VVEL and Jun cams

1slow370 · 12-27-2015, 12:25 AM

Just dont take off too much once you get through the heat treat its junk nissan sells different sized lifters, the exhaust lifters are available and fit both intake and exhaust. Also remember to check them under full ladder assembly torque while bolted to the heads the clearances change a lot as you tourque it all down.

Morfiy · 12-27-2015, 12:49 AM

Quote:

Originally Posted by 1slow370

Just dont take off too much once you get through the heat treat its junk nissan sells different sized lifters, the exhaust lifters are available and fit both intake and exhaust. Also remember to check them under full ladder assembly torque while bolted to the heads the clearances change a lot as you tourque it all down.

Cams are there, bolting all back. Following all torque moments from user manual Will fire up an engine today-tomorrow.

Elmo370z · 12-27-2015, 01:24 AM

Quote:

Originally Posted by Morfiy

Cams are there, bolting all back. Following all torque moments from user manual Will fire up an engine today-tomorrow.

what other supporting mods do you have with the cam?

Elmo370z · 12-27-2015, 01:25 AM

I'm about a year in-half away from installing my top end build

Morfiy · 12-27-2015, 01:30 AM

Quote:

Originally Posted by Elmo370z

what other supporting mods do you have with the cam?

As of performance, only cams. Then oil cooler, racing thermostat, silicone lines, oil catch tank and something else

Elmo370z · 12-27-2015, 01:37 AM

Nice, im interested in seeing what gains you get from the install. What tuning software are you going to use? Are installing the jun 288?

Morfiy · 12-27-2015, 01:51 AM

Quote:

Originally Posted by Elmo370z

Nice, im interested in seeing what gains you get from the install. What tuning software are you going to use? Are installing the jun 288?

Originally I was going to use UpRev, but now seriously thinking of Ecutek.
My last figure was - 300 hp with no software and major mods. Hope to see 320 hp on cams and soft

Elmo370z · 12-27-2015, 10:54 AM

awesome, can't wait to see the numbers

Morfiy · 12-27-2015, 10:55 AM

Quote:

Originally Posted by Elmo370z

awesome, can't wait to see the numbers

Sure

Morfiy · 12-28-2015, 11:38 AM

Cams installed, all good, no CE light, temps okey. Will drive to dealers to adjust idle.

Elmo370z · 12-28-2015, 11:45 AM

Quote:

Originally Posted by Morfiy

Cams installed, all good, no CE light, temps okey. Will drive to dealers to adjust idle.

Are you really located in russia?

Morfiy · 12-28-2015, 11:46 AM

Quote:

Originally Posted by Elmo370z

Are you really located in russia?

Haha ) yep bro ) Crimea, sanctioned area

brucelidat · 12-28-2015, 11:58 AM

Are there any tuners out there, particularly Ecutek?

Morfiy · 12-28-2015, 12:00 PM

Quote:

Originally Posted by brucelidat

Are there any tuners out there, particularly Ecutek?

They're, going to use Uprev, because Ecutek isn't in stock

brucelidat · 12-28-2015, 12:04 PM

Let us know how it goes. Did you have a baseline dyno form before installing the cams?

12-27-2015, 12:25 AM	#61 (permalink)
1slow370 A True Z Fanatic Join Date: Aug 2009 Location: In the D Posts: 3,732 Drives: v8 74 260z ;) Rep Power: 7251	Just dont take off too much once you get through the heat treat its junk nissan sells different sized lifters, the exhaust lifters are available and fit both intake and exhaust. Also remember to check them under full ladder assembly torque while bolted to the heads the clearances change a lot as you tourque it all down. Morfiy likes this. __________________ ANSWER PRICE LIST Answers - - - - - - - - - - - - - - - - $0.75 Answers (requiring thought) - - - - $1.25 Answers (correct) - - - - - - - - - - $12.50

12-28-2015, 11:38 AM	#70 (permalink)
Morfiy Base Member Join Date: Dec 2012 Location: Russia Posts: 209 Drives: 370Z "Authentic" Rep Power: 12	Cams installed, all good, no CE light, temps okey. Will drive to dealers to adjust idle. Elmo370z likes this.

12-28-2015, 11:58 AM	#73 (permalink)
brucelidat A True Z Fanatic Join Date: Jun 2011 Location: temple city, ca Posts: 2,432 Drives: 2011 370z 7AT GM Sp Rep Power: 31	Are there any tuners out there, particularly Ecutek? __________________ Works Emotion CR Ultimate - FI CBE w/ 18" resonators - Ecutek - eibach sways - Quaife - FI LTH w/race cats - kw v3 - spl - Topgunz SC - 488whp 398trq

12-28-2015, 12:04 PM	#75 (permalink)
brucelidat A True Z Fanatic Join Date: Jun 2011 Location: temple city, ca Posts: 2,432 Drives: 2011 370z 7AT GM Sp Rep Power: 31	Let us know how it goes. Did you have a baseline dyno form before installing the cams? __________________ Works Emotion CR Ultimate - FI CBE w/ 18" resonators - Ecutek - eibach sways - Quaife - FI LTH w/race cats - kw v3 - spl - Topgunz SC - 488whp 398trq

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Where to buy jun cams	Elmo370z	Engine & Drivetrain	0	06-13-2015 02:26 AM
Aftermarket Cams	LAVA	Engine & Drivetrain	13	02-09-2015 12:35 PM
Stroker Kit plus Cams	Carbon_z	Engine & Drivetrain	5	11-24-2014 12:35 PM
cams for 370	jlask370	Engine & Drivetrain	5	05-08-2013 06:23 PM
Cams for 370z	animal23	Nismo 370Z	2	01-24-2013 05:49 AM

12-27-2015, 01:25 AM	#64 (permalink)
Elmo370z A True Z Fanatic Join Date: Apr 2013 Location: st. petersburg Posts: 5,709 Drives: 09 nissan 370z Sp M6 Rep Power: 295378	I'm about a year in-half away from installing my top end build

12-27-2015, 01:37 AM	#66 (permalink)
Elmo370z A True Z Fanatic Join Date: Apr 2013 Location: st. petersburg Posts: 5,709 Drives: 09 nissan 370z Sp M6 Rep Power: 295378	Nice, im interested in seeing what gains you get from the install. What tuning software are you going to use? Are installing the jun 288?

12-27-2015, 10:54 AM	#68 (permalink)
Elmo370z A True Z Fanatic Join Date: Apr 2013 Location: st. petersburg Posts: 5,709 Drives: 09 nissan 370z Sp M6 Rep Power: 295378	awesome, can't wait to see the numbers