Yellow "Key" light after engine swap

TopgunZ · 01-26-2015, 10:54 AM

After swapping my built motor in and hooking everything up I get this yellow light which is the "Intelligent Key" light. The car will come on with accessory lights but when clutch is pressed and start button is pressed it shuts down everything.

The fob allows me to lock and unlock the car so it is still communicating with it.

I did try to start it the first time with the manifold off, fuel injector harness unplugged, and the spark plugs out, so I could lube everything up internally without pressure before it actually was running. After it did the key light to me i hooked everything up thinking it is sensing that sensors are unplugged. But, got the same results.

Do I need to tow this to a dealer to reprogram the key to the car? Is there any other way or "trick" to getting this yellow key light off and allowing the car to start?

Wondering if anyone with an engine swap has encountered this.

TopgunZ · 01-26-2015, 01:10 PM

Also, Could I try an ECU reset? Or would this throw my current Uprev Map back to default?

TopgunZ · 01-26-2015, 09:44 PM

When the famous "wheel lock" issue happens can you still turn the wheel?

TopgunZ · 01-26-2015, 09:48 PM

Car doesnt start. Everything shuts off after second push. No cel light comes on with accesory on even though every other light is on.

Also my bluetooth obd wont connect and says it cant find ecu. But it works fine on my ridgeline.

Any ideas?

Nut_N_Much · 01-26-2015, 09:50 PM

Not sure, why fob is acting up. I've done swap but never unplugged everything to bump it. ECU had a heart attack. Like getting legs blown off. If reset doesn't work I dont have an answer.

No, your MAP will still be there.

No, when wheel lock happens you wont be able to turn wheel. Need to make a bypass for it. DIY has a thread for it

TopgunZ · 01-26-2015, 09:56 PM

I would and tried the reset but you need a cel light to do it and one wont show up on the dash. Also my bluetooth obd wont connect stating no ecu detected.

Nut_N_Much · 01-26-2015, 10:03 PM

Quote:

Originally Posted by TopgunZ

I would and tried the reset but you need a cel light to do it and one wont show up on the dash. Also my bluetooth obd wont connect stating no ecu detected.

Not reading ECU sounds like a ground. Man this sucks, I hate trouble shooting from a laptop. Wish i was there.

Nut_N_Much · 01-26-2015, 10:08 PM

Did you disconnect harness from motor, or pull connections from fuse box.

If you pulled from fuse box to get motor out, sounds like the clips might not be fully seated.

Sorry man, I'm on muscle relaxers and trying to focus. Excuse my typing

imjello · 01-26-2015, 11:23 PM

Hello

What is second push? I am assuming ignition, on my 370z clutch in one press turns it on. Second would turn it off. No clutch two pushes only takes it to accessory on.

Is the car trying to turn over, does it ever turn over or just starter noise?
Cars only need fuel spark and air to run, so elimating what it does have is a good start for troubleshooting the problem.

Being that its a new motor, I would be curious if timing was set to TDC, if it turns over then shuts off. I have not searched to see if the z if an interfereance motor, but if it is you can damage stuff if timing is wrong.

If it comes on with a SES light, the immobalizer could be the issue. Remove the batter term for a min and try again. If not I assume a dealer visit to remove error. In the world of Hondas, the k swap requires Imm. to be disabled before they will run, if stock ect is used.

Found this basic t/s link on this forum also:: Why a car won't start - troubleshooting tips

TopgunZ · 01-26-2015, 11:29 PM

Lol. Its all good man. I'm just glad your helping.

So my obd is definitely not working. Tried connecting osiris and it wont connect, stating no ecu detected.

Ill look closer at the ecu tomorrow and look at grounds.

SouthArk370Z · 01-26-2015, 11:35 PM

Since OBD/CAN is out, I suspect one or more ECM connectors.

FWIW: You can have ESCL failure with the steering wheel free. The locking pin retracts but does not make the internal switches.

Edit: It could be a bad CAN wire - you may have cut and/or grounded one of the signal wires. The FSM has wiring diagrams and connector pinouts.

SouthArk370Z · 01-26-2015, 11:39 PM

No need for two threads

http://www.the370z.com/forced-induct...gine-swap.html

Trips · 01-26-2015, 11:45 PM

Quote:

Originally Posted by SouthArk370Z

No need for two threads

http://www.the370z.com/forced-induct...gine-swap.html

I agree.

Threads have been merged.

TopgunZ · 01-27-2015, 12:02 AM

The car wont even attempt to start. I first push the button to turn on acc. Then I push it again and hear a faint click then all gauges turn off and car acts the same as if you were to have just shut it off.

I pulled the entire harness out of the fire wall.

Tomorrow ill look at all grounds and fuses.

Presto · 01-27-2015, 09:09 AM

i think you have to disable NATS on the ecu?

01-26-2015, 10:54 AM	#1 (permalink)
TopgunZ A True Z Fanatic Join Date: Jun 2012 Location: Minneapolis Posts: 2,651 Drives: 06 350Z , 09 370Z MT Rep Power: 6834	Yellow "Key" light after engine swap After swapping my built motor in and hooking everything up I get this yellow light which is the "Intelligent Key" light. The car will come on with accessory lights but when clutch is pressed and start button is pressed it shuts down everything. The fob allows me to lock and unlock the car so it is still communicating with it. I did try to start it the first time with the manifold off, fuel injector harness unplugged, and the spark plugs out, so I could lube everything up internally without pressure before it actually was running. After it did the key light to me i hooked everything up thinking it is sensing that sensors are unplugged. But, got the same results. Do I need to tow this to a dealer to reprogram the key to the car? Is there any other way or "trick" to getting this yellow key light off and allowing the car to start? Wondering if anyone with an engine swap has encountered this. __________________ ROTREX SUPERCHARGER TUNER KITS - $6799/ CUSTOM STILLEN AIR TO AIR KITS -$2100/ 700+ WHP!! WWW.TOPGUNSPEEDWORKS.COM

01-26-2015, 01:10 PM	#2 (permalink)
TopgunZ A True Z Fanatic Join Date: Jun 2012 Location: Minneapolis Posts: 2,651 Drives: 06 350Z , 09 370Z MT Rep Power: 6834	Also, Could I try an ECU reset? Or would this throw my current Uprev Map back to default? __________________ ROTREX SUPERCHARGER TUNER KITS - $6799/ CUSTOM STILLEN AIR TO AIR KITS -$2100/ 700+ WHP!! WWW.TOPGUNSPEEDWORKS.COM

01-26-2015, 09:44 PM	#3 (permalink)
TopgunZ A True Z Fanatic Join Date: Jun 2012 Location: Minneapolis Posts: 2,651 Drives: 06 350Z , 09 370Z MT Rep Power: 6834	When the famous "wheel lock" issue happens can you still turn the wheel? __________________ ROTREX SUPERCHARGER TUNER KITS - $6799/ CUSTOM STILLEN AIR TO AIR KITS -$2100/ 700+ WHP!! WWW.TOPGUNSPEEDWORKS.COM

01-26-2015, 09:48 PM	#4 (permalink)
TopgunZ A True Z Fanatic Join Date: Jun 2012 Location: Minneapolis Posts: 2,651 Drives: 06 350Z , 09 370Z MT Rep Power: 6834	Wont start after new motor dropped in Car doesnt start. Everything shuts off after second push. No cel light comes on with accesory on even though every other light is on. Also my bluetooth obd wont connect and says it cant find ecu. But it works fine on my ridgeline. Any ideas? __________________ ROTREX SUPERCHARGER TUNER KITS - $6799/ CUSTOM STILLEN AIR TO AIR KITS -$2100/ 700+ WHP!! WWW.TOPGUNSPEEDWORKS.COM

01-26-2015, 09:50 PM	#5 (permalink)
Nut_N_Much A True Z Fanatic Join Date: Dec 2011 Location: Pensacola Florida Posts: 1,696 Drives: Awesome Car Rep Power: 26	Not sure, why fob is acting up. I've done swap but never unplugged everything to bump it. ECU had a heart attack. Like getting legs blown off. If reset doesn't work I dont have an answer. No, your MAP will still be there. No, when wheel lock happens you wont be able to turn wheel. Need to make a bypass for it. DIY has a thread for it __________________ Did new cool science stuff to the car !!! http://www.the370z.com/mazoc/99606-z...y-14-17-a.html http://www.the370z.com/diy-section-d...-w-videos.html

01-26-2015, 09:56 PM	#6 (permalink)
TopgunZ A True Z Fanatic Join Date: Jun 2012 Location: Minneapolis Posts: 2,651 Drives: 06 350Z , 09 370Z MT Rep Power: 6834	I would and tried the reset but you need a cel light to do it and one wont show up on the dash. Also my bluetooth obd wont connect stating no ecu detected. __________________ ROTREX SUPERCHARGER TUNER KITS - $6799/ CUSTOM STILLEN AIR TO AIR KITS -$2100/ 700+ WHP!! WWW.TOPGUNSPEEDWORKS.COM

01-26-2015, 10:08 PM	#8 (permalink)
Nut_N_Much A True Z Fanatic Join Date: Dec 2011 Location: Pensacola Florida Posts: 1,696 Drives: Awesome Car Rep Power: 26	Did you disconnect harness from motor, or pull connections from fuse box. If you pulled from fuse box to get motor out, sounds like the clips might not be fully seated. Sorry man, I'm on muscle relaxers and trying to focus. Excuse my typing __________________ Did new cool science stuff to the car !!! http://www.the370z.com/mazoc/99606-z...y-14-17-a.html http://www.the370z.com/diy-section-d...-w-videos.html

01-26-2015, 11:23 PM	#9 (permalink)
imjello Enthusiast Member Join Date: Nov 2014 Location: texas Posts: 285 Drives: F80 M3, S5 B9 Rep Power: 13	Hello What is second push? I am assuming ignition, on my 370z clutch in one press turns it on. Second would turn it off. No clutch two pushes only takes it to accessory on. Is the car trying to turn over, does it ever turn over or just starter noise? Cars only need fuel spark and air to run, so elimating what it does have is a good start for troubleshooting the problem. Being that its a new motor, I would be curious if timing was set to TDC, if it turns over then shuts off. I have not searched to see if the z if an interfereance motor, but if it is you can damage stuff if timing is wrong. If it comes on with a SES light, the immobalizer could be the issue. Remove the batter term for a min and try again. If not I assume a dealer visit to remove error. In the world of Hondas, the k swap requires Imm. to be disabled before they will run, if stock ect is used. Found this basic t/s link on this forum also:: Why a car won't start - troubleshooting tips

01-26-2015, 11:29 PM	#10 (permalink)
TopgunZ A True Z Fanatic Join Date: Jun 2012 Location: Minneapolis Posts: 2,651 Drives: 06 350Z , 09 370Z MT Rep Power: 6834	Lol. Its all good man. I'm just glad your helping. So my obd is definitely not working. Tried connecting osiris and it wont connect, stating no ecu detected. Ill look closer at the ecu tomorrow and look at grounds. __________________ ROTREX SUPERCHARGER TUNER KITS - $6799/ CUSTOM STILLEN AIR TO AIR KITS -$2100/ 700+ WHP!! WWW.TOPGUNSPEEDWORKS.COM

01-26-2015, 11:35 PM	#11 (permalink)
SouthArk370Z Premium Member Join Date: Nov 2010 Location: South Arkansas Posts: 8,435 Drives: 2014 Challenger Rep Power: 324198	Since OBD/CAN is out, I suspect one or more ECM connectors. FWIW: You can have ESCL failure with the steering wheel free. The locking pin retracts but does not make the internal switches. Edit: It could be a bad CAN wire - you may have cut and/or grounded one of the signal wires. The FSM has wiring diagrams and connector pinouts. Nut_N_Much likes this. __________________ Steering Lock Links - Search The370Z Bookmarklet - FSM @ NICOclub Mankind has progressed past the need for war but we haven't evolved that far. - NachoMahma Last edited by SouthArk370Z; 01-26-2015 at 11:37 PM.

01-26-2015, 11:39 PM	#12 (permalink)
SouthArk370Z Premium Member Join Date: Nov 2010 Location: South Arkansas Posts: 8,435 Drives: 2014 Challenger Rep Power: 324198	No need for two threads http://www.the370z.com/forced-induct...gine-swap.html __________________ Steering Lock Links - Search The370Z Bookmarklet - FSM @ NICOclub Mankind has progressed past the need for war but we haven't evolved that far. - NachoMahma

01-27-2015, 12:02 AM	#14 (permalink)
TopgunZ A True Z Fanatic Join Date: Jun 2012 Location: Minneapolis Posts: 2,651 Drives: 06 350Z , 09 370Z MT Rep Power: 6834	The car wont even attempt to start. I first push the button to turn on acc. Then I push it again and hear a faint click then all gauges turn off and car acts the same as if you were to have just shut it off. I pulled the entire harness out of the fire wall. Tomorrow ill look at all grounds and fuses. __________________ ROTREX SUPERCHARGER TUNER KITS - $6799/ CUSTOM STILLEN AIR TO AIR KITS -$2100/ 700+ WHP!! WWW.TOPGUNSPEEDWORKS.COM

01-27-2015, 09:09 AM	#15 (permalink)
Presto Base Member Join Date: May 2010 Location: Home Posts: 123 Drives: Car Rep Power: 15	i think you have to disable NATS on the ecu? Nut_N_Much likes this.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
"Service engine soon" light	import111	Engine & Drivetrain	71	06-29-2016 12:57 AM
"Limp Mode" & service engine light	BangZ	Engine & Drivetrain	6	01-14-2015 09:43 PM
2013 370z "SERVICE ENGINE SOON" light on	OEYBONJOVI	Nissan 370Z Warranty / Scheduled Maintenance / Servicing / Repairs	12	08-19-2013 06:47 PM
Help! Blown fuses and "Service Engine Soon" light	Kdberan	Exterior & Interior	2	11-29-2012 12:33 PM
Just got "Service Engine Soon" light..	dcrew1x	Nissan 370Z Warranty / Scheduled Maintenance / Servicing / Repairs	9	02-15-2012 07:38 PM