RJM Clutch Pedal System for 370Z - Fully Customizable Clutch Feel & Stroke

scope22 · 02-29-2016, 04:29 PM

Quote:

Originally Posted by enrique_370

Ordered mine I am excited this is the cars last chance to feel perfect before I opt to get a stingray lol.

I'd wait for a GT350 if i were you

xdragus · 02-29-2016, 09:56 PM

Looking to purchase this but what proof do you have to back up your claims "Reduces or Eliminates the Concentric Slave Cylinder failures that are so common on these cars." on your website.

Would this potentially conflict with the zspeed hd csc or z1 csc elimination kit? can they be combined?

Chuck33079 · 02-29-2016, 10:09 PM

Quote:

Originally Posted by xdragus

Would this potentially conflict with the zspeed hd csc or z1 csc elimination kit? can they be combined?

They will work fine together.

Ryan @ RJM · 02-29-2016, 10:48 PM

Quote:

Originally Posted by xdragus

Looking to purchase this but what proof do you have to back up your claims "Reduces or Eliminates the Concentric Slave Cylinder failures that are so common on these cars." on your website.

Would this potentially conflict with the zspeed hd csc or z1 csc elimination kit? can they be combined?

xdragus,
Absolutely they work together no problem. I would personally recommend the HD CSC though as it's a very high quality piece and combined with the RJM pedal it'd be a bullet proof setup. For me the Z1 kit is overly complicated, requires a lot of extra work to install and addresses the same problem the HD CSC does but at a much higher installed cost.

For the proof of the "Reduces or Eliminates the CSC failures" this has been discussed about 4 times in this thread already above but the basics of it is this. The primary cause of OEM CSC failures is over stroking the internal piston and blowing out the weak seals. This happens because the OEM pedal/CMC pushes too much fluid to the CSC which coincidentally also causes the very high pedal engagement and huge dead space at the bottom of the pedal. The RJM pedal thru manipulation of the pedal geometry reduces the excess stroking which isn't needed for complete disengagement. This saves the seals from all the extra wear pointlessly stroking back/forth and because the CSC is no longer being forced to the very end of it's travel every time you fully depress the clutch it reduces or eliminates the seal blow-outs that lead to catastrophic CSC failure. As well with the RJM pedal you'd see longer service life from the HD CSC or the Z1 Kit for the same reason that you're not stroking the seals excessively on every shift and increasing seal life.

Hope that helps explain things.

Best Regards,
Ryan@RJM

xdragus · 03-02-2016, 10:08 PM

Just ordered.

Thanks

Ryan @ RJM · 03-03-2016, 11:49 AM

Quote:

Originally Posted by xdragus

Just ordered.

Thanks

xdragus, Thank you for your order

I just sent you a confirmation email with the install guide and shipping details.

Best Regards,
Ryan@RJM

N8GTOL · 03-06-2016, 11:11 PM

Ryan, I finally placed my order! Can't wait to feel the difference with this mod. Even if I have to relearn how to shift the car after making due with the current setup for 5+ years it should be worth the wait.

Swindler · 03-08-2016, 06:36 AM

Just placed an order for this after reading through all 27 pages and everything on the RJM website. Can't wait, super excited for sure! I removed the clutch helper spring over a year ago and it was a huge improvement. However it is still tricky with that high engagement point. I hope this new pedal will be as good as it sounds, very excited.

scope22 · 03-08-2016, 07:01 AM

Quote:

Originally Posted by Swindler

Just placed an order for this after reading through all 27 pages and everything on the RJM website. Can't wait, super excited for sure! I removed the clutch helper spring over a year ago and it was a huge improvement. However it is still tricky with that high engagement point. I hope this new pedal will be as good as it sounds, very excited.

it will be!

brancky3 · 03-08-2016, 07:34 AM

I ordered one a couple weeks ago, super excited for it to get here!

Ryan, are there any updates on when the units will be available? I believe the site said 3/7, just wanted to see if we're still on track

I was #9 of 25 IIRC.

Ryan @ RJM · 03-08-2016, 09:54 PM

Quote:

Originally Posted by N8GTOL

Ryan, I finally placed my order! Can't wait to feel the difference with this mod. Even if I have to relearn how to shift the car after making due with the current setup for 5+ years it should be worth the wait.

Quote:

Originally Posted by Swindler

Just placed an order for this after reading through all 27 pages and everything on the RJM website. Can't wait, super excited for sure! I removed the clutch helper spring over a year ago and it was a huge improvement. However it is still tricky with that high engagement point. I hope this new pedal will be as good as it sounds, very excited.

N8GTOL and Swindler thank you both for your orders

Ryan @ RJM · 03-08-2016, 10:04 PM

Quote:

Originally Posted by brancky3

I ordered one a couple weeks ago, super excited for it to get here!

Ryan, are there any updates on when the units will be available? I believe the site said 3/7, just wanted to see if we're still on track

I was #9 of 25 IIRC.

Hi Brancky3, Well I'm close

The laser cutters were a day late finishing the raw CNC cut parts for me but I made the 4hr run down there and back this afternoon so we wouldn't loose another day waiting on a shipping courier to deliver them tomorrow. That let me begin fabrication this evening and I'm currently planning an all nighter to get 1 thru 10 done for shipment by tomorrow afternoon. From there 11-20 should be ready for shipment Friday and the remaining few on Monday.

Currently I have just QTY 2 units remaining available from this latest batch. If anyone wants to get in for one before they sell out again better place your orders thru the RJM webstore quick! Otherwise ETA is 2-3 weeks wait for the next run.

Best Regards,
Ryan@RJM

Z50 · 03-15-2016, 12:53 AM

Somebody needs to tell the owner of this fine Z about this clutch pedal upgrade:

https://www.youtube.com/watch?v=zxXAlsSyloo

A wonderful choice of colour, might I add.

R6MT · 03-15-2016, 02:39 AM

Just got my shipping confirmation today showing that I get mine Friday! Can't wait to install it this weekend. Much appreciated!

brancky3 · 03-15-2016, 07:07 AM

Received mine yesterday, will be installing tomorrow.

03-08-2016, 07:34 AM	#400 (permalink)
brancky3 Track Member Join Date: Jun 2014 Location: Greer, SC Age: 37 Posts: 754 Drives: 14 370Z Gun Metallic Rep Power: 16	I ordered one a couple weeks ago, super excited for it to get here! Ryan, are there any updates on when the units will be available? I believe the site said 3/7, just wanted to see if we're still on track I was #9 of 25 IIRC. __________________ 2014 Nissan 370z Gun Metallic 6-spd Test Pipes \| Nismo CBE \| Stillen Gen3 \| Swift springs \| Advanation Sway Bars \| RJM Clutch \| GTR DBA Premium Wheels

03-15-2016, 12:53 AM	#403 (permalink)
Z50 Base Member Join Date: Oct 2015 Location: Montreal Posts: 26 Drives: 2017 370Z DBP M6 Rep Power: 10	Somebody needs to tell the owner of this fine Z about this clutch pedal upgrade: https://www.youtube.com/watch?v=zxXAlsSyloo A wonderful choice of colour, might I add. Ryan @ RJM likes this.

03-15-2016, 02:39 AM	#404 (permalink)
R6MT Base Member Join Date: Nov 2015 Location: Portland, OR Age: 33 Posts: 5 Drives: 12 PW 370Z 6MT Sport Rep Power: 10	Just got my shipping confirmation today showing that I get mine Friday! Can't wait to install it this weekend. Much appreciated! Ryan @ RJM likes this.

03-15-2016, 07:07 AM	#405 (permalink)
brancky3 Track Member Join Date: Jun 2014 Location: Greer, SC Age: 37 Posts: 754 Drives: 14 370Z Gun Metallic Rep Power: 16	Received mine yesterday, will be installing tomorrow. Ryan @ RJM and Dbeckwith like this. __________________ 2014 Nissan 370z Gun Metallic 6-spd Test Pipes \| Nismo CBE \| Stillen Gen3 \| Swift springs \| Advanation Sway Bars \| RJM Clutch \| GTR DBA Premium Wheels

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Clutch pedal too soft/no feel? Remove the helper spring!	esfourteen	Engine & Drivetrain	560	12-31-2020 01:17 PM
Review: RJM AFP Clutch Pedal System	modme	Engine & Drivetrain	217	05-18-2020 08:59 AM
Clutch pedal feel	Zboy	Engine & Drivetrain	2	08-27-2012 09:43 PM
Review: 370z RJM AFP Clutch Pedal System	cdoxp800	Engine & Drivetrain	0	08-12-2012 12:57 PM

02-29-2016, 09:56 PM	#392 (permalink)
xdragus Base Member Join Date: Aug 2015 Location: toronto Posts: 47 Drives: '17 PW Nismo Rep Power: 10	Looking to purchase this but what proof do you have to back up your claims "Reduces or Eliminates the Concentric Slave Cylinder failures that are so common on these cars." on your website. Would this potentially conflict with the zspeed hd csc or z1 csc elimination kit? can they be combined?

03-02-2016, 10:08 PM	#395 (permalink)
xdragus Base Member Join Date: Aug 2015 Location: toronto Posts: 47 Drives: '17 PW Nismo Rep Power: 10	Just ordered. Thanks

03-06-2016, 11:11 PM	#397 (permalink)
N8GTOL Base Member Join Date: May 2010 Location: San Diego Posts: 228 Drives: and flies Rep Power: 22	Ryan, I finally placed my order! Can't wait to feel the difference with this mod. Even if I have to relearn how to shift the car after making due with the current setup for 5+ years it should be worth the wait.

03-08-2016, 06:36 AM	#398 (permalink)
Swindler Base Member Join Date: Oct 2013 Location: Central CA Age: 35 Posts: 219 Drives: 2014 370Z PW Manual Rep Power: 12	Just placed an order for this after reading through all 27 pages and everything on the RJM website. Can't wait, super excited for sure! I removed the clutch helper spring over a year ago and it was a huge improvement. However it is still tricky with that high engagement point. I hope this new pedal will be as good as it sounds, very excited.