Sometimes Push Start doesnt start.

Bad Boy

Where can I locate this sensor?

Rusty

On your clutch pedal, under the dash.

__________________

浪人 - 殺し屋
"The Difficult Anytime, The Impossible By Appointment Only"
http://www.the370z.com/members-370z-...o-journal.html

PongSanity

What rusty said


Sent from my iPhone using Tapatalk

Bad Boy

Ima check it out tomorrow.

Bad Boy

So after inspecting the upper section of my clutch pedal, I noticed that the pedal is making full contact with the nipple that gets pushed in... and the electric plug is correctly plugged in.
Maybe the switch is slowly going bad and eventually it wont register my start at all?

If I were to replace it, do I just pull the electric plug and nothing will brake? Or is there a clip or something I should watch out for?

SouthArk370Z

You can check operation of the switch with a cheap VOM (available at most auto parts stores).

Adjustment and R&R procedures should be in the FSM (link in my sig).

__________________
Steering Lock Links - Search The370Z Bookmarklet - FSM @ NICOclub
Mankind has progressed past the need for war but we haven't evolved that far. - NachoMahma

brancky3

The upper switch is irrelevant, you want to look at the lower switch when the pedal is pressed down.

__________________

Bad Boy

I'm pretty sure I'm talking about the correct switch, any lower is the actual chrome pedal.

AaronB

Double check that you are checking the correct switch. The upper switch should be white and lower should be brown if I'm not mistaken.

mults

I've been having the same issue for the past year or so...tried changing key fobs, replaced the car's battery (wen't dead over the winter), but still every once-in-a-while it would not start. Even the dealer could find nothing wrong. So, last week, I crawled under the dash and readjusted the lower clutch pedal switch (14mm jam nut) and screwed it in (Clockwise) about 3/4 of a turn to allow the switch button to be depressed more. Since then, I have had ZERO issues...starts every time now.

You can't just push in the lower switch button itself and expect the vehicle to start. There is an upper switch (for the cruise control) that has to be "open" for the car to start. Two things have to happen for the car to start:

1) The lower clutch switch must be closed (pushed in with the pedal)
2) The upper clutch switch must be open (pushed out with the pedal)

Without BOTH of these switches in the right position, the car will not start...

Take a look at the attached pdf document. BTW, the "C" gap for the lower switch should be 0.1-1.0mm (0.004-0.039")

Attached Files

CLUTCH_SWITCHES.pdf (203.7 KB, 62 views)

__________________
mults
40th Anniversary 'Z', 312.06HP/260.58TQ (Dynosty EcuTek Tune)
Build Date/Number: 1/27/2010 #706
Berk HFC + CBE, R2C CAI, Clear Bra, Cleveland Z Club

Bad Boy

Thanks for all the details and information, Ill look more into it later when I have some time.
Ill report back to see if it is a complete fix.

darkphantom

OP - same issue happened to me when I first got my car, thought my RJM clutch pedal was screwing something up. Remove the clutch switch and clean the contact points with alcohol using eartips or something. Reassemble and voila, problem solved!

__________________
'13 PW M6 | Takeda | ARK GRiP V2 | H&R

Bad Boy

Sorry it took a while for me to get back at anyone with similar issues, I procrastinate a lot.
So I was able to remove the old switch by turning "clockwise" to unscrew... I learned the hard way after bending the frame a little. I had to use some pliers to bend it back in position.
Anyways I bought a new switch at the dealer for $25 plus a 14mm wrench for $10.
So far no signs of the previous symptoms.

ReLL954

Just bought a pedal sensor switch , thought it was going bad gonna check this out later thanks guys

Bad Boy

If you had symptoms like mine, that sometimes the car doesn't start on first push, it most likely is your clutch switch.
I haven't had any problems since.