Car Died While Driving, Now Will Not Start. No Codes.

osburnrs · 11-05-2017, 07:02 AM

Does it run if you disconnect the sensor again?

Sent from my iPad using Tapatalk

Cyber370 · 11-05-2017, 08:53 AM

Well, it does appear to be sensor related. You just need to figure out why it won’t run with it hooked up. Did you buy an OEM sensor or aftermarket? Aftermarket crank sensors are notoriously known for not working properly. If it is indeed a Nissan OEM sensor, you need to make sure you got the right one.

ShaunB828 · 11-05-2017, 07:02 PM

Yeah it runs again if I d/c the sensor. I bought the sensor from Nissan itself and compared to the one I took out they are identical (item #).

Cyber370 · 11-06-2017, 09:31 AM

Quote:

Originally Posted by ShaunB828

Yeah it runs again if I d/c the sensor. I bought the sensor from Nissan itself and compared to the one I took out they are identical (item #).

Hmmm......you got me stumped. Are you sure that the wiring/ connector is not damaged or burnt?
It’s obvious that the car does not like or understand the signal it’s receiving (or not receiving) from your new crank sensor.
Will the car run with your old one hooked up? Try it?

Sent from my iPhone using Tapatalk

ShaunB828 · 11-06-2017, 05:02 PM

Yeah, I swapped them a couple times just to make sure as of right now, I get the code for crank sensor sense it is out. But with the new and old one, got no code.

The wiring should be fine sense it throws a code when I have it hanging, but yeah I am stumped too at this point.

juld0zer · 11-07-2017, 07:14 AM

Might have to take it to an auto electrician and ask them to scope the crank sensor for you.

Next step would be to inspect the tone ring on the flywheel - borescope and turn the engine over by hand. Manual or auto?

ShaunB828 · 11-07-2017, 11:54 PM

Yeah, it's a manual. Thanks for the info, I'll try and see what I can take a look into in regards the ECM and/or flywheel.

Telephone · 11-19-2017, 06:21 AM

Shaun, any update on this?

11-05-2017, 08:53 AM	#17 (permalink)
Cyber370 Track Member Join Date: Jul 2016 Location: Montreal, QC Canada Posts: 679 Drives: 2016 370Z Nismo 6MT Rep Power: 19372	Well, it does appear to be sensor related. You just need to figure out why it won’t run with it hooked up. Did you buy an OEM sensor or aftermarket? Aftermarket crank sensors are notoriously known for not working properly. If it is indeed a Nissan OEM sensor, you need to make sure you got the right one. __________________ "That’s when you know you’ve found somebody special. When you can just shut the fck up for a minute and comfortably enjoy the silence.”-Mia (Pulp Fiction)*

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Codes and more Codes? now no start...	instroke	Forced Induction	15	10-15-2015 11:51 PM
Almost died.	Minsu	The Lounge (Off Topic)	53	09-19-2015 05:00 AM
car died	brucelidat	Nissan 370Z General Discussions	16	08-05-2014 04:38 PM
Car Wont Start, Throttle Body Codes	Mitco39	Engine & Drivetrain	8	04-28-2014 11:43 AM
Driving with Ferrari's. How to start your morning.	Mt Tam I am	Nissan 370Z General Discussions	22	10-31-2011 11:26 AM

11-05-2017, 07:02 AM	#16 (permalink)
osburnrs Base Member Join Date: Nov 2012 Location: Louisiana Posts: 148 Drives: 2015 370Z Nismo Rep Power: 13	Does it run if you disconnect the sensor again? Sent from my iPad using Tapatalk

11-05-2017, 07:02 PM	#18 (permalink)
ShaunB828 Base Member Join Date: Oct 2016 Location: Gilbert, AZ Posts: 9 Drives: 09 370Z Rep Power: 9	Yeah it runs again if I d/c the sensor. I bought the sensor from Nissan itself and compared to the one I took out they are identical (item #).

11-06-2017, 05:02 PM	#20 (permalink)
ShaunB828 Base Member Join Date: Oct 2016 Location: Gilbert, AZ Posts: 9 Drives: 09 370Z Rep Power: 9	Yeah, I swapped them a couple times just to make sure as of right now, I get the code for crank sensor sense it is out. But with the new and old one, got no code. The wiring should be fine sense it throws a code when I have it hanging, but yeah I am stumped too at this point.

11-07-2017, 07:14 AM	#21 (permalink)
juld0zer Enthusiast Member Join Date: Nov 2012 Location: Sydney Posts: 428 Drives: 11 Nissan 370Z MB M6 Rep Power: 139	Might have to take it to an auto electrician and ask them to scope the crank sensor for you. Next step would be to inspect the tone ring on the flywheel - borescope and turn the engine over by hand. Manual or auto?

11-07-2017, 11:54 PM	#22 (permalink)
ShaunB828 Base Member Join Date: Oct 2016 Location: Gilbert, AZ Posts: 9 Drives: 09 370Z Rep Power: 9	Yeah, it's a manual. Thanks for the info, I'll try and see what I can take a look into in regards the ECM and/or flywheel.

11-19-2017, 06:21 AM	#23 (permalink)
Telephone Enthusiast Member Join Date: Dec 2011 Location: San Diego, CA Posts: 297 Drives: 2012 Sport M6 Rep Power: 13	Shaun, any update on this?