Billet Oil Pump Gears and Backing Plate - Group Buy Interest??

andy_meng1024 · 03-01-2016, 10:50 PM

What's the price on gears and back plate only? Thanks.

iPhone

Chuck33079 · 03-01-2016, 10:53 PM

Quote:

Originally Posted by Total D

Okay guys, here's the run down of how everything will work out.

Pricing is as if you're providing your oil pump. So, we will leave it up to you, to whether or not you want to run a new pump or just send yours in. I can provide new pumps, if you decide that is the route you want to go.

Pricing is as follows (includes pump modifications, gears, and back plate). A minimum of 10 will need to be sold to make this happen. A 50% deposit will be taken, so that we can move forward with the gears and back plate, remaining balance due when ready to ship.

Qty 10 = $850

Qty 20 = $775

Retail will be $900 after the initial group buy is done. Again this includes pump modifications, billet gears, and billet back plate.

GB List

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

I'll keep this list updated as time progresses.

Thanks,

Jeremiah

So this will be available after the group buy? It's unlikely I can jump in right now, but I'm definitely interested down the line.

Total D · 03-01-2016, 11:07 PM

Quote:

Originally Posted by andy_meng1024

What's the price on gears and back plate only? Thanks.

iPhone

If the 10 pieces are met, you're looking at $730 for the gears and backplate. Then, $850 after the group buy. So, you're only spending $120 more for us to put it all together and modify the pump, plus it gives me better quality control over the whole process.

Quote:

Originally Posted by Chuck33079

So this will be available after the group buy? It's unlikely I can jump in right now, but I'm definitely interested down the line.

The goal is to keep these in production, uit it's definitely a numbers thing. I'm more concerned with getting the first 10 done, so we can make this a reality. I understand what you mean though. Let me know when you're ready and we can go from there.

Rusty · 03-02-2016, 12:29 AM

Price for a complete pump set-up? Pump, gears, backing plate, etc?

derraj06 · 03-02-2016, 12:59 AM

Quote:

Originally Posted by Total D

Great man, sounds good. Seems you have the correct supporting mods to go along with the pump, so I think you'll be good to go.

Very nice on the build, I think you'll have one heck of a setup when "finished". Are you staying stock stroke or increasing it?

New pumps are going for around $250 if I'm not mistaken. While that may push it closer to the Nismo pump, you're getting a lot more for the money. Better material for the gears, billet back plate, and a modified pump to help with cavatation at higher rpms.

Let me know when you're ready to move forward and we can go from there. Thanks for your interest man, much appreciated.

Timing wise, I probably wouldn't actually "need" it until November. That said, whenever you have 9 others and want to start I'll be a part of it. I'm seeing OEM pumps for ~$235.00 new so yeah I agree, better pump for about what the nismo costs.

As for stroke, I'm comparing thoughts with several people using a VHR for different things. Currently, I'm leaning toward staying with the stock stroke but I'm not the one that knows best. I am giving the requirements and working with people I trust to find the solutions we need to make this happen.

Total D · 03-02-2016, 08:11 AM

Quote:

Originally Posted by Rusty

Price for a complete pump set-up? Pump, gears, backing plate, etc?

You're looking at $1100 shipped for a complete assembly.

Quote:

Originally Posted by derraj06

Timing wise, I probably wouldn't actually "need" it until November. That said, whenever you have 9 others and want to start I'll be a part of it. I'm seeing OEM pumps for ~$235.00 new so yeah I agree, better pump for about what the nismo costs.

As for stroke, I'm comparing thoughts with several people using a VHR for different things. Currently, I'm leaning toward staying with the stock stroke but I'm not the one that knows best. I am giving the requirements and working with people I trust to find the solutions we need to make this happen.

Okay, that sounds good. I'll let you know when we get to that point, but I'm sure you'll see it as well, since you post in here haha.

I see, well good luck on whichever decision you go with. I'm running a billet crank with stock stroke but with a quite larger piston. Gets me right at 3.8L, where as you guys are already at 3.7L. You might want to looking into using a longer rod and setting the wrist pin further up into the piston and keep the stock stroke as well. That's how most of the GT teams are set up.

ban25 · 03-02-2016, 07:54 PM

It's a good price. I would go for a complete pump as I'm preparing to do an engine build now.

Total D · 03-02-2016, 11:06 PM

Quote:

Originally Posted by ban25

It's a good price. I would go for a complete pump as I'm preparing to do an engine build now.

Great man, we'd enjoy the opportunity to be a part of your build.

Let me know when you're ready and we can get you added to the list.

tchilders58 · 10-07-2016, 05:39 PM

Is this still being made or did it get chopped?

Rusty · 10-07-2016, 07:44 PM

Quote:

Originally Posted by tchilders58

Is this still being made or did it get chopped?

Total D hasn't been on here since 3/22/16.

Total D · 10-08-2016, 10:02 AM

Quote:

Originally Posted by tchilders58

Is this still being made or did it get chopped?

Still working them bud. We have a couple products being finished to be released for the VQ35. So, we will be busy with the VQ37 shortly after.

Quote:

Originally Posted by Rusty

Total D hasn't been on here since 3/22/16.

You're are right, been a little while. Haven't really had worth weight to post to be honest. Just know I'm still working on making this happen.

derraj06 · 10-18-2016, 11:46 AM

Still interested in this as well as I'm beginning to ramp up on the short block build.

Total D · 10-24-2016, 05:28 PM

Quote:

Originally Posted by derraj06

Still interested in this as well as I'm beginning to ramp up on the short block build.

Sounds good man. I'll keep you posted.

Total D · 11-20-2016, 09:09 PM

Enjoy!!

More details will come later, just know I haven't forgot about you guys.

Jeremiah

Total D · 01-20-2017, 06:17 PM

A little teaser

03-01-2016, 10:50 PM	#196 (permalink)
andy_meng1024 Premium Member Join Date: Nov 2009 Location: Taipei Posts: 233 Drives: 2012 370z Rep Power: 3382	What's the price on gears and back plate only? Thanks. iPhone __________________ Current: 2015 C200 / 2018 Cayenne / 2012 370z / 2012 C250 Coupe Gone: 2013 Cayenne / 2004 Cayenne S / 2003 SL55 AMG / 2008 C300 / 2006 350z / 2006 C280 4Matic

03-02-2016, 12:29 AM	#199 (permalink)
Rusty Ronin Samurai - Assassin Join Date: Dec 2011 Location: Fayettenam,Pennsyltucky Age: 68 Posts: 35,187 Drives: 2011 Nismo GM 6M Rep Power: 2684437	Price for a complete pump set-up? Pump, gears, backing plate, etc? __________________ 浪人 - 殺し屋 "The Difficult Anytime, The Impossible By Appointment Only" http://www.the370z.com/members-370z-...o-journal.html

03-02-2016, 07:54 PM	#202 (permalink)
ban25 Enthusiast Member Join Date: Nov 2009 Location: SF, CA Posts: 339 Drives: 17 C7 Z06 M7 Rep Power: 66	It's a good price. I would go for a complete pump as I'm preparing to do an engine build now. Total D likes this. __________________ 2017 Corvette Z06 7MT \| 1LE \| Stage 3 \| DSCSport

10-18-2016, 11:46 AM	#207 (permalink)
derraj06 Enthusiast Member Join Date: Jun 2013 Location: Huntsville, AL Posts: 406 Drives: MB 370z Rep Power: 12	Still interested in this as well as I'm beginning to ramp up on the short block build. Total D likes this. __________________ 2010 Monterey Blue 370Z

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Any interest in a Volk TE37 SL Group Buy again?	SE	Wheels & Tires	22	05-06-2013 03:49 PM
Group Buy-BC Racing BR coilover Interest thread	g37xck	Brakes & Suspension	1	03-22-2013 05:40 PM
Brake Pad Backing Plate Importance	fuzzywuzzy	Brakes & Suspension	4	07-08-2012 09:00 PM
Press Release: Flex Tools now has a 4 3/8 backing plate for the Flex XC 3401	DetailersDomain	Detailing / Washing / Waxing / Cosmetic Maintenance and Repair	3	02-21-2011 08:38 AM
Front license plate carbon fiber backing group buy!	SpawnAeroJohn	Nissan 370Z General Discussions	14	07-06-2009 10:04 PM

10-07-2016, 05:39 PM	#204 (permalink)
tchilders58 Base Member Join Date: Jan 2016 Location: Durant, OK Posts: 6 Drives: 2016 Red Spot 7 AT Rep Power: 9	Is this still being made or did it get chopped?