DIY Yaw Sensor rocker switch

newls196

gonna do this over the weekend... anything different on a 2012 model or all the same? Thanks

__________________
2012 370z
6MT "Sport Package" Z1 CSC, Z1 Test Pipes, ARK Catback, Injen CAI, SpeedBooster, Custom PCV Canister setup, Z1 dyno tune coming soon

SouthArk370Z

You may want to download the FSM for your year and verify wire colors.

__________________
Steering Lock Links - Search The370Z Bookmarklet - FSM @ NICOclub
Mankind has progressed past the need for war but we haven't evolved that far. - NachoMahma

makugx

Hey!
I couldn't find 20 gauge wire anywhere!
(home depot, lowes, advanced auto parts)

Can I use 18 gauge?

Thanks!

20 gauge wire
soldering wire
soldering gun
and a couple of heat shrink tubes
x-acto knife or wire stripper
One SPST switch of your choice. I picked one that fit into the center console area where the control for the convertible top would go. The mounting hole dimension for this slot is 35mm x 20mm but the switch I purchased was in imperial (1.45in x 0.83in) and it worked just fine.

SouthArk370Z

Yes. 20 ga or lower will work. Wire gauges are "backwards" - the smaller the gauge number, the larger the wire is.

Since it's signal-level, you could probably get away with 22 ga wire ... but I wouldn't recommend it.

__________________
Steering Lock Links - Search The370Z Bookmarklet - FSM @ NICOclub
Mankind has progressed past the need for war but we haven't evolved that far. - NachoMahma

beemerkid

I just did this, and it lights up the dash and resets when the car is shut off on my 16. I'll have to report back on how I like all nannies off when I autox next weekend. I used a mini toggle switch and kept it under the cupholder, partially for the cleanest look, and partially so I don't get a hair up my *** on a wet road and decide to go a little crazy and end up missing a tree because of it. I know I can crash anyways but turning off all the safeties to intentionally screw around is something I want hidden, I don't trust myself that much haha. Besides the cup holder is very easy to remove.

SG4247

Just put mine under the cup holder too.

My on-off switch came prewired with two black wires about 4" long - bought it from O'Reillys -saving me some install time.

Works perfectly on my 2010!

Good call beemerkid!

B&W_Evader

Finally did mine last night after work. Been loosening up the cup holder for the last week. Yanked on it a little at a time and it finally popped. I have not had a road open up enough yet to really test it out. It is so nice not to have to hit the VDC Off button every time I get in the car. And... the switch pops in perfect and looks OEM.

__________________
|RIP|6spd-sport|OSG-LSD|XP8|RBF600|Eibach Sways|RE-71R|FI-34Row|Gen3-CAI|Yaw P.S.|

Kamillio

Has anyone found a switch that pops into the OEM mounting location?


Sent from my iPhone using Tapatalk

__________________
370z

B&W_Evader

WiringProducts - The Place to Buy Electrical Supplies
Full Size Rocker Switches - 1/4'' Tabs - ON-OFF SPST - Wiring Products

Attached Images

	Yaw_Switch.jpg (69.3 KB, 90 views)
	Yaw_switch2b.jpg (196.0 KB, 101 views)

__________________
|RIP|6spd-sport|OSG-LSD|XP8|RBF600|Eibach Sways|RE-71R|FI-34Row|Gen3-CAI|Yaw P.S.|

SG4247

Ive gotten to leaving VDC and yaw off all the time now, i just ignore the lights on the dash.

Dont ever drive in the rain or snow, so cant think of any reason or anytime I have needed to switch it back on!

OhioYJ

Well finally did this. My OCD wouldn't allow me to have just one switch and two blank panels, so I ordered three switches. Also my OCD needs to have the switches in the same direction, so the switch for the yaw sensor is backwards, as normally most accessories would not be on all the time:



I always de-insulate the terminals so I can solder after crimping. Just a habit from my Jeep I guess, so I re-insulate them with heat-shrink afterwards:



At least there is lots of areas underneath to keep the wires out of the way:



I think with three switches it looks OEM:

B&W_Evader

Nice work Ohio! We received some unseasonable rain in CA last Friday and I was able to put this mod to the test. I found a couple of spots to pitch it sideways and keep my foot in it. I need a bunch of practice before I feel completely comfortable doing this. Throttle modulation is pretty tough because of the short wheelbase, it really wants to hang out if you give it too much gas, but no whip-back caused by the computer hitting the brakes. Finally, the car isn't trying to kill me any more. Note that this is combined with an aftermarket LSD.

__________________
|RIP|6spd-sport|OSG-LSD|XP8|RBF600|Eibach Sways|RE-71R|FI-34Row|Gen3-CAI|Yaw P.S.|

Ghost116

Can anyone confirm it's the green wire on 2014+....and for any electrically inclined would a reverse polarity switch be ok to use? I can source them locally and they look pretty oem. I just don't know if it would hurt anything


Sent from my iPhone using Tapatalk

SouthArk370Z

Not sure if wire color is still the same.

A DPDT switch (AKA reverse polarity switch) will work just fine but you'll only use one pole of the switch. A SPST switch will also do the job and should be cheaper.

__________________
Steering Lock Links - Search The370Z Bookmarklet - FSM @ NICOclub
Mankind has progressed past the need for war but we haven't evolved that far. - NachoMahma

Ghost116

Thanks for the reply I'm going to check for the cheaper regular two pole. But all they seem to show online is the reverse polarity. I would assume they would have both but figured I would check just incase


Sent from my iPhone using Tapatalk