for long term goals. I have a lot to learn about what "do it right the 1st time" means... besides lots of overtime at work... or cashing in on equity. The planning is happening now though, and you guys are an incredible resource of knowledge and experience to learn from.

I’m going to go out on a limb that you’re a young guy, correct? Pls, pls if you hear nothing else, hear this, NEVER cash out equity, (home or investments, or retirement savings), to “invest” into a depreciating asset that will actually loose value the more $$ and mods you dump into it.

It’s no accident that the vast majority of us folks on here with heavily modded z’s or higher end fast cars and toys are middle aged or older. We took care of the student loans, the house, the cars etc and now have a bit of bit of disposable income to play.

I know that’s probably the last thing you want to hear but unless you’re a trust fund baby, (nothing wrong with that btw’), then you need to live in the real world.

Next topic, why a z?

If your goal is drag racing superstar, your way way better off looking at a different platform.

If it’s bc you love the z, and appreciate the heritage etc, I get that but just know this is the wrong tool for the task you’ve set out to conquer.

Unless your sponsored and getting paid, making a living to race then at the end of the day beating other people is just for your ego, and maybe a quick lay with a girl you definitely don’t wanna bring home to momma.

It’s easy to lose sigh5 of what really matters in life especially when you’re reading this forum and seeing all the IG hero builds etc, but you need to create a list of life goals and milestones you want to achieve both personally and professionally and I’m here to tell you, you’re 1/4 mile time and beating those stangs and camaros shouldn’t make the cut, that’s just entertainment and hobby. Making $$, becoming financially independent, owning your own house etc, that’s what makes a successful life and the playtime stuff will come naturally.

Alright, I know I sound like a old fuddyduddy killjoy but I’m not wrong.

oldskoolchuk · 08-03-2021, 01:37 AM

Quote:

Originally Posted by FL 4Motion

I’m going to go out on a limb that you’re a young guy, correct? Pls, pls if you hear nothing else, hear this, NEVER cash out equity, (home or investments, or retirement savings), to “invest” into a depreciating asset that will actually loose value the more $$ and mods you dump into it.

It’s no accident that the vast majority of us folks on here with heavily modded z’s or higher end fast cars and toys are middle aged or older. We took care of the student loans, the house, the cars etc and now have a bit of bit of disposable income to play.

I know that’s probably the last thing you want to hear but unless you’re a trust fund baby, (nothing wrong with that btw’), then you need to live in the real world.

Next topic, why a z?

If your goal is drag racing superstar, your way way better off looking at a different platform.

If it’s bc you love the z, and appreciate the heritage etc, I get that but just know this is the wrong tool for the task you’ve set out to conquer.

Unless your sponsored and getting paid, making a living to race then at the end of the day beating other people is just for your ego, and maybe a quick lay with a girl you definitely don’t wanna bring home to momma.

It’s easy to lose sigh5 of what really matters in life especially when you’re reading this forum and seeing all the IG hero builds etc, but you need to create a list of life goals and milestones you want to achieve both personally and professionally and I’m here to tell you, you’re 1/4 mile time and beating those stangs and camaros shouldn’t make the cut, that’s just entertainment and hobby. Making $$, becoming financially independent, owning your own house etc, that’s what makes a successful life and the playtime stuff will come naturally.

Alright, I know I sound like a old fuddyduddy killjoy but I’m not wrong.

I'm 43, have about 100k of equity, 23 years into the machining trade and making good money; no wife or kids to provide for, no debts, and a solid daily driver. Super appreciate what you're laying down here, but machines are my career and hobby. Yes, I know I'm going to piss money, and I'm ok with that... I don't go to drag strips though. Please also know that I'm not into the whole dying in a fiery wreck thing, so I'll be very respectful of the machine I'm trying to build... respecting powerful and dangerous machines has lead me to the success I have in this trade. Again, thank you for the wisdom.

FL 4Motion · 08-03-2021, 01:37 AM

Quote:

Originally Posted by oldskoolchuk

I feel you about easing into the power. I don't do dragstrips, but we don't need to go further into that convo... 40 or 50 rolls are better for axels anyway... at least until I hit big power I'm going to leave them for now. Roll cage and such are something I'll look into after I need the frame rigidity, and again, we're just in the planning stages... but I do understand that problem solving and chasing down issues is part of the game. Just so you know, I'm a 20+ year machinist with a fairly good grasp of the complexity and expenses we're discussing here, and I'm not taking any of this flippant. This money I'm going to spend is earned the old fashioned way, not inherited or anything, so I'm looking towards the solid group of people here to guide me. In the end I hope to have a machine that's solid, and an experience that was a challenge and a blast to do. A guy with no kids or wife needs something to keep him occupied... why not set a lofty goal to work hard for. Lastly, if I'm going to build, I'm going to try to do it as prudently as I can, and doing it in small steps only to go bigger later and throw more money at it at that time to upgrade what I just installed 2 seasons ago isn't a route I wish to follow.

That roll cage isn’t just for chassis rigidity, it’ll help there obviously, but it’s to keep you alive in the event of god forbid, the worst case scenario. If you’re roll racing in Mexico hypothetically, thats just as important as for the drag strip.

Congrats on 20+ years as a machinist, that’s awesome, we need more folks like that here.

Ok, I get wanting a fun hobby and not being tied down, just watch your spend cause builds like this tend to spiral outta control, all of use here have seen this movie many times over many years on this and other forums and in real life and some of us have even gone down this road. Bring a trailer is littered with 1/2 finished and 3/4 finished builds that the seller got too deep down the rabbit hole and then cut bait at a massive financial hit. Just wanted to try to help you not end up as that guy.

FL 4Motion · 08-03-2021, 01:45 AM

Quote:

Originally Posted by oldskoolchuk

I'm 43, have about 100k of equity, 23 years into the machining trade and making good money; no wife or kids to provide for, no debts, and a solid daily driver. Super appreciate what you're laying down here, but machines are my career and hobby. Yes, I know I'm going to piss money, and I'm ok with that... I don't go to drag strips though. Please also know that I'm not into the whole dying in a fiery wreck thing, so I'll be very respectful of the machine I'm trying to build... respecting powerful and dangerous machines has lead me to the success I have in this trade. Again, thank you for the wisdom.

Sounds like you’re doing well for yourself, that’s great. Best advise I can give then is spend a lot of time researching, making calls to shops, getting quotes for various parts, labor if you need help on something, and write it all down. Hen before you start, post that plan here so the guys who’ve already gone down this road can help fill in any blanks, get a ballpark $$ figure, and then let snowball start rolling down the hill. You’re gonna be building your car for about 2 years or so my best guess and that’s assuming a relatively smooth build.

oldskoolchuk · 08-03-2021, 02:46 AM

Quote:

Originally Posted by FL 4Motion

Sounds like you’re doing well for yourself, that’s great. Best advise I can give then is spend a lot of time researching, making calls to shops, getting quotes for various parts, labor if you need help on something, and write it all down. Hen before you start, post that plan here so the guys who’ve already gone down this road can help fill in any blanks, get a ballpark $$ figure, and then let snowball start rolling down the hill. You’re gonna be building your car for about 2 years or so my best guess and that’s assuming a relatively smooth build.

Yeah, this is a very significant undertaking, and I'm taking a good hard look at what it's all going to entail. My assumption is probably 30k and a lot of nights swearing in my garage. Even after it's all finished, drivetrain-wise there's the big investment in a widebody kit and suspension work I'll need to accomodate wider tires than the 305's I'm running now. But the motor is the biggest bite to chew... the rest will be smaller bites in comparison. As I see it if I run 800-900whp on a motor capable of 1000+ I should be in a good position to have her be dependable. Please correct me if I'm wrong on that.

Spooler · 08-03-2021, 08:47 AM

It's gonna cost more than that. Double it, that will put you in the ballpark if you get it right the first time. Starting with a high quality turbo kit will make your life easy. I would suggest you scrap whatever you have for a turbo kit and go with a Fast Intention kit. Do you want to fight to make 900whp or do you want to make it easy. What you do now will make it easy or harder for you to meet your goals.

redondoaveb · 08-03-2021, 10:16 AM

Quote:

Originally Posted by oldskoolchuk

Yeah, this is a very significant undertaking, and I'm taking a good hard look at what it's all going to entail. My assumption is probably 30k and a lot of nights swearing in my garage. Even after it's all finished, drivetrain-wise there's the big investment in a widebody kit and suspension work I'll need to accomodate wider tires than the 305's I'm running now. But the motor is the biggest bite to chew... the rest will be smaller bites in comparison. As I see it if I run 800-900whp on a motor capable of 1000+ I should be in a good position to have her be dependable. Please correct me if I'm wrong on that.

You don't need a wide body kit to run a wider rear tire, you just need the correct wheel offset and suspension set up. One member on here is running 345's. I'm running 315's and I believe Spooler is running 325's

cv129 · 08-03-2021, 10:51 AM

Quote:

Originally Posted by oldskoolchuk

My assumption is probably 30k

Quote:

Originally Posted by Spooler

Double it, that will put you in the ballpark if you get it right the first time.

RIP wallet

Rusty · 08-03-2021, 12:30 PM

Quote:

Originally Posted by redondoaveb

You don't need a wide body kit to run a wider rear tire, you just need the correct wheel offset and suspension set up. One member on here is running 345's. I'm running 315's and I believe Spooler is running 325's

Someone said 345's.

Spooler · 08-03-2021, 03:30 PM

You can stuff so much tire in the fenders of our cars it is crazy.

Z is 4 ZEBRA! · 08-03-2021, 04:01 PM

Check out Rearden

NISSAN 370Z GTS | for sale | Rearden

Looks like they offer building motors on top of fully built racecars.

SteveVQ · 08-03-2021, 05:04 PM

Quote:

Originally Posted by cv129

RIP wallet

I was quoted $45k for a "reliable" 850whp - 900whp. That's with Mazworx providing the majority of what's needed.

Obviously, that's if everything goes perfect and I know the odds of that happening are slim.

.

08-03-2021, 08:47 AM	#39 (permalink)
Spooler A True Z Fanatic Join Date: Jun 2014 Location: Ga Posts: 13,834 Drives: 2013 Nismo 370z Rep Power: 2684392	It's gonna cost more than that. Double it, that will put you in the ballpark if you get it right the first time. Starting with a high quality turbo kit will make your life easy. I would suggest you scrap whatever you have for a turbo kit and go with a Fast Intention kit. Do you want to fight to make 900whp or do you want to make it easy. What you do now will make it easy or harder for you to meet your goals. FL 4Motion, cv129, Rusty and 3 others like this.

08-03-2021, 03:30 PM	#43 (permalink)
Spooler A True Z Fanatic Join Date: Jun 2014 Location: Ga Posts: 13,834 Drives: 2013 Nismo 370z Rep Power: 2684392	You can stuff so much tire in the fenders of our cars it is crazy. FL 4Motion likes this.

08-03-2021, 04:01 PM	#44 (permalink)
Z is 4 ZEBRA! Base Member Join Date: Jun 2013 Location: SLC Posts: 71 Drives: 40th Nissan 370z Rep Power: 4252	Check out Rearden NISSAN 370Z GTS \| for sale \| Rearden Looks like they offer building motors on top of fully built racecars. Rusty and sx moneypit like this.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Engine builders 3.7 l in toronto area	Z eliminator	Canada	6	04-17-2021 07:39 PM
Insight Needed From Boosted Owners/Builders - Need Advice	AstatenateZ	Forced Induction	94	01-08-2020 12:09 PM
engine builders	HT Rambler	Texas	9	02-05-2016 05:48 PM
Engine builders	NIZZING	Engine & Drivetrain	2	09-09-2014 11:48 AM
Body Builders... What are you stacking??	Cell	Sports	26	08-11-2011 07:07 PM