Coolerworx shifter

gshort24 · 12-05-2019, 10:03 PM

Any rev match issues with quick shifts?

redondoaveb · 12-05-2019, 10:14 PM

Quote:

Originally Posted by gshort24

Any rev match issues with quick shifts?

Nope

Hotrodz · 12-06-2019, 12:34 AM

Quote:

Originally Posted by redondoaveb

Nope

Agreed!

Sent from my SM-G965U using Tapatalk

Overlimit · 03-24-2020, 11:12 AM

How is the noise after installing this? I saw someone selling this on the classifieds because it was too loud for DDing. Perhaps a thin rubber gasket between the plate and mounting area would help?

NorthStyle · 03-24-2020, 04:06 PM

It's not too bad (especially with the NVH of the Z as-is). However, there can be a buzz at higher rpm's caused by the shifter rattling against itself. I reused the OEM rubber dust shield between the Coolerworx plate and the tunnel and it still does it. Some say the newer versions don't do it, but I don't think it's loud or annoying enough to get rid of the part.

Overlimit · 05-19-2020, 03:30 PM

Just got my Coolerworx shifter - any tips on install or guide available for reference? This was a message I received from BlackFlagBudget on reddit who installed the shifter on his 350z. Apparently there was this bracket that needs to be removed, is that the same on the 370z?

Quote:

You'll need to lower the transmission, but won't have to take it all the way out. Put the car on jack stands, put your jack underneath the trans, and remove the transmission mount. You'll be able to lower the trans just enough to get the bolts on the bracket out. They are small bolts and easy to break loose. The OEM shifter needs to be out first of course.

madwi · 05-19-2020, 03:36 PM

Quote:

Originally Posted by Overlimit

Just got my Coolerworx shifter - any tips on install or guide available for reference? This was a message I received from BlackFlagBudget on reddit who installed the shifter on his 350z. Apparently there was this bracket that needs to be removed, is that the same on the 370z?

The oem shifter assembly support has to be removed. Here it is:

I ended up using a stubby 12mm (I think) wrench to get at the top bolts that are on top of the trans housing.

NorthStyle · 05-19-2020, 04:24 PM

Quote:

Originally Posted by Overlimit

Just got my Coolerworx shifter - any tips on install or guide available for reference? This was a message I received from BlackFlagBudget on reddit who installed the shifter on his 350z. Apparently there was this bracket that needs to be removed, is that the same on the 370z?

I did a DIY on the original thread posted by Soho:

Coolerworx Shifter Assembly (Dealers)

Starts from Page 2

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
DIY: TWM Short Shifter and Leather Shifter Boot	GaleForce	DIY Section (Do-It-Yourself)	84	04-11-2018 05:42 PM
Aftermarket 370Z shifter handle and shifter knobs for automatic transmissions	Quicksilvers	Exterior & Interior	17	03-25-2018 10:48 AM
What is the best short-throw shifter and shifter knob combo?	ZInferno0248	Nissan 370Z General Discussions	79	03-06-2017 07:57 AM
[FOR SALE] OEM shifter	bkngo	Parts for sale (Private Classifieds)	3	06-19-2015 08:13 PM
shifter	z34/35	Engine & Drivetrain	2	07-24-2009 06:57 AM

12-05-2019, 10:03 PM	#91 (permalink)
gshort24 Base Member Join Date: Jul 2015 Location: California Posts: 22 Drives: 2009 370Z Rep Power: 10	Any rev match issues with quick shifts?

03-24-2020, 11:12 AM	#94 (permalink)
Overlimit Base Member Join Date: Jun 2010 Location: 951 Posts: 151 Drives: F80 M3 Rep Power: 33	How is the noise after installing this? I saw someone selling this on the classifieds because it was too loud for DDing. Perhaps a thin rubber gasket between the plate and mounting area would help?

03-24-2020, 04:06 PM	#95 (permalink)
NorthStyle A True Z Fanatic Join Date: Aug 2015 Location: Deutschland + SC/FL USA Posts: 1,259 Drives: 2011 370Z Nismo Rep Power: 24277	It's not too bad (especially with the NVH of the Z as-is). However, there can be a buzz at higher rpm's caused by the shifter rattling against itself. I reused the OEM rubber dust shield between the Coolerworx plate and the tunnel and it still does it. Some say the newer versions don't do it, but I don't think it's loud or annoying enough to get rid of the part.