Hard to get in gear

Joe@ZSpeed · 01-17-2018, 12:34 PM

Quote:

Originally Posted by OldFart

I have a similar issue getting into 5th, but that was after the dealer had just installed a new CSC. I haven't gotten underneath the car, but isn't there an adjustable "stop" for the shifter? If I am careful, goes in smoothly, but if I just push it into 5th, seems like I go past the engagement point. Prior to that I wasn't having any issues except for the 1st to 2nd shift when cold...

This is an easy fix, Remove boots on top, You will find a steel plate with 3 bolts, Loosen bolts, put in 5th gear
Push plate up to shifter and tighten bolts. Or just take it back to dealer and make them fix it since they messed it up

cjwsrt6 · 02-20-2018, 12:13 AM

Wanted to bring the thread back up. Haven’t driven it much since I’ve gotten a beater but it shifts smoother, much easier in gear except when running it past say 5grand. It becomes very hard to get in gear and may grind slightly. Also when the clutch is coming back up I notice the pressure isn’t as strong. I was thinking about dropping it off and getting it re bled, hoping it’s that easy. If anyone’s had this issue please post up

cjwsrt6 · 03-04-2018, 08:09 PM

Up. Just wanted to check on any thoughts before I turn it to my mechanic next week

TreeSemdyZee · 03-04-2018, 10:51 PM

I’d been having a similar problem for a long time and I finally bled the master cylinder and it works much better now. Not perfect, but I may need to do it again or replace it.

03-04-2018, 10:51 PM	#19 (permalink)
TreeSemdyZee Premium Member Join Date: Dec 2009 Location: Kentuck-IANA Age: 60 Posts: 4,885 Drives: '09 370 & ‘14 Juke Rep Power: 27408	I’d been having a similar problem for a long time and I finally bled the master cylinder and it works much better now. Not perfect, but I may need to do it again or replace it. cjwsrt6 likes this. __________________ Borla S-Type \| Motordyne \| Z1 (lots) \| South Bend \| K&N \| Nismo/Nismo S-Tune \| Eibach \| Aerojacket \| Fujimara \| Spl \| ZSpeed Performance \| Kenwood-Infinity-Sound Ordnance \| Whiteline \| Ecutek \| Hotchkis \| Clazzio \| VQ Vortex \|Morimoto XB \|Dynosty Tune 329.64hp 265.73 ft/lb

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Ticking noises on 3rd gear and 1st gear jerk	Ni9TFiVE	Engine & Drivetrain	5	12-07-2015 06:04 PM
1st to 2nd gear hard to shift..	jamesj1996	Engine & Drivetrain	18	12-24-2014 11:31 AM
Hard Left Hard Right Turning Air Bubble?	JrumMusic	Wheels & Tires	9	12-03-2014 11:25 AM
okay don't rip on me too hard but...	edub370	Intake/Exhaust	11	07-23-2011 12:32 PM
hard to shift into 1st gear?	Pharmacist	Nissan 370Z General Discussions	12	08-11-2009 01:23 AM

02-20-2018, 12:13 AM	#17 (permalink)
cjwsrt6 Enthusiast Member Join Date: Apr 2014 Location: Alabama Posts: 452 Drives: 2005 crossfire Srt6 Rep Power: 11	Wanted to bring the thread back up. Haven’t driven it much since I’ve gotten a beater but it shifts smoother, much easier in gear except when running it past say 5grand. It becomes very hard to get in gear and may grind slightly. Also when the clutch is coming back up I notice the pressure isn’t as strong. I was thinking about dropping it off and getting it re bled, hoping it’s that easy. If anyone’s had this issue please post up

03-04-2018, 08:09 PM	#18 (permalink)
cjwsrt6 Enthusiast Member Join Date: Apr 2014 Location: Alabama Posts: 452 Drives: 2005 crossfire Srt6 Rep Power: 11	Up. Just wanted to check on any thoughts before I turn it to my mechanic next week