Change engine oil step by step

kenchan · 07-07-2014, 10:32 PM

Quote:

Originally Posted by 2004YZFR1

Brake cleaner is a good solvent and not very expensive. Dries without leaving a residue also. Try it some time.

a tad better is RC car motor spray/nitro cleaner. they literally leave no smell or residue behind where as brake cleaner leaves behind stench..

but i too use brake cleaner to wipe up my drain pan.

stivs370z · 07-16-2014, 12:16 PM

Quote:

Originally Posted by 2004YZFR1

Nice video and good quality also, I would suggest a couple of things for the next change that might help.

1. Use your torque wrench for your oil filter and your drain plug.

2. Use some brake cleaner or contact cleaner to get the last bit of oil residue off.

3. Lower car to get a accurate measure on the dip stick.

4. Crack a beer or two after you finish to admire your car and for saving money not having the dealer do it.

Nice job and thanks for sharing.

Thank you.

kenchan · 07-16-2014, 12:34 PM

uhh... i seriously do NOT use a torque wrench for my filter nor plug. lol

ive used it on my diff and tranny plugs..

JARblue · 07-16-2014, 12:44 PM

Quote:

Originally Posted by kenchan

uhh... i seriously do NOT use a torque wrench for my filter nor plug. lol

ive used it on my diff and tranny plugs..

I use it on the drain plug... too easy for me not to use it. But how would you use it on the oil filter? I know the K&N has the nut on the end you could use, but I don't use K&N filters.

kenchan · 07-16-2014, 12:49 PM

i think you just tighten it snug and make a click noise in your mouth.

Mitco39 · 07-16-2014, 12:53 PM

Don't most specify something like hand tight then 1/2 a turn more?

aszyd · 07-16-2014, 01:34 PM

Quote:

Originally Posted by Mitco39

Don't most specify something like hand tight then 1/2 a turn more?

That sounds about right. I know with the oil filters, I tighten until it is almost too difficult to remove by hand. That way I know it's not going to rattle loose. I have been stuck with a torqued on filter and no wrench. It's not fun having to jam a screw driver through the filter to get it off.

Drain plugs are the same, but with tools. Just tight enough to need a little torque to take them off. It's not necessary to put them at 80 ft/lbs.

kenchan · 07-16-2014, 01:41 PM

yah, snug, but not super tight. that comes from experience though.

Limeybastard · 07-16-2014, 06:15 PM

Quote:

Originally Posted by aszyd

That sounds about right. I know with the oil filters, I tighten until it is almost too difficult to remove by hand. That way I know it's not going to rattle loose. I have been stuck with a torqued on filter and no wrench. It's not fun having to jam a screw driver through the filter to get it off.

Drain plugs are the same, but with tools. Just tight enough to need a little torque to take them off. It's not necessary to put them at 80 ft/lbs.

That occured on my first oil change, the factory had over tightened it then quart a turn. I only every just hand tighten.

Very messy.

djc119 · 07-25-2014, 10:30 AM

Quote:

Originally Posted by aszyd

... It's not fun having to jam a screw driver through the filter to get it off...

I had this problem on every NEW car I've ever bought.

4988 mi. on the NEW Z, so I'll find out when I change the oil; as soon as I get a set of low ramps.

BTW- Anyone selling low ramps aroung the NY area?

JARblue · 07-25-2014, 10:50 AM

I had to use a pair of large channel locks the first two changes on the Z (last dealer serviced filter and my first DIY filter). I now know exactly how much to hand tighten: not too much

kenchan · 07-25-2014, 11:57 AM

Quote:

Originally Posted by JARblue

I had to use a pair of large channel locks the first two changes on the Z (last dealer serviced filter and my first DIY filter). I now know exactly how much to hand tighten: not too much

yah, it's not like its going to vibrate off the engine once it's snug.

Plasmite · 07-25-2014, 02:31 PM

Quote:

Originally Posted by aszyd

That sounds about right. I know with the oil filters, I tighten until it is almost too difficult to remove by hand. That way I know it's not going to rattle loose. I have been stuck with a torqued on filter and no wrench. It's not fun having to jam a screw driver through the filter to get it off.

Drain plugs are the same, but with tools. Just tight enough to need a little torque to take them off. It's not necessary to put them at 80 ft/lbs.

That sounds more like they mated it up to the surface without lubing the o-ring first. You can put a filter on tight with a 1/4 turn and have to plasma cut it off if someone didn't lube the mating surfaces first.

I am on my 10 billionth oil change (HD apprentice) and it is STILL something that drives me batshi+ crazy lol

1325 · 07-25-2014, 06:33 PM

Hand tighten the oil filter and for removal, nothing does a better job than using oil filter pliers. Its teeth with firmly grasp the filter and loosen with ease.

aszyd · 07-25-2014, 09:48 PM

Quote:

Originally Posted by Plasmite

That sounds more like they mated it up to the surface without lubing the o-ring first. You can put a filter on tight with a 1/4 turn and have to plasma cut it off if someone didn't lube the mating surfaces first.

I am on my 10 billionth oil change (HD apprentice) and it is STILL something that drives me batshi+ crazy lol

That's very possible. How do you feel about filling the filter with oil before putting it on the car? On the new Focus, the filter faces downwards, so it was quite easy to do the pre-fill, but with these sideways mounted filters, I don't know how to do it without making a mess. So I usually don't...

Quote:

Originally Posted by 1325

Hand tighten the oil filter and for removal, nothing does a better job than using oil filter pliers. Its teeth with firmly grasp the filter and loosen with ease.

Back when I had my first car, I would let Walmart do the oil changes. They once "gifted" me a filter wrench. When I got home after a change, I noticed that the hood was bulging oddly on one side. When I opened it up, there was a filter wrench just sitting there

. I think my father has it now, I'm not sure.

07-16-2014, 12:49 PM	#20 (permalink)
kenchan A True Z Fanatic Join Date: Aug 2009 Location: N/A Posts: 76,801 Drives: N/A Rep Power: 141521	i think you just tighten it snug and make a click noise in your mouth. JARblue and carmelvalleyZ like this.

07-16-2014, 12:53 PM	#21 (permalink)
Mitco39 A True Z Fanatic Join Date: Aug 2012 Location: Edmonton Alberta Canada Posts: 2,089 Drives: 40th 370z Rep Power: 132	Don't most specify something like hand tight then 1/2 a turn more? Plasmite likes this. __________________ 2007 Chevy Duramax - EFILive Tuned By Me 2010 40th W/ Nav - Boosted Performance - UpRev Tuned By Me The Mrs. Ride -2012 335XI N55 BMW - Cobb Tuned By Me, Built by her My Build --> http://www.the370z.com/members-370z-...39s-build.html

07-25-2014, 10:50 AM	#26 (permalink)
JARblue A True Z Fanatic Join Date: Mar 2011 Location: Austin, TX Age: 43 Posts: 36,450 Drives: 11 Z34, 98 E36 M3 Rep Power: 2684440	I had to use a pair of large channel locks the first two changes on the Z (last dealer serviced filter and my first DIY filter). I now know exactly how much to hand tighten: not too much __________________ 2011 370Z 6MT Sport Gun Metallic \| ARC \| CJM \| Ecutek \| FI \| Fujimura \| R2C \| SPL \| Stillen \| TWM \| Z1 \| ZSpeed \|

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[FOR SALE] WORK Gnosis GS4 Step Lip 20 inch Step Lip	Storm	Parts for sale (Private Classifieds)	30	03-20-2014 02:02 PM
my first step -_-	elia_ebyss	Forced Induction	45	09-13-2013 11:33 AM
WOT box 2-step	NIZZING	Forced Induction	14	02-14-2013 11:32 PM
Red GT-R Push Start Button Installation Step by Step~~~Super easy!	cycy89	DIY Section (Do-It-Yourself)	25	03-31-2012 11:52 PM
Looking to step up from the Yaris	Kiteless	New Forum Member	0	02-06-2012 08:35 PM

07-16-2014, 12:34 PM	#18 (permalink)
kenchan A True Z Fanatic Join Date: Aug 2009 Location: N/A Posts: 76,801 Drives: N/A Rep Power: 141521	uhh... i seriously do NOT use a torque wrench for my filter nor plug. lol ive used it on my diff and tranny plugs..

07-16-2014, 01:41 PM	#23 (permalink)
kenchan A True Z Fanatic Join Date: Aug 2009 Location: N/A Posts: 76,801 Drives: N/A Rep Power: 141521	yah, snug, but not super tight. that comes from experience though.

07-25-2014, 06:33 PM	#29 (permalink)
1325 Enthusiast Member Join Date: Jul 2010 Location: Florida Posts: 287 Drives: 10 370Z BLK 6M Rep Power: 15	Hand tighten the oil filter and for removal, nothing does a better job than using oil filter pliers. Its teeth with firmly grasp the filter and loosen with ease.