Using a Car lift on the 370z ( lift points)

Wilson2608

Okay sweet thank you

__________________
Stillen G3, z1 Intake Manifold, Stillen Headers, Z1 HFC's, Stillen Catback. 330whp 267 ft- lbs tuned at Z1 motorsports.

axmea?

I understand your question. I've used these points instead of pinch welds when servicing my car and never have issues. I've seen it used at the garage I've been using as well. The jackpoint thread showing the PW JDM image of the Z on the lift resembles the same point.

__________________

Wilson2608

Okay cool. And yes but that image shows him using a pad on his lift arm to contact the pinch weld in th front. I thought it was the spot i was reffering to at first as well

__________________
Stillen G3, z1 Intake Manifold, Stillen Headers, Z1 HFC's, Stillen Catback. 330whp 267 ft- lbs tuned at Z1 motorsports.

synolimit

My car rocks on the oem jack points on my lift. If i pushed the rear end, removed the diff, pulled down on the front etc etc the car would fall flat on its face in a horrible crash.

__________________
13 370z-

Wilson2608

Dang that’s crazy. It’s always just a PITA for me to get the car on the lift using the oem jack points because the arms won’t retract far enough unless i line it up perfect. Even then I never really felt confident putting it there because the pinch welds arnt long enough and i can’t get the lift arm pad to contact the whole pinch weld. The 370z’s have such a short wheelbase

__________________
Stillen G3, z1 Intake Manifold, Stillen Headers, Z1 HFC's, Stillen Catback. 330whp 267 ft- lbs tuned at Z1 motorsports.

2011 Nismo#91

Well you did remove almost everything from the rear half of the car, even a good portion of the fuel tank. It's not too surprising the center of gravity is almost in front of the front pinch welds. What are your corner weights now?

__________________
GTR TT 493Whp/431lbft, Ecutek, Southbend 6puck,Quaife, RPM RollBar 4Point, R888R, JRZ RSPro F(10R/10C) R(10R/6C) 1000f500r inlbs+150inlbs Tender, SPL everywhere.Full Specs

Wilson2608

Thanks for the helpful replies everyone. Feel much more confident knowing others use this point as well.

__________________
Stillen G3, z1 Intake Manifold, Stillen Headers, Z1 HFC's, Stillen Catback. 330whp 267 ft- lbs tuned at Z1 motorsports.

synolimit

I dont know, haven't weighed in a while. The roll cage added a good 100-200lbs back there though.

__________________
13 370z-

synolimit

I took a 2x4 block though, cut out a line in the center and pushed that up against the pinch welds and thinned the block so its flush with the bottom of the car. Now when the jack pushes up its putting the weight on a 3.5x3.5" block under the body and the weld. No worries now.

Attached Images

IMG_4495.jpg (56.6 KB, 22 views)

__________________
13 370z-

synolimit

.

Attached Images

IMG_4496.jpg (50.4 KB, 25 views)

__________________
13 370z-

synolimit

With a complete flat bottom i know my aim points the 4 square screws holding the flat panel to the block.

Attached Images

IMG_4497.jpg (49.6 KB, 24 views)

__________________
13 370z-

Wilson2608

That’s pretty smart syno. Never thought about doing it that way

__________________
Stillen G3, z1 Intake Manifold, Stillen Headers, Z1 HFC's, Stillen Catback. 330whp 267 ft- lbs tuned at Z1 motorsports.

bcfromfl

Does anyone keep a set of rubber pads to bring with the car when it's going to be put on a hydraulic lift -- to protect the pinch welds from damage? Just bought my first Z, and am anticipating wear and tear from the metal arms and/or sloppy positioning by mechanics. I see on Amazon both the slotted "hockey puck" type (more for rolling jacks) and also rectangular pads. Which would be best? I imagine impatient mechanics probably wouldn't want to fiddle with these to get them just right before lifting the car...

phunk

I have always just used a square cut of 2x4. Works like a charm at keeping the pinch looking great.

I wonder if anyone produces pads that you can clamp onto the pinch before leaving your car somewhere? If it was already stuck on the car, it might help enforce technicians to use it.

__________________

Wilson2608

That would be awesome especially for when sending the car to the shop. I have rubber pads on top of my lift arms/ jack but they arnt that thick. My pinch weld still looks good beside one spot on the right rear.

__________________
Stillen G3, z1 Intake Manifold, Stillen Headers, Z1 HFC's, Stillen Catback. 330whp 267 ft- lbs tuned at Z1 motorsports.