Need Help with H&R 10 mm DRS Spacers

40 to 332 · 05-05-2014, 12:21 PM

Looking to install H&R DRS 10 mm wheel spacers, and am confused by a note on the back-side of the instructions that indicates for these specific spacers that "maximum hub height" cannot be greater than 10 mm. There is no point of reference provided so I'm not sure where the measurement is to be taken from … from the face of the brake rotor to the front edge of the hub??? … with the spacer on or off??? I'm completely confused. I checked the H&R website, but it was not especially helpful … and there is no link to contact them directly. I'm not only confused about where to take the measurement, but also why the note only applies to the 10 mm DRS spacers. I must be missing something (???). Help! Thanks.

DR_ · 05-05-2014, 01:06 PM

Probably means they don't want you to put a spacer larger than 10mm with the included wheel bolts.

40 to 332 · 05-05-2014, 01:51 PM

I think that I figured it out. The maximum hub height refers to the maximum distance that the stock hub can extend without the spacer bottoming out on the leading edge of the hub such that the spacer will not fit flush. I suspect that it's not an issue with the wider spacers since there's enough clearance because of the added width that the spacer will not bottom out. Not sure if the 10 mm spacers have ever proven to be problematic in terms of fit on the Z. I'll simply have to check the hub height when I pull the wheels off.

05-05-2014, 12:21 PM	#1 (permalink)
40 to 332 Enthusiast Member Join Date: Apr 2013 Location: Kimberley, BC, CANADA Posts: 447 Drives: 13 370Z BS M6 Sport Rep Power: 439	Need Help with H&R 10 mm DRS Spacers Looking to install H&R DRS 10 mm wheel spacers, and am confused by a note on the back-side of the instructions that indicates for these specific spacers that "maximum hub height" cannot be greater than 10 mm. There is no point of reference provided so I'm not sure where the measurement is to be taken from … from the face of the brake rotor to the front edge of the hub??? … with the spacer on or off??? I'm completely confused. I checked the H&R website, but it was not especially helpful … and there is no link to contact them directly. I'm not only confused about where to take the measurement, but also why the note only applies to the 10 mm DRS spacers. I must be missing something (???). Help! Thanks.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[FOR SALE] Z1 20mm Spacers, H&R 15mm spacers	black_sedan	Parts for sale (Private Classifieds)	6	01-06-2014 11:08 AM
[FOR SALE] 30mm Ichiba V2 Hubcentric Wheel Spacers with Hub Centric Rings / Built In spacers	HenryLee	Parts for sale (Private Classifieds)	4	09-20-2013 03:31 PM
[WTB] Looking to trade 15mm and 20mm drs H&R TRAK+ spacers for drm spacers	Amelio1217	Parts for sale (Private Classifieds)	14	06-05-2013 02:04 PM
[FOR SALE] Two 25mm spacers with studs ,two 10mm spacers , socal.	Chaddrift	Parts for sale (Private Classifieds)	2	02-18-2013 02:20 PM
Fs: H&r 20mm rear spacers / 15mm front spacers	xbigb4ller69z	Parts for sale (Private Classifieds)	25	12-10-2010 01:20 PM

05-05-2014, 01:06 PM	#2 (permalink)
DR_ Track Member Join Date: Jul 2009 Location: Dallas Posts: 981 Drives: Touring/Sport M6 PG Rep Power: 17	Probably means they don't want you to put a spacer larger than 10mm with the included wheel bolts.

05-05-2014, 01:51 PM	#3 (permalink)
40 to 332 Enthusiast Member Join Date: Apr 2013 Location: Kimberley, BC, CANADA Posts: 447 Drives: 13 370Z BS M6 Sport Rep Power: 439	I think that I figured it out. The maximum hub height refers to the maximum distance that the stock hub can extend without the spacer bottoming out on the leading edge of the hub such that the spacer will not fit flush. I suspect that it's not an issue with the wider spacers since there's enough clearance because of the added width that the spacer will not bottom out. Not sure if the 10 mm spacers have ever proven to be problematic in terms of fit on the Z. I'll simply have to check the hub height when I pull the wheels off.