Gear Lube in CV to Differential Flnage

Rusty · 02-23-2021, 09:17 PM

The stub axles I have sitting on the bench have centering dimples for machining. But no hole all the way through.

Check the back side of the CV joint for anything that doesn't look normal.

1slow370 · 02-24-2021, 06:39 PM

Quote:

Originally Posted by Rusty

The stub axles I have sitting on the bench have centering dimples for machining. But no hole all the way through.

Check the back side of the CV joint for anything that doesn't look normal.

This is what I thought. OP pop the stub axle out of the diff and see if it's damaged. If not I bet somebody just lubed the crap out of it when they put it together.

Tractionless · 03-03-2021, 10:51 AM

Quote:

Originally Posted by 1slow370

i have never seen a hole straight through the stub shaft.. usualy there is a little divot from the centerdrill used for machining but it shouldn't go all the way through? i would be tempted to say it is a defect but nissan might have changed it. it we be a really stupid place to put a vent holeas none of that area is sealed. i would be tempted to say someone lubed it for easy dissassembly. check to see if the hole goes all the through the stub flange if it does i would check with a dealer to see if they made a change to it and if not get a new stub flange.

What point would have they lubed for disassembly, bolt flange to CV or stub axle to housing?

Upon further inspection there isn't light shining through the stub so I assume the hole doesn't go all the way through.

Rusty · 03-03-2021, 09:23 PM

The only thing I can think of. This may have been a part before and they coated it with oil to keep from rusting.

1slow370 · 03-10-2021, 11:45 PM

Quote:

Originally Posted by Tractionless

What point would have they lubed for disassembly, bolt flange to CV or stub axle to housing?

Upon further inspection there isn't light shining through the stub so I assume the hole doesn't go all the way through.

there is only a fluid seal between the stub and the carrier housing if you had a leak you would expect fluid to be everywhere except where it is in your photos lol

02-23-2021, 09:17 PM	#16 (permalink)
Rusty Ronin Samurai - Assassin Join Date: Dec 2011 Location: Fayettenam,Pennsyltucky Age: 68 Posts: 35,271 Drives: 2011 Nismo GM 6M Rep Power: 2684438	The stub axles I have sitting on the bench have centering dimples for machining. But no hole all the way through. Check the back side of the CV joint for anything that doesn't look normal. __________________ 浪人 - 殺し屋 "The Difficult Anytime, The Impossible By Appointment Only" http://www.the370z.com/members-370z-...o-journal.html

03-03-2021, 09:23 PM	#19 (permalink)
Rusty Ronin Samurai - Assassin Join Date: Dec 2011 Location: Fayettenam,Pennsyltucky Age: 68 Posts: 35,271 Drives: 2011 Nismo GM 6M Rep Power: 2684438	The only thing I can think of. This may have been a part before and they coated it with oil to keep from rusting. __________________ 浪人 - 殺し屋 "The Difficult Anytime, The Impossible By Appointment Only" http://www.the370z.com/members-370z-...o-journal.html

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Differential gear install in Houston	JTM88	Texas	0	11-25-2017 03:13 PM
Due for differential gear oil change...	Jordo!	Nissan 370Z Warranty / Scheduled Maintenance / Servicing / Repairs	36	08-03-2014 01:17 AM
jiffy lube scam	boosted180	The Lounge (Off Topic)	14	08-22-2011 05:19 PM
Questions about oil cooler and differential gear oil	Rhett	Engine & Drivetrain	4	04-17-2010 01:45 PM