Oil change with oil cooler

TARDCORE · 01-19-2010, 10:19 AM

I haven't read anythingabout this but I am guessing it is common knowledge. Once I install the oil cooler, every oil change I have remove the front bumper cover, and remove the oil cooler, empty it out, then re install it, and re fill it after the oil from the pan drained correct? And when I first install it I have to install then fill the oil cooler itself before I put oil back into the block and pan itself correct? Sorry if this has been posted before. I am getting close to 1200 miles on my car and I want to do everything right without second guessing mysef.

LiquidZ · 01-19-2010, 10:25 AM

Quote:

Originally Posted by TARDCORE

I haven't read anythingabout this but I am guessing it is common knowledge. Once I install the oil cooler, every oil change I have remove the front bumper cover, and remove the oil cooler, empty it out, then re install it, and re fill it after the oil from the pan drained correct? And when I first install it I have to install then fill the oil cooler itself before I put oil back into the block and pan itself correct? Sorry if this has been posted before. I am getting close to 1200 miles on my car and I want to do everything right without second guessing mysef.

You can do that if you wish, but its not necessary. Cars with factory equipped coolers dont have to do this.

vipor · 01-19-2010, 10:50 AM

Some people opt to leave the ~1qt of "used" oil in the system and rely on the other 5 to offset the difference. I will probably be removing the oil cooler and draining it 1 out of every 3 oil changes myself.

Depending on how the cooler is installed, removal of the bumper will more than likely not be necessary, especially if the fittings are facing downwards.

Modshack · 01-19-2010, 11:18 AM

Quote:

Originally Posted by vipor

if the fittings are facing downwards.

You have no issues at all...Just pull off one of the AN fittings at the Adapter plate and let it drain.. If you installed with fittings "UP" like most of the kits out there, just undo BOTH AN fittings and use air pressure to blow the oil out. A little messy, but way easier then front end disassembly. If you're so anal that you need to get every drop out, then by all means turn this in to a major project. Personally, it's really not worth the effort (or necessary) IMO..

and NO, you don't have to manually fill the cooler before starting the engine....The VQ pump is very high volume and will fill it virtually instantly. Fresh Oil that is not up to temp will be largely sent to the engine rather than the cooler anyway (assuming the correct use of a thermostatic plate)

vipor · 01-19-2010, 11:25 AM

Quote:

Originally Posted by Modshack

You have no issues at all...Just pull off one of the AN fittings at the Adapter plate and let it drain.. If you installed with fittings "UP" like most of the kits out there, just undo BOTH AN fittings and use air pressure to blow the oil out. If you're so anal to need to get every drop out, then by all means turn this in to a major project. Personally, it's really not worth the effort IMO..

and NO, you don't have to manually fill the cooler before starting the engine..

haha didn't even think about removing the fittings at the sandwich plate. good thinkin' lincoln

now i just need to find a -10 AN compressor adapter. heh.

Modshack · 01-19-2010, 11:28 AM

Quote:

Originally Posted by vipor

i just need to find a -10 AN compressor adapter. heh.

Or just one of those cone shaped rubber blow gun tips you find in the $5 Harbor freight air kits...

vipor · 01-19-2010, 11:40 AM

tru dat homie g

tbonesteak · 01-19-2010, 10:15 PM

lolllll i thought of blowing the oil out of the cooler as well but thought you guys would think it's ridiculous and the idea would get shut down hard. But now that mod has said it, it is another option! You just need to cover the blow area with something clean and aim the other fitting down at the drain bucket and blow rite? HAHAHA this whole conversation is just funny.

TARDCORE · 01-19-2010, 10:19 PM

Hmmm sounds easy enough. So is there a difference to installing the kit with the hoses on the bottom instead of the top? I remember reading something in one of the many oil cooler threads.

edit: Ok so I install the cooler, put 5 qts in, run the car for a min or so, then add an additional quart or until it reads full is that how you guys do it?

vipor · 01-20-2010, 08:46 AM

Quote:

Originally Posted by tbonesteak

lolllll i thought of blowing the oil out of the cooler as well but thought you guys would think it's ridiculous and the idea would get shut down hard. But now that mod has said it, it is another option! You just need to cover the blow area with something clean and aim the other fitting down at the drain bucket and blow rite? HAHAHA this whole conversation is just funny.

just get someone's sister involved, she'll know what to do

vipor · 01-20-2010, 08:51 AM

Quote:

Originally Posted by TARDCORE

Ok so I install the cooler, put 5 qts in, run the car for a min or so, then add an additional quart or until it reads full is that how you guys do it?

sounds about right, but you may not even need to wait a full minute. i've heard the VQ pump is a beast.

TARDCORE · 01-20-2010, 12:30 PM

Quote:

Originally Posted by vipor

sounds about right, but you may not even need to wait a full minute. i've heard the VQ pump is a beast.

ok cool. Man I can't believe I started buying mods for the Z and I haven't even hit 1200 miles on it. Dam this crap is addicting. Apparently the fund for my modding my car told the fund towards buying a house to

01-19-2010, 10:19 AM	#1 (permalink)
TARDCORE Enthusiast Member Join Date: Jul 2009 Location: San Diego Posts: 410 Drives: 2010 Solid Red 370Z Rep Power: 16	Oil change with oil cooler I haven't read anythingabout this but I am guessing it is common knowledge. Once I install the oil cooler, every oil change I have remove the front bumper cover, and remove the oil cooler, empty it out, then re install it, and re fill it after the oil from the pan drained correct? And when I first install it I have to install then fill the oil cooler itself before I put oil back into the block and pan itself correct? Sorry if this has been posted before. I am getting close to 1200 miles on my car and I want to do everything right without second guessing mysef. __________________ XBL:EVENTYDE

01-19-2010, 10:50 AM	#3 (permalink)
vipor A True Z Fanatic Join Date: Aug 2009 Location: Euless, TX [ DFW ] Age: 42 Posts: 13,531 Drives: Nismo 09-0183 QAB Rep Power: 49	Some people opt to leave the ~1qt of "used" oil in the system and rely on the other 5 to offset the difference. I will probably be removing the oil cooler and draining it 1 out of every 3 oil changes myself. Depending on how the cooler is installed, removal of the bumper will more than likely not be necessary, especially if the fittings are facing downwards. __________________ 2009 NISMO # 0193 \| QAB \| Albums! \| 05.04.10 (Dynojet) 291.94hp/248.28tq Oil Cooler (DIY) \| Custom Headlights \| GTSPEC Braces \| F.I. Long Tube Headers

01-19-2010, 11:40 AM	#7 (permalink)
vipor A True Z Fanatic Join Date: Aug 2009 Location: Euless, TX [ DFW ] Age: 42 Posts: 13,531 Drives: Nismo 09-0183 QAB Rep Power: 49	tru dat homie g __________________ 2009 NISMO # 0193 \| QAB \| Albums! \| 05.04.10 (Dynojet) 291.94hp/248.28tq Oil Cooler (DIY) \| Custom Headlights \| GTSPEC Braces \| F.I. Long Tube Headers

01-19-2010, 10:19 PM	#9 (permalink)
TARDCORE Enthusiast Member Join Date: Jul 2009 Location: San Diego Posts: 410 Drives: 2010 Solid Red 370Z Rep Power: 16	Hmmm sounds easy enough. So is there a difference to installing the kit with the hoses on the bottom instead of the top? I remember reading something in one of the many oil cooler threads. edit: Ok so I install the cooler, put 5 qts in, run the car for a min or so, then add an additional quart or until it reads full is that how you guys do it? __________________ XBL:EVENTYDE Last edited by TARDCORE; 01-19-2010 at 10:24 PM.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
First Oil Change?	Rhinetom	Engine & Drivetrain	31	08-19-2014 10:07 PM
Nissan Motorsports Oil Cooler vs. Stillen Oil Cooler	Dustin@Z1	Engine & Drivetrain	158	03-10-2014 02:27 PM
Oil Cooler.....Trans Cooler...	kannibul	Engine & Drivetrain	6	12-31-2009 06:32 PM
1st oil change	KiddAdelaide	Australia/New Zealand	8	08-26-2009 04:58 PM
First Oil Change	cotizi	Engine & Drivetrain	3	03-27-2009 11:34 AM

01-19-2010, 10:15 PM	#8 (permalink)
tbonesteak Track Member Join Date: Mar 2009 Location: Socal Posts: 914 Drives: MY09 MB 6MT Rep Power: 376	lolllll i thought of blowing the oil out of the cooler as well but thought you guys would think it's ridiculous and the idea would get shut down hard. But now that mod has said it, it is another option! You just need to cover the blow area with something clean and aim the other fitting down at the drain bucket and blow rite? HAHAHA this whole conversation is just funny.