DIY Yaw Sensor rocker switch

cossie1600 · 01-30-2019, 03:45 AM

Quote:

Originally Posted by cossie1600

So that green wire is a pain in the *** to get to. Would it seem smart to insert two posi tap to the wire at both ends, then extend the wire to an on off switch. After that, just cut the wire in between the two posi tap?

It’s alive

Just zip ties the rest of the wire to stick the green one out, insert the posi tap and go to town with it. Once everything is secure, cut the green wire and you are good to go

Tractionless · 01-31-2019, 02:12 PM

I notice when using the switch it will turn both slip and traction control off. Is it ok to engage in this manner or should traction control be turned off first than the yaw switch?

Girald · 02-19-2020, 12:07 AM

Quote:

Originally Posted by SG4247

The other option is the throttle hijack feature from Ecutek.

I just got mine working, and the software changes to the ECU will now allow me to burn rubber with the brake on as far and as long as I want.

My yaw sensor has been disabled for years. That had zero impact on burnout capability.

What actually happens in your case, is that the throttles will be closed, if the ECU sees the brake switch on and the gas pedal voltage high. This effectively prevents the driver from pressing the brake and gas pedal at the same time. The yaw sensor is not an input in this case.

interesting...did yuou have to splice any ecu wires or is it straight to ecuteck via exisiting? im about about to finish off my flex tuning in the spring and might ask to have this dropped in on my phone app (bluetooth dongle).. do you know if that kills ice mode as well, or is that an abs hard disable?

Girald · 02-23-2020, 08:43 PM

BTW..

as of time of this post, i found the switches on amazon... they cost me a buck & change each and fit perfectly.

https://www.amazon.com/gp/product/B0...?ie=UTF8&psc=1

i already hooked up my pump speed controller override, the vdc bosch box is next and have duct fan control on #3 in the works.

only thing of concern.. watch your wiring, your e brake can bump and possibly snag the wires, so keep that in mind...

and for petes sake, use spade connectors, heat shrink and solder. its a permanent install so treat it as such.

CamZ · 03-24-2020, 02:07 PM

what do you mean by this?

NissanTracker · 03-30-2021, 10:49 AM

I have some OE style Push switches that makes the Yaw mod a lot cleaner. I have a bunch of extras.

https://drive.google.com/file/d/1XDH...ew?usp=sharing

https://drive.google.com/file/d/1XYo...ew?usp=sharing

fairladyATX · 09-04-2021, 01:18 PM

Quote:

Originally Posted by NissanTracker

I have some OE style Push switches that makes the Yaw mod a lot cleaner. I have a bunch of extras.

https://drive.google.com/file/d/1XDH...ew?usp=sharing

https://drive.google.com/file/d/1XYo...ew?usp=sharing

I just got mine in the mail you sent me.

Since there are 4 wires on the back, do you only use 2 of them, one on each pole? Or do you need to crimp them into 2 sets, then connect to the YAW wire?

Just am not sure how to go about this since this switch is illuminated.

Maldat · 09-10-2021, 03:42 AM

Quote:

Originally Posted by jchammond

Pic of TC turned off & 2nd picis with Yaw sensor(green wire)open.

I called it my “Drift Switch” & didn’t bother with TC switch after adding yaw disconnect switch.
Never played with ABS to see how they performed while yaw was disabled.
Good to know they work

Sent from my iPhone using Tapatalk

Hi . Off topic. but that warning light ,, , that flashs hard out seams like every time I change down a few gears and pull out to pass on the open road ..

is this normal ?.
car has brand new tyres

jchammond · 09-10-2021, 04:03 AM

Quote:

Originally Posted by Maldat

Hi . Off topic. but that warning light ,, , that flashs hard out seams like every time I change down a few gears and pull out to pass on the open road ..

is this normal ?.
car has brand new tyres

What sizes are your tires?
As it could be a couple different things

Also does the throttle cut or stumble any during acceleration?

Spooler · 09-17-2021, 04:12 PM

Quote:

Originally Posted by Maldat

Hi . Off topic. but that warning light ,, , that flashs hard out seams like every time I change down a few gears and pull out to pass on the open road ..

is this normal ?.
car has brand new tyres

That means your rear tires are spinning if everything is working properly and it is in traction control mode. Turn the traction control off and then try it. You will see real quick if it is spinning so be prepared to take proper measures with your right foot or you may loose it.

k67p67 · 09-18-2021, 10:00 PM

Quote:

Originally Posted by fairladyATX

Since there are 4 wires on the back, do you only use 2 of them, one on each pole? Or do you need to crimp them into 2 sets, then connect to the YAW wire?

Just am not sure how to go about this since this switch is illuminated.

Black = ground
Red = 12V+ parking lights
Yellow = 12V+/Switched Ignition/Accessory depending on what your plans are for the switch. You can find a switched ignition source if you are using it to disable the yaw sensor.
Blue = terminal 85 or 86 of your SPDT relay

You can combine the yellow and red wires but the switch icons will be illuminated even when it's not dark outside.

$ully · 11-02-2022, 03:03 PM

I just pulled the whole sensor. Aside from the dash light showing the "slip" warning always being lit, the car is rolling along like it never even heard about a yaw sensor. I don't know how to disable the "slip" warning light on the dash though. Anyone know how to do that?
I guess the bulb will eventually wear out at some point...lol

redondoaveb · 11-02-2022, 04:55 PM

Quote:

Originally Posted by $ully

I just pulled the whole sensor. Aside from the dash light showing the "slip" warning always being lit, the car is rolling along like it never even heard about a yaw sensor. I don't know how to disable the "slip" warning light on the dash though. Anyone know how to do that?
I guess the bulb will eventually wear out at some point...lol

It's a tiny led. You'll probably die of old age before it burns out

GoldenDragon · 08-28-2023, 10:08 PM

i have an 09 370z m/t.
i bought another hazard light switch and wired the yaw switch mod to that switch and put it into the blank switch opposite of it (passenger side of shifter). This only works on the m/t, automatic's actually have a functional switch there.
Spray painted the top of the swich silver to match the silver trim. At a glance if the button is flush with the trim the yaw is disconected and the dummy warning light is on. When the button is depressed, its back to stock with no dummy lights. It's always in off mode unless i need to bring it to a shop (drove them nuts, cause they couldnt clear it).
I also have the heated seats, so 2 out of the three slots where filled on the center console. I used the middle slot and put a dim green illuminated switch, that controls my drl's in the headlight housing. It's the one wire mod for drl's on earlier model 370z's on this site. Just a different way of using the limited space while keeping it stock looking.

01-31-2019, 02:12 PM	#62 (permalink)
Tractionless A True Z Fanatic Join Date: Jan 2016 Location: Atlantic SE Posts: 1,326 Drives: '10 K23 ST 7AT Rep Power: 30525	I notice when using the switch it will turn both slip and traction control off. Is it ok to engage in this manner or should traction control be turned off first than the yaw switch? __________________ Toys Not Tots

02-23-2020, 08:43 PM	#64 (permalink)
Girald Base Member Join Date: Jun 2017 Location: Denver Posts: 135 Drives: 15' 370z SpTech 6MT Rep Power: 3363	BTW.. as of time of this post, i found the switches on amazon... they cost me a buck & change each and fit perfectly. https://www.amazon.com/gp/product/B0...?ie=UTF8&psc=1 i already hooked up my pump speed controller override, the vdc bosch box is next and have duct fan control on #3 in the works. only thing of concern.. watch your wiring, your e brake can bump and possibly snag the wires, so keep that in mind... and for petes sake, use spade connectors, heat shrink and solder. its a permanent install so treat it as such. __________________ AAM tt'ed // Soon: Moving back to the East Coast

03-30-2021, 10:49 AM	#66 (permalink)
NissanTracker Track Member Join Date: Jun 2016 Location: Massachusetts Posts: 724 Drives: 07' Nismo, 14' Nismo Rep Power: 29262	I have some OE style Push switches that makes the Yaw mod a lot cleaner. I have a bunch of extras. https://drive.google.com/file/d/1XDH...ew?usp=sharing https://drive.google.com/file/d/1XYo...ew?usp=sharing Rusty, Hotrodz and Csharpminor like this.

08-28-2023, 10:08 PM	#74 (permalink)
GoldenDragon Base Member Join Date: Sep 2017 Location: Brentwood Posts: 2 Drives: 09 370z silver 6m Rep Power: 8	i have an 09 370z m/t. i bought another hazard light switch and wired the yaw switch mod to that switch and put it into the blank switch opposite of it (passenger side of shifter). This only works on the m/t, automatic's actually have a functional switch there. Spray painted the top of the swich silver to match the silver trim. At a glance if the button is flush with the trim the yaw is disconected and the dummy warning light is on. When the button is depressed, its back to stock with no dummy lights. It's always in off mode unless i need to bring it to a shop (drove them nuts, cause they couldnt clear it). I also have the heated seats, so 2 out of the three slots where filled on the center console. I used the middle slot and put a dim green illuminated switch, that controls my drl's in the headlight housing. It's the one wire mod for drl's on earlier model 370z's on this site. Just a different way of using the limited space while keeping it stock looking. KapitalZ likes this.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Yaw sensor switch	dimitarm	Exterior & Interior	33	08-09-2017 11:13 PM
YAW Sensor Rocker Switch	dP3NGU1N	DIY Section (Do-It-Yourself)	23	11-10-2013 06:57 PM
Viper Security System/Tilt sensor/Proximity sensor	kfull	Nissan 370Z General Discussions	4	04-27-2012 01:10 AM
Installed the Rocker Stripe (pic)	kent370	Member's 370Z Gallery	9	02-15-2012 04:30 PM
Rocker panel chips?	JGreenwood07	Exterior & Interior	2	07-14-2010 11:58 AM

03-24-2020, 02:07 PM	#65 (permalink)
CamZ Base Member Join Date: Jul 2019 Location: CA Posts: 1 Drives: 13 Nissan 370Z Rep Power: 6	what do you mean by this?

11-02-2022, 03:03 PM	#72 (permalink)
$ully Base Member Join Date: Apr 2013 Location: Inwood, Ontario, Canada Age: 62 Posts: 16 Drives: 13 370Z Roadster 6mt Rep Power: 3367	I just pulled the whole sensor. Aside from the dash light showing the "slip" warning always being lit, the car is rolling along like it never even heard about a yaw sensor. I don't know how to disable the "slip" warning light on the dash though. Anyone know how to do that? I guess the bulb will eventually wear out at some point...lol