RJM Clutch Pedal System for 370Z - Fully Customizable Clutch Feel & Stroke

jlo370z · 05-03-2014, 05:20 PM

Got mine today, cant wait to get it installed.

Ryan, thank you for the great service level you provide for your customers. I will recommend you to everyone I can.

onzedge · 05-03-2014, 05:37 PM

Quote:

Originally Posted by Ryan @ RJM

That's awesome news guys

I'm very happy to hear you both had successful installs and are enjoying the difference my product make in the overall feel of your cars

It really makes my day to read posts like these and makes all the long hours in the shop truly worth it

Ryan @ RJM · 05-04-2014, 07:46 AM

Quote:

Originally Posted by jlo370z

Got mine today, cant wait to get it installed.

Ryan, thank you for the great service level you provide for your customers. I will recommend you to everyone I can.

jlo370z, You're very welcome! Best of luck with the install and I'll look forward to hearing how you like it

Bummer · 05-06-2014, 07:56 PM

Mine got here yesterday but there was nobody available to sign for it, so it got picked up today, safe and sound.

Opened it up. Fondled the parts. Mmmmm. Pretty. Uh, mechanically speaking, of course.

I know what I'll be doing tomorrow afternoon.

Bummer · 05-08-2014, 11:05 PM

Things didn't work as planned, and I didn't get to the pedal assembly swap until today.

I'd rather rebuild an entire engine than wrench on three bolts under the dash. That being said the hardest part was taking the stock one out. Oh, and getting that wire tie threaded through that little hole. Installation itself was a breeze.

Still, all things considered not really all that hard. The instructions were thorough. I missed the blue plastic bumper until I was sitting around looking at the old assembly. I'll bet it's a lot easier to swap onto the new one on the bench. Still, that was my fault.

I am extremely happy with the change. I totally agree with everyone who said this is how it should have been all along.

Great product! Very good instructions. Timely delivery. Even though I hate working under the dash, I'm extremely glad I did it.

LukasC · 05-09-2014, 03:44 AM

Sub to this for at the end of summer new clutch/flywheel/z1 csc delete combo plus this! Ive always hated how jerky the stock clutch is and is impossible to launch really good every time

Bummer · 05-09-2014, 04:59 AM

Quote:

Originally Posted by LukasC

Sub to this for at the end of summer new clutch/flywheel/z1 csc delete combo plus this! Ive always hated how jerky the stock clutch is and is impossible to launch really good every time

I didn't have all that much trouble taking off from a stop, even robustly. My problem was the following shifts. Under power, shifts had a tendency to be quite jerky. This modification completely changed that.

LukasC · 05-09-2014, 12:37 PM

Quote:

Originally Posted by Bummer

I didn't have all that much trouble taking off from a stop, even robustly. My problem was the following shifts. Under power, shifts had a tendency to be quite jerky. This modification completely changed that.

What i mean is feathering the clutch on launch is hard when its like a light switch either totally engaged or totally disengaged. With 435whp it gets a little jumpy lol this mechanism gives more feathering space which is why i want it lol

Bummer · 05-10-2014, 04:05 AM

Quote:

Originally Posted by LukasC

What i mean is feathering the clutch on launch is hard when its like a light switch either totally engaged or totally disengaged. With 435whp it gets a little jumpy lol this mechanism gives more feathering space which is why i want it lol

Did you have no issues with ensuing shifts? I would think that with so much more HP to the ground you'd be nearly snapping the passenger's neck.

I certainly agree that you should see substantial improvement. I'll be quite surprised if you do not find this change to be a night and day sort of thing.

Ryan @ RJM · 05-10-2014, 11:20 AM

Quote:

Originally Posted by Bummer

Things didn't work as planned, and I didn't get to the pedal assembly swap until today.

I'd rather rebuild an entire engine than wrench on three bolts under the dash. That being said the hardest part was taking the stock one out. Oh, and getting that wire tie threaded through that little hole. Installation itself was a breeze.

Still, all things considered not really all that hard. The instructions were thorough. I missed the blue plastic bumper until I was sitting around looking at the old assembly. I'll bet it's a lot easier to swap onto the new one on the bench. Still, that was my fault.

I am extremely happy with the change. I totally agree with everyone who said this is how it should have been all along.

Great product! Very good instructions. Timely delivery. Even though I hate working under the dash, I'm extremely glad I did it.

Glad to hear everything went well on the install and you're enjoying the new pedal.

Its really hard to describe just how much better these cars feel with the redesigned pedal assembly installed and really needs to be experienced to be believed

Bummer · 05-10-2014, 09:29 PM

Quote:

Originally Posted by Ryan @ RJM

Glad to hear everything went well on the install and you're enjoying the new pedal.

I am indeed. Thank you.

Quote:

Originally Posted by Ryan @ RJM

Its really hard to describe just how much better these cars feel with the redesigned pedal assembly installed and really needs to be experienced to be believed

This is beyond a doubt true. Everyone with the manual transmission in their 370Z owes this to themselves.

onzedge · 05-10-2014, 11:06 PM

Quote:

Originally Posted by Bummer

I am indeed. Thank you.

This is beyond a doubt true. Everyone with the manual transmission in their 370Z owes this to themselves.

JARblue · 05-20-2014, 08:52 AM

Ryan, is there a way to adjust the pedal height without affecting the clutch rod position? I know the two pre-installed loose bolts (7/16") allow a large portion of the assembly including the pedal to slide up and down, but this directly impacts the position of the CMC rod. I have found that to have the rod horizontal, which I understand is how it needs to be, the pedal has to be lowered all the way down. It is even with the brake pedal and looks fine, but I'm finding the toe of my boots hit the upper arm of the pedal on occasion. TBH, I'm not exactly sure how the new pedal height compares to the stock pedal height.

Is there another way to adjust the pedal height? I ask because I will be installing a new CMC this week, so I'll be working in the vicinity if there's something I can do. If not, it's not really bothersome - I just happened to notice it a couple of times since the install.

Ryan @ RJM · 05-20-2014, 08:36 PM

Quote:

Originally Posted by JARblue

Ryan, is there a way to adjust the pedal height without affecting the clutch rod position? I know the two pre-installed loose bolts (7/16") allow a large portion of the assembly including the pedal to slide up and down, but this directly impacts the position of the CMC rod. I have found that to have the rod horizontal, which I understand is how it needs to be, the pedal has to be lowered all the way down. It is even with the brake pedal and looks fine, but I'm finding the toe of my boots hit the upper arm of the pedal on occasion. TBH, I'm not exactly sure how the new pedal height compares to the stock pedal height.

Is there another way to adjust the pedal height? I ask because I will be installing a new CMC this week, so I'll be working in the vicinity if there's something I can do. If not, it's not really bothersome - I just happened to notice it a couple of times since the install.

JARblue, you can independently move the height of the lower arm section up/down up to 3/4" by loosening the 3 bolt connection between the upper/lower arms allowing the arm to be "clocked" to a new angle and then tighten it back up again. Although the adjustment you mentioned above with the 2 bearing pre-load bolts is specifically just for aligning the clutch rod for a straight push of the linkage and not intended for height adjustment beyond leveling the rod.
Hope that helps a bit but I suspect what you're trying to do is raise the entire assembly more on the firewall which can't be done.

madwi · 05-21-2014, 12:44 AM

Quote:

Originally Posted by Ryan @ RJM

Glad to hear everything went well on the install and you're enjoying the new pedal.

Its really hard to describe just how much better these cars feel with the redesigned pedal assembly installed and really needs to be experienced to be believed

Not hard to describe at all... ******* awesome!

Ryan, I do not think I can add anything that has not been said already by others. All vendors should take note of how you operate. Great communication all the way through the whole transaction and a solid product.

P.S. Now that I bought mine, you really should be charging more

05-03-2014, 05:20 PM	#226 (permalink)
jlo370z Im a Fireball Join Date: Apr 2012 Location: Ill in noise Posts: 3,370 Drives: 11 370z Red 6spd Rep Power: 43426	Got mine today, cant wait to get it installed. Ryan, thank you for the great service level you provide for your customers. I will recommend you to everyone I can. onzedge likes this. __________________ ❝The Jlo370Z Build❞ 523HP \| 455 ftb tq \| 11.5 PSI \| 93 Octane *2017 Porsche 991.2 C4!l*

05-06-2014, 07:56 PM	#229 (permalink)
Bummer Premium Member Join Date: Mar 2012 Location: Indianapolis, IN Posts: 303 Drives: 13 370Z RTS SR M6 Rep Power: 50	Mine got here yesterday but there was nobody available to sign for it, so it got picked up today, safe and sound. Opened it up. Fondled the parts. Mmmmm. Pretty. Uh, mechanically speaking, of course. I know what I'll be doing tomorrow afternoon. onzedge and Ryan @ RJM like this. __________________ Steve

05-08-2014, 11:05 PM	#230 (permalink)
Bummer Premium Member Join Date: Mar 2012 Location: Indianapolis, IN Posts: 303 Drives: 13 370Z RTS SR M6 Rep Power: 50	Things didn't work as planned, and I didn't get to the pedal assembly swap until today. I'd rather rebuild an entire engine than wrench on three bolts under the dash. That being said the hardest part was taking the stock one out. Oh, and getting that wire tie threaded through that little hole. Installation itself was a breeze. Still, all things considered not really all that hard. The instructions were thorough. I missed the blue plastic bumper until I was sitting around looking at the old assembly. I'll bet it's a lot easier to swap onto the new one on the bench. Still, that was my fault. I am extremely happy with the change. I totally agree with everyone who said this is how it should have been all along. Great product! Very good instructions. Timely delivery. Even though I hate working under the dash, I'm extremely glad I did it. onzedge and Ryan @ RJM like this. __________________ Steve

05-20-2014, 08:52 AM	#238 (permalink)
JARblue A True Z Fanatic Join Date: Mar 2011 Location: Austin, TX Age: 43 Posts: 36,450 Drives: 11 Z34, 98 E36 M3 Rep Power: 2684440	Ryan, is there a way to adjust the pedal height without affecting the clutch rod position? I know the two pre-installed loose bolts (7/16") allow a large portion of the assembly including the pedal to slide up and down, but this directly impacts the position of the CMC rod. I have found that to have the rod horizontal, which I understand is how it needs to be, the pedal has to be lowered all the way down. It is even with the brake pedal and looks fine, but I'm finding the toe of my boots hit the upper arm of the pedal on occasion. TBH, I'm not exactly sure how the new pedal height compares to the stock pedal height. Is there another way to adjust the pedal height? I ask because I will be installing a new CMC this week, so I'll be working in the vicinity if there's something I can do. If not, it's not really bothersome - I just happened to notice it a couple of times since the install. __________________ 2011 370Z 6MT Sport Gun Metallic \| ARC \| CJM \| Ecutek \| FI \| Fujimura \| R2C \| SPL \| Stillen \| TWM \| Z1 \| ZSpeed \|

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Clutch pedal too soft/no feel? Remove the helper spring!	esfourteen	Engine & Drivetrain	560	12-31-2020 01:17 PM
Review: RJM AFP Clutch Pedal System	modme	Engine & Drivetrain	217	05-18-2020 08:59 AM
Clutch pedal feel	Zboy	Engine & Drivetrain	2	08-27-2012 09:43 PM
Review: 370z RJM AFP Clutch Pedal System	cdoxp800	Engine & Drivetrain	0	08-12-2012 12:57 PM

05-09-2014, 03:44 AM	#231 (permalink)
LukasC Track Member Join Date: Apr 2011 Location: San Antonio, Tx Posts: 664 Drives: 11 Stillen SC Bl M6 Rep Power: 17	Sub to this for at the end of summer new clutch/flywheel/z1 csc delete combo plus this! Ive always hated how jerky the stock clutch is and is impossible to launch really good every time