Nissan 370Z Forum  

DIY: Upgrade Component Speakers from BOSE

Without running new wiring or replacing your head unit. Purchase 6.5” Components with crossovers, amplifier of your choice, and some amp wiring. Install fuse block and run power wire for

Go Back   Nissan 370Z Forum > Nissan 370Z Tech Area > DIY Section (Do-It-Yourself)


Like Tree26Likes

Reply
 
LinkBack Thread Tools Display Modes
Old 02-10-2014, 12:20 AM   #1 (permalink)
Track Member
 
SuperDave's Avatar
 
Join Date: May 2013
Location: Manteca, Nor-Cal
Posts: 691
Drives: My Z Daily
Rep Power: 13
SuperDave is a splendid one to beholdSuperDave is a splendid one to beholdSuperDave is a splendid one to beholdSuperDave is a splendid one to beholdSuperDave is a splendid one to beholdSuperDave is a splendid one to beholdSuperDave is a splendid one to behold
Default DIY: Upgrade Component Speakers from BOSE

Without running new wiring or replacing your head unit.

Purchase 6.5” Components with crossovers, amplifier of your choice, and some amp wiring.

Install fuse block and run power wire for amp (see other DIY’s). I went under the passenger seat for this install, as it is a good central location between the battery and where all the wires are for the BOSE Amp.

Remove carpet, plastic piece, and black foam (under strut tower bar, pull hard) from the trunk. You can also tap one of the unused bolts under here near the passenger side for the ground for your amp. Run it down through the passenger side under the plastic interior piece then pop it through the carpet, into your amp.

Remove two bolts and two nuts from the BOSE amp, flip it over, and unplug the two cannon plugs.
Line in to BOSE Amp, strip back and tap (do not cut completely):
  • White for Amp Remote – run it down to the amp in the same path as your ground wire.
Line in to BOSE Amp, clip completely and splice into RCA Connectors:
  • Pink is Front Left +
  • Blue is Front Left –
  • Red is Front Right +
  • Green is Front Right –
    Make sure they are long enough to go from the BOSE amp plug down to your amp.
Line out from amp back to speakers, clip completely, splice into standard red and black speaker wire, and label:
  • Purple and Blue pair is Front Left Speaker
  • Light Green and Grey pair is Front Left Tweeter
  • Orange and Green pair is Front Right Speaker
  • Black and White pair is Front Right Tweeter
    These don’t need to be as long, since you will put your crossovers in this area.
Install your components. At the speakers, just clip and splice the factory wiring into standard connectors. (See other DIY’s). FYI I made my own 6x9 to 6.5” adapter plate using the BOSE speaker mounts and about $6 in plastic with a dremel.

Connect:
  • Newly spliced RCA connectors into amp front left and right channel.
  • Run two pairs of speaker wire from the BOSE amp area down to your amp, connect to amp left and right output. Back near the BOSE amp, connect these wires to your crossovers input.
  • Connect the newly spliced speaker and tweeter wires from the step above into your Crossovers output. Secure your crossovers with double stick tape.
Reinstall the two cannon plugs back into the BOSE amp and reinstall the amp with the two nuts and two bolts. This keeps your BOSE sub thumping until your next paycheck when you have funds to upgrade it.

Double check all connections, install amp fuse, and crank it up!

Check that everything works, put your interior pieces back together, and secure your amp.

Sorry for the lack of pics. I did not really intend to make a DIY out of it when I was doing it, but I have gotten a lot of requests to write it up, so here it is. If you have any questions, I will do my best to answer them here. I also had a witness to the install, thanks for the use of your garage CBTech.
chubbs, Knio, zakimak and 10 others like this.

Last edited by SuperDave; 02-10-2014 at 02:15 AM.
SuperDave is offline   Reply With Quote
Old 02-10-2014, 12:27 AM   #2 (permalink)
A True Z Fanatic
 
Cbtech's Avatar
 
Join Date: Feb 2013
Location: Sacramento, CA
Posts: 1,372
Drives: 40th Anniversary
Rep Power: 15
Cbtech has much to be proud ofCbtech has much to be proud ofCbtech has much to be proud ofCbtech has much to be proud ofCbtech has much to be proud ofCbtech has much to be proud ofCbtech has much to be proud ofCbtech has much to be proud ofCbtech has much to be proud ofCbtech has much to be proud of
Default

Effing MONEY! Well done!
SuperDave likes this.
__________________
Cbtech is offline   Reply With Quote
Old 02-10-2014, 10:57 AM   #3 (permalink)
6/2/80 - 9/29/14 - RIP Lukas
 
zakimak's Avatar
 
Join Date: Jun 2011
Location: Ottawa, Ontario
Posts: 450
Drives: ZR; Q45; VTR1K, GT65
Rep Power: 17
zakimak has a reputation beyond reputezakimak has a reputation beyond reputezakimak has a reputation beyond reputezakimak has a reputation beyond reputezakimak has a reputation beyond reputezakimak has a reputation beyond reputezakimak has a reputation beyond reputezakimak has a reputation beyond reputezakimak has a reputation beyond reputezakimak has a reputation beyond reputezakimak has a reputation beyond repute
Default

Quote:
Originally Posted by Cbtech View Post
Effing MONEY! Well done!
Agreed... Not everyone can afford or want complete tear down/build up. Basically bypassing the amp's output and using existing wiring. Cheap, effective and with minimal disruption. Good job
Cbtech, Luciano13 and SuperDave like this.
__________________
What doesn't kill you might make you a cripple so chose wisely.

Free Stuff for Premium Members - Yeah Really
zakimak is offline   Reply With Quote
Old 02-10-2014, 09:39 PM   #4 (permalink)
Track Member
 
SuperDave's Avatar
 
Join Date: May 2013
Location: Manteca, Nor-Cal
Posts: 691
Drives: My Z Daily
Rep Power: 13
SuperDave is a splendid one to beholdSuperDave is a splendid one to beholdSuperDave is a splendid one to beholdSuperDave is a splendid one to beholdSuperDave is a splendid one to beholdSuperDave is a splendid one to beholdSuperDave is a splendid one to behold
Default

I found some extremely useful pictures

Custom 6x9" to 6.5" adapter plate using the BOSE mount:


How to sit in your trunk while looking at wiring diagrams on a tablet:
Attached Images
File Type: jpg 1.jpg (118.5 KB, 1986 views)
File Type: jpg 2.jpg (116.8 KB, 1961 views)
Fountainhead and Leroydsouza like this.
SuperDave is offline   Reply With Quote
Old 02-14-2014, 10:45 PM   #5 (permalink)
A True Z Fanatic
 
Riptide67's Avatar
 
Join Date: Jul 2013
Location: Oak Harbor, WA
Age: 37
Posts: 1,610
Drives: 09 Nismo #0483 PW
Rep Power: 69
Riptide67 has a reputation beyond reputeRiptide67 has a reputation beyond reputeRiptide67 has a reputation beyond reputeRiptide67 has a reputation beyond reputeRiptide67 has a reputation beyond reputeRiptide67 has a reputation beyond reputeRiptide67 has a reputation beyond reputeRiptide67 has a reputation beyond reputeRiptide67 has a reputation beyond reputeRiptide67 has a reputation beyond reputeRiptide67 has a reputation beyond repute
Default

Ill be using this in the future!
SuperDave likes this.
__________________
2009 Nismo 370Z and 1975 Datsun 280Z 2+2 - PNW_INC - Legacy_Ohana
Follow me on Instagam @s3zero_z3four
Riptide67 is offline   Reply With Quote
Old 02-15-2014, 04:30 AM   #6 (permalink)
A True Z Fanatic
 
RonRizz's Avatar
 
Join Date: Aug 2011
Location: Pine grove, Pa
Posts: 2,136
Drives: 2 feet, 3 pedals
Rep Power: 6775
RonRizz has a reputation beyond reputeRonRizz has a reputation beyond reputeRonRizz has a reputation beyond reputeRonRizz has a reputation beyond reputeRonRizz has a reputation beyond reputeRonRizz has a reputation beyond reputeRonRizz has a reputation beyond reputeRonRizz has a reputation beyond reputeRonRizz has a reputation beyond reputeRonRizz has a reputation beyond reputeRonRizz has a reputation beyond repute
Default

Nice work! well written DIY.
SuperDave likes this.
__________________
P99rs Head Unit--- Amps- 2 Pioneer Prs800d --- Zapco ST1000MX---Zapco ST-4XSQ---- SI BM mk5 Subs---SI TM65v2 Midbass--- SI M3 mids--- SI M25 xbl2 tweeters ----- 2016 MECA street class 3rd place at world finals
RonRizz is offline   Reply With Quote
Old 04-23-2014, 04:35 AM   #7 (permalink)
Premium Member Bitches
 
DEpointfive0's Avatar
 
Join Date: Jan 2012
Location: SoCal
Posts: 14,824
Drives: a lot
Rep Power: 17151
DEpointfive0 has a reputation beyond reputeDEpointfive0 has a reputation beyond reputeDEpointfive0 has a reputation beyond reputeDEpointfive0 has a reputation beyond reputeDEpointfive0 has a reputation beyond reputeDEpointfive0 has a reputation beyond reputeDEpointfive0 has a reputation beyond reputeDEpointfive0 has a reputation beyond reputeDEpointfive0 has a reputation beyond reputeDEpointfive0 has a reputation beyond reputeDEpointfive0 has a reputation beyond repute
Default

Hey Jew

How do I connect just a sub using this "J" method? (Just tell me what to buy, lol)
SuperDave likes this.
__________________
Do YOU want to know what/where I got my username from?
( Click to show/hide )
DEpointfive0 is offline   Reply With Quote
Old 04-23-2014, 05:11 PM   #8 (permalink)
Track Member
 
SuperDave's Avatar
 
Join Date: May 2013
Location: Manteca, Nor-Cal
Posts: 691
Drives: My Z Daily
Rep Power: 13
SuperDave is a splendid one to beholdSuperDave is a splendid one to beholdSuperDave is a splendid one to beholdSuperDave is a splendid one to beholdSuperDave is a splendid one to beholdSuperDave is a splendid one to beholdSuperDave is a splendid one to behold
Default

The "J" method would be to first wait for a sale. Then clip coupons even though they say, "not valid in combination with any other offer". Then ask to speak to a manager...
DEpointfive0 and Cbtech like this.
SuperDave is offline   Reply With Quote
Old 04-23-2014, 05:59 PM   #9 (permalink)
Track Member
 
SuperDave's Avatar
 
Join Date: May 2013
Location: Manteca, Nor-Cal
Posts: 691
Drives: My Z Daily
Rep Power: 13
SuperDave is a splendid one to beholdSuperDave is a splendid one to beholdSuperDave is a splendid one to beholdSuperDave is a splendid one to beholdSuperDave is a splendid one to beholdSuperDave is a splendid one to beholdSuperDave is a splendid one to behold
Default

But seriously though, same concept, just cut the rear line in to the bose amp, splice into rca cables, into your new amp, and cut the sub line out from the bose amp. Splice output from your new amp into the sub line out that you cut from the bose amp. Or, since it's close enough, run speaker wire directly from your new amp out to your new sub.
SuperDave is offline   Reply With Quote
Old 05-29-2014, 01:35 PM   #10 (permalink)
Track Member
 
Silly Rabbit's Avatar
 
Join Date: Sep 2013
Location: Brookston, IN
Age: 54
Posts: 683
Drives: '12 PW Touring Sport
Rep Power: 619
Silly Rabbit has a reputation beyond reputeSilly Rabbit has a reputation beyond reputeSilly Rabbit has a reputation beyond reputeSilly Rabbit has a reputation beyond reputeSilly Rabbit has a reputation beyond reputeSilly Rabbit has a reputation beyond reputeSilly Rabbit has a reputation beyond reputeSilly Rabbit has a reputation beyond reputeSilly Rabbit has a reputation beyond reputeSilly Rabbit has a reputation beyond reputeSilly Rabbit has a reputation beyond repute
Default

I have the bose with nav. If I want to add a sub and keep the rest factory. Not replacing speakers and not clipping any lines to the bose amp. Will this work?

-Add amp with power, fuse and ground
-Tap white line before bose amp and connect to remote in on sub amp
-Tap (4) L/R line-in lines before bose amp
- Connect tapped lines to LOC
- Connect RCA lines from LOC to sub amp
- Connect sub amp to subwoofer


Can a simpler passive LOC like THIS be used?


Edit - Some more reading and I get the idea that I want to use a LC2i and connect it using the sky blue and violet lines (9&14) coming out of the bose amp instead of the lines going into the amp. Correct?

Confused - Now I'm reading that it is better to use the red and green lines (hi-level) from the bose sub amp to the bose sub, it will provide a better feed than the blue and violet lines (low level).

Last edited by Silly Rabbit; 05-29-2014 at 02:51 PM.
Silly Rabbit is offline   Reply With Quote
Old 05-30-2014, 08:27 AM   #11 (permalink)
Base Member
 
merkil's Avatar
 
Join Date: Oct 2013
Location: Brantford, Ontario
Posts: 63
Drives: 2011 370z
Rep Power: 12
merkil is a name known to allmerkil is a name known to allmerkil is a name known to allmerkil is a name known to allmerkil is a name known to allmerkil is a name known to all
Default DIY: Upgrade Component Speakers from BOSE

Can this sort of method be used to replace the smaller speakers behind the seats?



Sent from my iPhone using Tapatalk

Last edited by merkil; 05-30-2014 at 09:21 AM.
merkil is offline   Reply With Quote
Old 06-13-2014, 02:30 PM   #12 (permalink)
Track Member
 
SuperDave's Avatar
 
Join Date: May 2013
Location: Manteca, Nor-Cal
Posts: 691
Drives: My Z Daily
Rep Power: 13
SuperDave is a splendid one to beholdSuperDave is a splendid one to beholdSuperDave is a splendid one to beholdSuperDave is a splendid one to beholdSuperDave is a splendid one to beholdSuperDave is a splendid one to beholdSuperDave is a splendid one to behold
Default

Quote:
Originally Posted by merkil View Post
Can this sort of method be used to replace the smaller speakers behind the seats?



Sent from my iPhone using Tapatalk
Yes, they are like 3" mids. Just splice the rear wires instead of the fronts (wiring schematic in service manual).
SuperDave is offline   Reply With Quote
Old 06-13-2014, 02:31 PM   #13 (permalink)
Track Member
 
SuperDave's Avatar
 
Join Date: May 2013
Location: Manteca, Nor-Cal
Posts: 691
Drives: My Z Daily
Rep Power: 13
SuperDave is a splendid one to beholdSuperDave is a splendid one to beholdSuperDave is a splendid one to beholdSuperDave is a splendid one to beholdSuperDave is a splendid one to beholdSuperDave is a splendid one to beholdSuperDave is a splendid one to behold
Default

Quote:
Originally Posted by Silly Rabbit View Post
I have the bose with nav. If I want to add a sub and keep the rest factory. Not replacing speakers and not clipping any lines to the bose amp. Will this work?

-Add amp with power, fuse and ground
-Tap white line before bose amp and connect to remote in on sub amp
-Tap (4) L/R line-in lines before bose amp
- Connect tapped lines to LOC
- Connect RCA lines from LOC to sub amp
- Connect sub amp to subwoofer


Can a simpler passive LOC like THIS be used?


Edit - Some more reading and I get the idea that I want to use a LC2i and connect it using the sky blue and violet lines (9&14) coming out of the bose amp instead of the lines going into the amp. Correct?

Confused - Now I'm reading that it is better to use the red and green lines (hi-level) from the bose sub amp to the bose sub, it will provide a better feed than the blue and violet lines (low level).
Your original idea should work. I would splice the signal lines into the amp, that way you are tapping the signal from the head unit before the bose components come into play with their weird ohmage.
SuperDave is offline   Reply With Quote
Old 03-28-2015, 03:23 PM   #14 (permalink)
Base Member
 
Join Date: Apr 2014
Location: Ft.Lauderdale
Posts: 5
Drives: 09' Nissan 370 PW MT
Rep Power: 11
PoonSlayer is on a distinguished road
Default In need of an audio genie!..

-2009 Bose w/ Nav-

Tapped wires before bose amp for LOC.

Installed two amps, one for sub, and another for a set of additional component speakers.

Everything went smooth, but now for some reason, when Remote Switch On is connected my factory bose speakers work 10% of the time. But added components always work. When i disconnect Remote Switch On for amps, factory bose system works fine.

Any help/tips would be greatly appreciated!

Last edited by PoonSlayer; 03-29-2015 at 09:42 AM.
PoonSlayer is offline   Reply With Quote
Old 08-12-2015, 04:28 PM   #15 (permalink)
Base Member
 
Join Date: Mar 2015
Location: ohio
Posts: 10
Drives: 370z black roadster
Rep Power: 10
roadsterblack is on a distinguished road
Default any regrets?

Any regrets after doing this amp and components install with existing bose system / wiring? I'm about to follow your lead.

Thanks,
roadsterblack is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
To those with Polk DB6501 Component Speakers... bebenegro Audio & Video 17 05-19-2016 11:11 AM
Adapter for the front door component speakers? .c2 Audio & Video 5 09-06-2012 04:16 PM
[FOR SALE] MB Quart QS216 component speakers davencp33 Parts for sale (Private Classifieds) 0 05-09-2012 11:55 AM
Component Speakers - Where does the Crossover go?? Fatalsports Audio & Video 7 05-05-2011 02:42 AM
Front 6.5 component speakers Brands - Hertz 37Z Audio & Video 9 05-12-2010 10:07 PM


All times are GMT -5. The time now is 12:11 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO 3.6.0 PL2