Is it necessary to ger an Oil Cooler?

mokhan996

Nevermind now I see what this "Block off Plate" is lol. Some nice sheet metal and Velcro! Someone else told me about this in this thread, took me this long to figure it out

BettyZ

Imagine a super-thin sheet of aluminum or steel the height and width of the oil cooler. Imagine it flush against the front of the oil cooler. Then imagine it being held onto the cooler with duct tape lol

__________________
'14 MB Nismo | Boost Lab 6870 1.32 AR 553 HP / 471 ft.-lbs.
Betty Mods

mokhan996

Yeahhh seen it haha. Thanks!

Rusty

Serious question. How old are you and what do you do for a living? Trying to figure out a couple of things. Like your mechanical back ground. Because some of the terms you are having a hard time with. If we know. Might be easier to explain some things.

__________________

浪人 - 殺し屋
"The Difficult Anytime, The Impossible By Appointment Only"
http://www.the370z.com/members-370z-...o-journal.html

mokhan996

23, Auto Tech. If I don't understand some words it's only because I've been taught or learned to say it differently or I may have never heard of it such as a "Block off Plate". I'm not an A tech if you wanna know haha, nowhere near it, but yeah, like they're terms where I have no clue of wtf it is, until I see it and say "Oh ok its such and such". Nah I'm sayin? For example someone came up to me talking about his engine cradle is rusted out. I'm like wtf is that? He points and says, "that". I'm like " You mean a fu'cking subframe??" Hes like yeahhh same thing.. Like calling it an engine cradle will mean that entire piece is physically holding the engine nothing else but I can drop the SUBFRAME/ENGINE CRADLE and the motor will still be intact. You say "Rocker Cover" I say "Valve Cover" so that's where I'm getting at. Just not used to other terms of what I usually know.

Jayhovah

__________________
2013 Gun Metallic Sport - Gamma V3 Twin Turbogized
DIY Gamma V3 TT Install * Jayhovah's Gamma V3 TT Install Pic'Z and Vid'Z * DIY: Washer Reservoir for the Boosted

BettyZ

Well you definitely know what questions to ask, which is a lot more than I can say when I start a project lol

Sent from my SM-G955U using Tapatalk

__________________
'14 MB Nismo | Boost Lab 6870 1.32 AR 553 HP / 471 ft.-lbs.
Betty Mods

mokhan996

you good?

SPDKING

Check this thread out I and everyone else put together.
Must have upgrades for every 370Z

On all 370Z's, daily driven to track car, all need a oil cooler and a CSC elimination kit or a heavy duty CSC. The oil cooler was my first upgrade not a week after getting my car after it went into limp mode driving normally to my job when it was 70 degrees out. I got the Z1 34 row with Setrab and the protective wrap with the thermostatic sandwich plate even though I live in Southern California just to be safe. I would stay away from Mishimoto's products and I heard good things about the Stillen and Fast Intentions oil coolers. At this point, it's a requirement on every single 370Z to have a oil cooler.

__________________
Stillen front and rear sway bars/Continental Extreme Tires/Annex Suspension Coilovers/Z1 Oil Cooler/Borla Catback Exhaust/K&N Drop in filters/SPL

Jayhovah

I've been feeling a little tired, but I think I just need to get more sleep

__________________
2013 Gun Metallic Sport - Gamma V3 Twin Turbogized
DIY Gamma V3 TT Install * Jayhovah's Gamma V3 TT Install Pic'Z and Vid'Z * DIY: Washer Reservoir for the Boosted

Rusty

You was born tired.

__________________

浪人 - 殺し屋
"The Difficult Anytime, The Impossible By Appointment Only"
http://www.the370z.com/members-370z-...o-journal.html

Rusty

Terminology can kill you real quick. Sometimes, it's like speaking a different language. For me. Going from steam turbine ( old school) to gas turbine (new school) . Two different words mean the same thing, the same piece of equipment. Best part, the damn pieces of equipment sit side by side. They tell you to work on piece X, but mean piece Y. You better check to make sure. If not. It could kill you.

__________________

浪人 - 殺し屋
"The Difficult Anytime, The Impossible By Appointment Only"
http://www.the370z.com/members-370z-...o-journal.html

Jayhovah

You ain't lying!

Sent from my Nexus 6P using Tapatalk

__________________
2013 Gun Metallic Sport - Gamma V3 Twin Turbogized
DIY Gamma V3 TT Install * Jayhovah's Gamma V3 TT Install Pic'Z and Vid'Z * DIY: Washer Reservoir for the Boosted

The Z Philes

Weird. I see all of this about an oil cooler being a requirement, yet the highest temp I've seen on mine has been just shy of 200, and that was on a 90 degree day here in Florida. And since it's still new and I'm still having fun, I haven't been light on the throttle. I guess I have some questions. Like what's considered a high oil temp on this car? And what is limp mode? Is there anything in particular I should be looking for? And I assume CSC is clutch slave cylinder. So these fail at a ridiculous rate, then?

JARblue

If you see 240 on the oil temp gauge, you can be sure the engine is already pulling timing. Expect actual oil temps to be about 20 degrees higher than the gauge. There are several levels of limp mode based on the temps. The last one is triggered around 280F actual oil temp and restricts RPMs to 3500.


CSC is a ticking time bomb. It will fail eventually. Best you can do without replacing it is hope you don't get stranded somewhere.

__________________