DIY: Interior LED Color Change

DIGItonium · 04-30-2010, 01:51 AM

1) Pry switch assembly from trim panel.

2) Pry back cover from all sides.

3) There are two 0805 size LEDs to replace.

4) Complete! Be sure to follow window reset procedure.

DIGItonium · 05-23-2010, 01:42 AM

*** DISCONNECT (-) BATTERY CABLE FIRST AND WAIT A FEW MINUTES! ***

1. Pop off the screw covers on each side of the steering column to reveal the security torx screws. The best tool to use to remove the screws is this socket with the T30 security torx.

2. Pull the airbag unit, but be careful with the airbag and control cables. Release the steering wheel control cable harness. Pull the green ground wire. Use a 7mm wrench to remove the nut holding the wires. Each control has two screws to remove, and then simply pop it off towards the back end.

3. Use 0805 LEDs (8 total) to change the color of the switch panel.

4. Completed modification. Resistor change is not necessary as the illumination is more than adequate for night viewing.

theDreamer · 05-29-2010, 09:43 PM

Digi, do you plan on doing the triple gauge cluster over the center console?
I know it will require removing I think the dash as some have stated, but you would be the first at doing a full DIY(ish) on the forum.

DIGItonium · 05-30-2010, 01:36 PM

Quote:

Originally Posted by theDreamer

Digi, do you plan on doing the triple gauge cluster over the center console?

I'm holding off on this mod because I may end up getting aftermarket gauges instead. However, 2theextreme is going to ship me his gauges for the mod work so I'll post the DIY for his gauges. Black Cat Custom will be making the custom gauge faces.

XwChriswX · 05-30-2010, 04:22 PM

Digi, you really need to sloooow down lol I haven't even gotten the Driver's side door done, and your throwing all these new ideas at me! LoL

DIGItonium · 05-31-2010, 03:04 AM

Bump... updated DIY: Interior LED Color Change

Boost_lee · 05-31-2010, 03:12 AM

Digitonium - you do outstanding work, love this DIY

DIGItonium · 05-31-2010, 03:23 AM

Quote:

Originally Posted by Boost_lee

Digitonium - you do outstanding work, love this DIY

Thanks!

It was tedious, but quite worth it.

gromano · 06-10-2010, 12:31 AM

Hey Digitonium,
Nice mods!!
I wanna do the mirror/visor light conversion to LED!!!!
I got no idea how to string the LED's together like you did. And Im not sure on the sizing of them either...
Do you know if any of the bulbs shown on this site would fit?
http://www.led-online.com.au/index.p...mart&Itemid=37
Keeping in mind Im in Australia!
Figured you would help with sizing and Volts etc

Want some for the map lights/ambient lights too but dont know what to use.
Hate having red lights in my sexy blue car! hahaha
Thanks for your help

farmosh203 · 06-11-2010, 01:18 PM

That's really impressive you had the balls to take everything apart like that. Soldering anything above an 0402 size is no problem but I can't imagine taking my car apart and putting it back together like that.

I'm still trying to think of ideas on what I could do to my car using a microcontroller.

DIGItonium · 06-11-2010, 02:02 PM

Quote:

Originally Posted by gromano

Hey Digitonium,
Nice mods!!
I wanna do the mirror/visor light conversion to LED!!!!
I got no idea how to string the LED's together like you did. And Im not sure on the sizing of them either...
Do you know if any of the bulbs shown on this site would fit?
http://www.led-online.com.au/index.p...mart&Itemid=37
Keeping in mind Im in Australia!
Figured you would help with sizing and Volts etc

Want some for the map lights/ambient lights too but dont know what to use.
Hate having red lights in my sexy blue car! hahaha
Thanks for your help

Hello and thanks!

I honestly do not know about the bulb sizing and type. You can measure the bulbs and approximate the size of bulbs available on the website. If the info is not available, you can call them in and provide the measurements so you can get the bulb closest to your application. It's clip in, so you should have some flexibility.

DIGItonium · 06-11-2010, 02:08 PM

Quote:

Originally Posted by farmosh203

That's really impressive you had the balls to take everything apart like that. Soldering anything above an 0402 size is no problem but I can't imagine taking my car apart and putting it back together like that.

I'm still trying to think of ideas on what I could do to my car using a microcontroller.

Disassembly isn't too bad. The most tedious is desoldering the rotary switches for the HVAC and lining it back up through the PCB. The gauge cluster removal isn't too bad after doing it the first time.

This is going to require quite a bit of spaghetti wiring and masking of original pads. You can get 4-pin PLCC2 RGB LEDs. One pin is ground, and the other is positive for each color. Wire all the LEDs to your microcontroller/driver circuit. I guess you can program roughly 255 shades for each color. If you can pull this off, you'll be the LED god.

CBRich · 07-21-2010, 02:28 PM

SUBscribing. I need to get on this.

Joka4411 · 09-01-2010, 11:12 PM

WoW where do you get the guts to tryout sumin like dis.

DIGItonium · 09-02-2010, 06:52 PM

Quote:

Originally Posted by Joka4411

WoW where do you get the guts to tryout sumin like dis.

It takes lots of thinking and planning (i.e., need down time). I did the same work with the 350Z, and it was easier than the 370Z. However, putting the needles back on with the 370Z is so much easier because I didn't have to drive the car while putting the needle back on. The only thing left is the triple meter, but I've decided to replace those with aftermarket gauges.

05-29-2010, 09:43 PM	#33 (permalink)
theDreamer A True Z Fanatic Join Date: Feb 2009 Location: Texas Posts: 30,879 Drives: 370z Rep Power: 4210	Digi, do you plan on doing the triple gauge cluster over the center console? I know it will require removing I think the dash as some have stated, but you would be the first at doing a full DIY(ish) on the forum. __________________ theDreamer's Z // Fast Intentions // Uprev // GTM // HKS // TEIN theDreamer's Silvia // URAS // GREDDY Houston Zs // Facebook // Twitter // Instagram

05-30-2010, 04:22 PM	#35 (permalink)
XwChriswX WFLYIDNNE Join Date: Jul 2009 Location: In The Fastlane Posts: 50,648 Drives: 02 GDB WRX Rep Power: 452	Digi, you really need to sloooow down lol I haven't even gotten the Driver's side door done, and your throwing all these new ideas at me! LoL __________________ Bonnie - Stage 2, Audio build coming this fall! R.I.P. Abby 3/29/10 - 3/30/14

05-31-2010, 03:04 AM	#36 (permalink)
DIGItonium A True Z Fanatic Join Date: Jan 2009 Location: Kansas Posts: 3,800 Drives: 09 Z34-TT 6MT Rep Power: 42	Bump... updated DIY: Interior LED Color Change __________________

09-01-2010, 11:12 PM	#44 (permalink)
Joka4411 Base Member Join Date: May 2010 Location: Baltimore Md Posts: 131 Drives: 40th anniver 370Z Rep Power: 15	WoW where do you get the guts to tryout sumin like dis. __________________ 2010 40th Anniversary Z Owner

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Want to change the interior	Gables	Exterior & Interior	10	05-17-2012 05:19 PM
pod lighting color change?	g35300mm	Nissan 370Z General Discussions	2	02-10-2010 02:28 PM
what interior color??	Arcangel	Nissan 370Z General Discussions	15	03-08-2009 11:11 PM
powdercoating just to change color?	mattkim85	Nissan 370Z General Discussions	2	03-02-2009 04:08 PM

05-31-2010, 03:12 AM	#37 (permalink)
Boost_lee A True Z Fanatic Join Date: Feb 2009 Location: SATX Posts: 2,813 Drives: 09 370Z TT 6MT Rep Power: 29	Digitonium - you do outstanding work, love this DIY

06-10-2010, 12:31 AM	#39 (permalink)
gromano Enthusiast Member Join Date: Jul 2009 Location: Brisbane (South) Posts: 308 Drives: 09 Nissan 370Z- Blue Rep Power: 16	Hey Digitonium, Nice mods!! I wanna do the mirror/visor light conversion to LED!!!! I got no idea how to string the LED's together like you did. And Im not sure on the sizing of them either... Do you know if any of the bulbs shown on this site would fit? http://www.led-online.com.au/index.p...mart&Itemid=37 Keeping in mind Im in Australia! Figured you would help with sizing and Volts etc Want some for the map lights/ambient lights too but dont know what to use. Hate having red lights in my sexy blue car! hahaha Thanks for your help

06-11-2010, 01:18 PM	#40 (permalink)
farmosh203 Base Member Join Date: Nov 2009 Location: Arizona Posts: 24 Drives: 09 Nissan 370Z sport Rep Power: 16	That's really impressive you had the balls to take everything apart like that. Soldering anything above an 0402 size is no problem but I can't imagine taking my car apart and putting it back together like that. I'm still trying to think of ideas on what I could do to my car using a microcontroller.

07-21-2010, 02:28 PM	#43 (permalink)
CBRich A True Z Fanatic Join Date: Apr 2009 Location: SC Posts: 2,464 Drives: 370Z Rep Power: 544	SUBscribing. I need to get on this.