Oil Cooler Leaking?

SouthArk370Z · 04-27-2020, 10:39 AM

Quote:

Originally Posted by 1/4atatime

It is the Z1 kit and that's what I'm thinking going to take.it off this afternoon clean it up tighten everything down and then test again. I read you aren't supposed to put any thread sealant on the AN fitting part is that correct. I did put some on the NPT part even though it has a o ring does that hurt it? I guess I just need to tighten everything a little more and check. How tight is too tight?

Before you start tightening things up, clean the area real well and see if the oil reappears. If the oil doesn't show back up, you are good to go.

If you have an o-ring, you will be better off without the sealant. A little thread sealer will not hurt if you have an o-ring seal but most people use way too much.

Too tight is when you break something.

You might be able to find some torque specs online.

1/4atatime · 04-27-2020, 10:57 AM

Quote:

Originally Posted by SouthArk370Z

Before you start tightening things up, clean the area real well and see if the oil reappears. If the oil doesn't show back up, you are good to go.

If you have an o-ring, you will be better off without the sealant. A little thread sealer will not hurt if you have an o-ring seal but most people use way too much.

Too tight is when you break something.

You might be able to find some torque specs online.

Thanks for the info. I didn't apply a lot so I think I'm good in that area. My plan is to clean everything really well and double check to make sure nothing is loose leaving fittings alone that feel securely tightened. Hopefully everything is good.

dts3 · 04-27-2020, 10:58 AM

Quote:

Originally Posted by JARblue

Sounds like a mishitmoto sandwich plate. Good thing it didn't fail while driving and dump all your oil out on the road

It was actually a Mocal. The plate was perfect, just had s gasket that failed qc

dts3 · 04-27-2020, 11:05 AM

Did you put a little oil on the o-ring/gasket before you tightened it down?
I didn't use thread sealant on the AN fittings, but I used a compound (I hate the tape) in all the bspt and npt fittings. It worked so well that it sealed a bspt->npt junction with no leaks (they're similar at that size but not exact). If you go that route make sure to get one rated to the temperature and pressure that you'll expect to see

1/4atatime · 04-27-2020, 06:47 PM

Thanks for all the help everyone! I think everything is good to go!

I cleaned everything off and checked all the fittings and everything looks good now. I took it out for a test drive after everything was done and I didn't see any oil on it afterwards. Still going to keep checking it and doing some more hard runs next weekend to verify but knock on wood I think it's good. I also made a block off plate (75% blocked off) because it's still a little chilly and it really helped get the temps up.

BettyZ · 04-27-2020, 08:59 PM

Great to hear! Don't forget ab the oil pressure gauge. A good one (Defi, 150 psi) will run you 200-300. A new engine will be substantially more.

Sent from my SM-G955U using Tapatalk

dts3 · 04-27-2020, 09:19 PM

Quote:

Originally Posted by BettyZ

Great to hear! Don't forget ab the oil pressure gauge. A good one (Defi, 150 psi) will run you 200-300. A new engine will be substantially more.

Sent from my SM-G955U using Tapatalk

I have a Defi advance oil pressure and I can vouch for it... It's awesome. And it looks almost 100% stock

BettyZ · 04-27-2020, 09:48 PM

Quote:

Originally Posted by dts3

I have a Defi advance oil pressure and I can vouch for it... It's awesome. And it looks almost 100% stock

This! The gauge color is close enough to OEM that it's hard to tell the difference. I bought my gauge pod A pillar finisher from RDZ Motorsports. Very happy with it.

04-27-2020, 11:05 AM	#19 (permalink)
dts3 Track Member Join Date: May 2018 Location: Farmington Hills, MI Posts: 599 Drives: 08 Expedition Rep Power: 6765	Did you put a little oil on the o-ring/gasket before you tightened it down? I didn't use thread sealant on the AN fittings, but I used a compound (I hate the tape) in all the bspt and npt fittings. It worked so well that it sealed a bspt->npt junction with no leaks (they're similar at that size but not exact). If you go that route make sure to get one rated to the temperature and pressure that you'll expect to see __________________ Visit my blog! www.LeftoverPi.com Last edited by dts3; 04-27-2020 at 11:07 AM.

04-27-2020, 08:59 PM	#21 (permalink)
BettyZ A True Z Fanatic Join Date: Aug 2018 Location: Chicagoland Age: 38 Posts: 5,261 Drives: A Garage Queen Rep Power: 2684371	Great to hear! Don't forget ab the oil pressure gauge. A good one (Defi, 150 psi) will run you 200-300. A new engine will be substantially more. Sent from my SM-G955U using Tapatalk dts3 and 1/4atatime like this. __________________ '14 MB Nismo \| Boost Lab 6870 1.32 AR 553 HP / 471 ft.-lbs. Betty Mods

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Leaking oil cooler fittings on Z1 kit	obender66	Engine & Drivetrain	40	05-21-2017 01:39 PM
something is leaking! HELP!!!	ShockWave	Engine & Drivetrain	45	05-15-2016 10:46 PM
Coolant leaking	lhinojos	Nissan 370Z Warranty / Scheduled Maintenance / Servicing / Repairs	4	01-24-2016 02:03 AM
Zenclosure Box Leaking.	Minhtin	Audio & Video	6	09-08-2014 10:21 PM
Oil cooler hose to elbow junction leaking	Nikon FM	GT MotorSports	16	08-10-2010 11:43 PM