CJM Oil Pan

phunk

I use permatex Ultra-Gray for oil pans. Get the stock upper pan surface totally clean. Sometimes like a scotch pad or other light abrasive can be really useful for that, along with some brake cleaner for the residue.

With the new sealant I put a small bead all the way around and then use my finger tip to spread it to the entire contact surface area a rather thin coat - it doesnt take much and all the extra will squeeze out when tightening... but you do want to make surface the entire contact area has at least some coverage to be safe.

Just before lifting the pan up, I would use a q-tip or small tool to extract most of the sealant that I can from the bolt holes... this will prevent too much of the sealant getting into the threads which can be troublesome and cause over-torqueing as it lubricates the threads.

Go light on the oil drain plug... its just aluminum threads so it will not withstand over-torqueing too much. I can try and come up with a torque spec for it with some more testing but most people just do it be feel anyway.

__________________

scth83

Paid, PM for shipping details.

Japanjay

PMed for remainder owed.

SurfDog

Arrived!!!
ImageUploadedByTapatalk1439686891.194389.jpg
ImageUploadedByTapatalk1439686930.379233.jpg
More parts too pretty to hide up in the car!!

__________________
09 6spd Berk CBE, JWT cams, ZSpeed CSC, Stillen (25 row oil, brake cooling, sways, gen3 CAI), Passport (9500ci), Quaife LSD, Z1 400 hp kit, ss lines, pads, rotors, clutch etc, Phunk's pan and fuel starve fix

GaleForce

Winning!

__________________

ENT-Z

Did you put the safety wire in or did phunk?

BGTV8

Mine arrived on Friday ......... very Gucci

phunk

I've installed it to the ones that shipped so far except for BGTV8 since he said he was going to do it

__________________

nismo13807

omg! i cant wait to get mine!! looks sick

Japanjay

So sick!!!

ENT-Z

Sweet! Hook me up as well please!

SurfDog

Phunk did it. (Thx btw)

__________________
09 6spd Berk CBE, JWT cams, ZSpeed CSC, Stillen (25 row oil, brake cooling, sways, gen3 CAI), Passport (9500ci), Quaife LSD, Z1 400 hp kit, ss lines, pads, rotors, clutch etc, Phunk's pan and fuel starve fix

SurfDog

I have a stillen oil cooler (with bypass temp plate and bigger filter and Phunk's pan under there.

Question. Do you think the servicing opening in the Zspeed under tray will be big enough for me to change my oil???

(If not I might have a Zspeed tray for sale here soon)

__________________
09 6spd Berk CBE, JWT cams, ZSpeed CSC, Stillen (25 row oil, brake cooling, sways, gen3 CAI), Passport (9500ci), Quaife LSD, Z1 400 hp kit, ss lines, pads, rotors, clutch etc, Phunk's pan and fuel starve fix

phunk

I cannot comment about the accessibility of the oil filter with your setup... but I can say that the CJM oil pan has the drain plug on the opposite corner of the pan (rear driver-side). I believe that the drain plug location would be problematic for that access panel on your undertray.

However, since the drain plug is completely vertical on the CJM pan, a strategically placed 1.25" diameter hole-saw cut directly underneath the drain plug would allow you to quickly access the plug without having to remove the undertray again. Placement would be critical though to make sure the oil drains through the hole rather than streaming down the top of the undertray. A 19mm socket is 1" outside diameter, so perhaps a 1.5" hole would be more appropriate. Probably depends on how close the pan comes to the undertray... the further apart they are, the more margin needs to be provided for the trajectory of the draining oil.

__________________

VQZ34nismo

Surfdog, I have a setrab oil cooler with the temp plate also, when I do the oil change I have to take off the zspeed undertray to get to the oil filter


Sent from my iPhone using Tapatalk