Z1 Motorsports: Clutch Concentric Slave Cylinder Elimination Kit

John@Z1 · 05-14-2014, 10:37 AM

Quote:

Originally Posted by JARblue

I will be calling you shortly to place my order

*edit* Ordered! Thanks for the help, John

Thank you sir! Please post up a review when installed.

omgZ · 05-16-2014, 01:04 AM

Quote:

Originally Posted by John@Z1

I missed those

Originally Posted by cavemancan View Post
Thanks for the input! Pedal feel alone justifies the cost for me.

This will mark the 3rd time the slave/master cylinder will need to be replaced on my car. 2 of which were under warranty. This last time I am out of factory warranty and I am left with my extended warranty but they are telling me it is not covered. Either way I think I am going to forgo the drama and just buy this. Have to save some pennies for the whole setup though. I plan to change the clutch, flywheel, CSC, and Master cylinder.

Last 3 question(s):
- Do you recommend rebuilding the master cylinder or replacing? I saw a rebuild kit for $18 which is better then paying $110 for a new one.
- Do you guys sell stock clutches? I plan to race the car NA but keep it a daily driver.
- Any suggestion for an upgraded clutch? I may consider an upgrade just trying to keep cost down.

Rebuilding or replacing the master cylinder is never a bad idea on the Z34 as they are known to have problems. I will say that we have never had to replace the master on the Z1 shop car and it has 36K ABUSED and track tested miles.

I would suggest the Z1 clutch and flywheel combo over going with a stocker as the Z1 flywheel will allow for quicker revs.

If I install the combo now, later on down the road could another clutch/flywheel combination be simply swapped in with no issue to the eliminator kit?

John@Z1 · 05-19-2014, 03:33 PM

Quote:

Originally Posted by omgZ

If I install the combo now, later on down the road could another clutch/flywheel combination be simply swapped in with no issue to the eliminator kit?

It all depends on which combo you install. If anything should need to be changed it should be fairly simple to change it.

JARblue · 05-19-2014, 04:46 PM

John,

I am preparing to do this work this week and had a question about the MT fluid. I recently did a flush, so I'm hesitant to change it again but willing. I'm just a little concerned about being able to properly tip the transmission (it will be chained to a transmission floor jack) to save the fluid. Any thoughts on how easy or difficult this might be? If it makes things easier, I've got a local cycle shop that can get it next business day.

John@Z1 · 05-19-2014, 05:01 PM

Quote:

Originally Posted by JARblue

John,

I am preparing to do this work this week and had a question about the MT fluid. I recently did a flush, so I'm hesitant to change it again but willing. I'm just a little concerned about being able to properly tip the transmission (it will be chained to a transmission floor jack) to save the fluid. Any thoughts on how easy or difficult this might be? If it makes things easier, I've got a local cycle shop that can get it next business day.

It's normally a 5.5hr job.

JARblue · 05-19-2014, 05:54 PM

Quote:

Originally Posted by JARblue

I'm just a little concerned about being able to properly tip the transmission (it will be chained to a transmission floor jack) to save the fluid. Any thoughts on how easy or difficult this might be?

Quote:

Originally Posted by John@Z1

It's normally a 5.5hr job.

I was specifically asking about the procedure of tipping the transmission to the rear in order to salvage the transmission fluid. Do you foresee any difficulty doing this using a transmission floor jack?

John@Z1 · 05-19-2014, 06:18 PM

Quote:

Originally Posted by JARblue

I was specifically asking about the procedure of tipping the transmission to the rear in order to salvage the transmission fluid. Do you foresee any difficulty doing this using a transmission floor jack?

O sorry, we have a trans plug for that. So be very careful when tilting. If you go to far fluid will leak from the rear.

JARblue · 05-19-2014, 06:22 PM

Quote:

Originally Posted by John@Z1

O sorry, we have a trans plug for that. So be very careful when tilting. If you go to far fluid will leak from the rear.

Gotcha. Yeah, I just decided to go ahead and do another flush. The last time I only had three quarts to fill anyway so I want to make sure it's full. Plus I know I would lose at least a little during the removal process. Since I needed one, might as well buy three more - easy to justify an extra $50 in the process of saving $800 in labor

*edit* I just wanted to add that I just purchased my transmission jack, and the jack itself has adjustments to tilt the transmission in any direction while it is chained to the jack. I will probably still go ahead and replace the fluids, but I now know that it wouldn't have been a problem to save most of the oil (provided I plug the rear). The dealer sold me the wrong washers for the plugs before my last flush, so I can put new washers on as well.

batboyvaj · 05-25-2014, 11:01 PM

You guys should do a group buy on this!

John@Z1 · 05-29-2014, 12:36 PM

Quote:

Originally Posted by batboyvaj

You guys should do a group buy on this!

Can't do that at the moment due to the high cost on our end

diego@vossen · 05-29-2014, 12:46 PM

Awesome!!! I think I will jump on this also for my 2013 G37 6MT.

Mike · 05-29-2014, 08:56 PM

Quote:

Originally Posted by diego@vossen

Awesome!!! I think I will jump on this also for my 2013 G37 6MT.

you won't be disappointed!

On another note, had a layover in Ft Lauderdale last month and saw a Vossen billboard, very cool!

John@Z1 · 06-02-2014, 01:55 PM

Quote:

Originally Posted by diego@vossen

Awesome!!! I think I will jump on this also for my 2013 G37 6MT.

Just let me know when you're ready Diego! Thanks for the input Mike!

anthony909 · 06-02-2014, 05:25 PM

Hey John I'm looking into using your new csc kit but the car also just had a tt kit thrown on it so I will need to upgrade my clutch and flywheel as well. Any recommendations for any clutch and flywheel kits that will work well with your csc? I know you guys have your own clutch set up but I'm wondering how it will hold up with the added power because I see some turbo guys using specialty-z clutch set ups but not so many with the z1 clutch set up? If anyone could chime in it would really help.

Thanks a lot!

MM'08_350Z · 06-03-2014, 10:21 PM

Hey John, I have a Spec Twin Disc Clutch that I will be installing on my HR Z. What can you do for me to get this CSC elimination kit on my Z before I send the Z in the to get the clutch installed.

Thanks,

Manny

05-19-2014, 04:46 PM	#49 (permalink)
JARblue A True Z Fanatic Join Date: Mar 2011 Location: Austin, TX Age: 44 Posts: 36,450 Drives: 11 Z34, 98 E36 M3 Rep Power: 2684440	John, I am preparing to do this work this week and had a question about the MT fluid. I recently did a flush, so I'm hesitant to change it again but willing. I'm just a little concerned about being able to properly tip the transmission (it will be chained to a transmission floor jack) to save the fluid. Any thoughts on how easy or difficult this might be? If it makes things easier, I've got a local cycle shop that can get it next business day. __________________ 2011 370Z 6MT Sport Gun Metallic \| ARC \| CJM \| Ecutek \| FI \| Fujimura \| R2C \| SPL \| Stillen \| TWM \| Z1 \| ZSpeed \|

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Clutch Slave cylinder broke @ 22K	chknhawk	Engine & Drivetrain	37	07-10-2018 11:46 AM
Clutch Slave Cylinder	Wiggins3377	Engine & Drivetrain	18	08-06-2015 10:26 AM
Clutch, Flywheel, and Slave Cylinder Combo Sale at R/T Tuning.	Erik@RTTuning	R/T Tuning	6	12-26-2012 01:10 PM
Clutch slave cylinder	NizzyBoy	Engine & Drivetrain	1	02-19-2011 03:24 PM

05-25-2014, 11:01 PM	#54 (permalink)
batboyvaj Base Member Join Date: Jun 2011 Location: mn Posts: 111 Drives: 2011 370z Rep Power: 14	You guys should do a group buy on this!

05-29-2014, 12:46 PM	#56 (permalink)
diego@vossen Track Member Join Date: Dec 2012 Location: Miami Posts: 614 Drives: Nismo 370Z 6MT Tech Rep Power: 14	Awesome!!! I think I will jump on this also for my 2013 G37 6MT.

06-02-2014, 05:25 PM	#59 (permalink)
anthony909 Base Member Join Date: Aug 2010 Location: CA Posts: 138 Drives: 2010 370zzzzz Rep Power: 15	Hey John I'm looking into using your new csc kit but the car also just had a tt kit thrown on it so I will need to upgrade my clutch and flywheel as well. Any recommendations for any clutch and flywheel kits that will work well with your csc? I know you guys have your own clutch set up but I'm wondering how it will hold up with the added power because I see some turbo guys using specialty-z clutch set ups but not so many with the z1 clutch set up? If anyone could chime in it would really help. Thanks a lot!

06-03-2014, 10:21 PM	#60 (permalink)
MM'08_350Z Base Member Join Date: Jun 2013 Location: Laredo Posts: 36 Drives: 08 350Z CS M6 Rep Power: 12	Hey John, I have a Spec Twin Disc Clutch that I will be installing on my HR Z. What can you do for me to get this CSC elimination kit on my Z before I send the Z in the to get the clutch installed. Thanks, Manny