Innovate dlg1

DrBacon · 05-11-2021, 12:35 AM

Anyone running an innovate dlg1? How the heck did you get the wires routed through the firewall. I tried going the same way I have my fuel pump power wire routed (behind the battery) but the connector is pretty thick, I would have to enlarge the hole a fair bit (there's two cables/connectors that must pass through, one for each bank o2 sensor).

madwi · 05-11-2021, 12:39 AM

The large grommet behind the battery area is where I pass all my wires and crap through. Stole these pics from oil pressure gauge thread.

Rusty · 05-11-2021, 10:11 AM

After you pass the wires through where Madwi showed. Put some RTV around the hole so that it doesn't leak.

DrBacon · 05-18-2021, 10:38 PM

So, not directly related to my initial question but if anyone comes across this thread in the future while looking up the dlg-1: If you install the o2 sensors slightly down stream (mine are just after the test pipes, in the Y pipe), the cable from the o2 sensors will not reach the gauge no matter how much of a direct path you try to take, it's off by 1-2 feet. You'll need an extension (not sure one exists). Innovate sells an 18foot cable that will work, you'll just have to hide the excess under the carpet or something I guess.

05-11-2021, 12:35 AM	#1 (permalink)
DrBacon Enthusiast Member Join Date: Nov 2016 Location: Washington Posts: 285 Drives: 2014 Nismo Rep Power: 27365	Innovate dlg1 Anyone running an innovate dlg1? How the heck did you get the wires routed through the firewall. I tried going the same way I have my fuel pump power wire routed (behind the battery) but the connector is pretty thick, I would have to enlarge the hole a fair bit (there's two cables/connectors that must pass through, one for each bank o2 sensor).

05-11-2021, 12:39 AM	#2 (permalink)
madwi A True Z Fanatic Join Date: Sep 2012 Location: West Michigan Posts: 31,410 Drives: Granma red Z Rep Power: 2684429	The large grommet behind the battery area is where I pass all my wires and crap through. Stole these pics from oil pressure gauge thread. Rusty and DrBacon like this.

05-11-2021, 10:11 AM	#3 (permalink)
Rusty Ronin Samurai - Assassin Join Date: Dec 2011 Location: Fayettenam,Pennsyltucky Age: 69 Posts: 35,381 Drives: 2011 Nismo GM 6M Rep Power: 2684438	After you pass the wires through where Madwi showed. Put some RTV around the hole so that it doesn't leak. DrBacon likes this. __________________ 浪人 - 殺し屋 "The Difficult Anytime, The Impossible By Appointment Only" http://www.the370z.com/members-370z-...o-journal.html

05-18-2021, 10:38 PM	#4 (permalink)
DrBacon Enthusiast Member Join Date: Nov 2016 Location: Washington Posts: 285 Drives: 2014 Nismo Rep Power: 27365	So, not directly related to my initial question but if anyone comes across this thread in the future while looking up the dlg-1: If you install the o2 sensors slightly down stream (mine are just after the test pipes, in the Y pipe), the cable from the o2 sensors will not reach the gauge no matter how much of a direct path you try to take, it's off by 1-2 feet. You'll need an extension (not sure one exists). Innovate sells an 18foot cable that will work, you'll just have to hide the excess under the carpet or something I guess. Last edited by DrBacon; 05-20-2021 at 06:55 PM.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[FOR SALE] Innovate A/F gauge	gsg740	Parts for sale (Private Classifieds)	0	06-26-2020 12:19 PM
innovate scg-1	arnoldas	Forced Induction	4	04-11-2019 03:59 PM
[FOR SALE] Innovate Boost Gauge and Innovate Dual Wideband Kit	Tusharp83	Parts for sale (Private Classifieds)	4	02-27-2019 08:18 PM
innovate wideband LC-1	Cell	Exterior & Interior	6	08-28-2013 08:49 AM
Innovate	djtodd	Exterior & Interior	3	12-10-2012 09:42 AM