Nissan 370Z Forum  

DIY: DRL Wiring For Pre-'13 Z's

First off, I want to give credit to TheW3r3w0lf and Fountainhead for information they provided in this thread: Daytime Running Lights + Switchback LEDs Their info was very instrumental with

Go Back   Nissan 370Z Forum > Nissan 370Z Tech Area > DIY Section (Do-It-Yourself)


Like Tree9Likes

Reply
 
LinkBack Thread Tools Display Modes
Old 07-31-2013, 09:48 PM   #1 (permalink)
Base Member
 
Dave N's Avatar
 
Join Date: Oct 2011
Location: Orange County, CA
Posts: 123
Drives: '12 PW 6M & 90 Z32TT
Rep Power: 14
Dave N is on a distinguished road
Default DIY: DRL Wiring For Pre-'13 Z's

First off, I want to give credit to TheW3r3w0lf and Fountainhead for information they provided in this thread: Daytime Running Lights + Switchback LEDs Their info was very instrumental with the development of these instructions.

This DIY will allow you to wire up a set of switchback LEDs for use as DTRL on pre-2013 Z's. The DTRLs will be active when the ignition switch is in the "ON" position but they will deactivate when the running lights or headlights are turned on (whether the headlights are set to auto or manually turned on). This set up can utilize the existing dual filament bulb or switchback LEDs (wiring differences will be detailed in the body of the DIY).

OBLIGATORY DISCLAIMER:You are doing this modification at your own risk and, as such, will take on any responsibilities for this installation successful or otherwise. Please read all the way though this DIY at least once to be sure you fully understand the steps before starting this project

The modification does not require significant electrical skills (no soldering required), however basic mechanical skills are needed to do this DIY.

Items required:

Tools:
Wire stripper/crimper
Small flat blade screwdriver
10mm socket/wrench
Heat gun (required if using heat shrink tubing)
Jack and jack stands
21mm socket for tire removal (preferably 1/2" drive, or use the tire wrench in the spare tire tool kit)
Materials:
Automotive grade relay (typically 12V/40 Amp rating) - must be "Normally Closed" (you can find these at electronics supply stores and some automotive supply stores - they may be combo Normally Open/Normally Closed relays).
Here is an example available through Autozone
Here is an example available through Radio Shack *Since specifications change, and photos of the products used on websites aren't always accurate, be sure to verify with the seller that the relay will support a "normally closed" circuit before you purchase it.
5 Pin socket w/leads for the relay - must match the pin pattern on the relay. Here is an example available through Radio Shack
16 or 18 gauge wire in colors of your choice (2 colors were used in my installation: blue for connecting the power leads to the lights/relay and black for ground connections
Ring connectors Here is an example available through Autozone
Butt splices
Inline splices
Heat shrink tubing (or electrical tape).
Step one:
Disconnect the battery positive (+) terminal
Next, locate the relay box on the driver's side - just forward of the strut tower:


Depress the lock tab that secures it to the bracket and slide it upwards until it is out of the bracket.


Turn the relay box upside down and remove the bottom cover by releasing the snap-tabs (yellow dots).



Remove the cover and locate the DTRL RELAY using the diagram on the cover.


The DTRL relay is the blue relay mounted to the white connector base (note: this photo shows the new relay (black) already installed).


Using a small flat blade screwdriver, depress the lock tab (left of red dot) to remove the relay and its connector from the black enclosure (it will slide up towards you).


With the DTRL relay free from its mount, turn it over and locate the light brown (see blue dot in photo below).


Referring to the attached wiring schematic (courtesy of Fountainhead)

Look at the relay you purchased and note the connection diagram on the top of the relay (note: look for this info when buying the relay - it should either be printed/embossed on the relay or printed on the packaging).


For the relay I used, I noted the pin numbers on Fountainhead's wiring diagram as shown below:

Please note that the relay you have may show different pin numbers. The important thing to do is to associate the pin numbers (if different) with the same positions on the relay diagram in the picture.

When making the following connections, you can clean up the installation by cutting the wires to be just long enough to reach the adjacent connectors. This will make it much easier to tuck these wires into place when reinstalling the bottom cover for the relay box.

Splice the wire for relay pin 85 (the relay connector should have numbers embossed in the housing to identify which wire connects to the relay) to the light brown wire on the DTRL relay by using an in-line splice (sample image of in-line splice shown below).


After the splice is made, you can replace the DTRL relay into the relay housing base and remove the brown relay connector (green dot):


Remove the green wire (I chose to remove the terminal from the connector, but you can simply cut the wire as close to the base as possible if preferred).


Cut off the terminal from the wire and strip approximately 1/4" of insulation from the end. If using heat shrink tubing to seal the splice, cut approximately 1-1/4" ~ 1-1/2" of heat shrink tubing and slide it onto one of the wires BEFORE making the splice. Using a butt-splice, connect the green wire to the wire for pin 30* of the relay. After crimping the butt-splice, slide the heat shrink tubing over the splice and use a heat gun to shrink the tubing. Be careful not to use too high of a heat setting otherwise you may melt the tubing or wire insulation. If electrical tape is being used, it can be applied after crimping the butt-splice.


Crimp a ring connector to the wire for pin 86. For my installation, I combined this wire with the ground connection for the driver side load resistor:


...and connected them to the chassis ground adjacent to the relay box:


Do not install the bottom cover yet. This will be done at the end after you recheck all the connections and test the system.

Step two:
Carefully jack up the front end and place it on jack stands
Remove both front tires
Remove the plastic clips securing fender liners on the driver and passenger sides.

Locate the parking light socket and twist the socket to the left to remove from the headlight housing (yellow dot; passenger side shown in the photo below - left side is similar):


Take the black wire and pull it out of the blue sleeve. Cut off the black shrink tube that is sealing the end of the wire and strip approximately 1/4" of insulation off the end of this wire. Take a butt-splice and a piece of heat-shrink tubing, slide the heat-shrink tubing onto the black wire, and then crimp the butt-splice to it. Next, run a length of wire (avoiding sharp metal edges or moving parts) from the relay box to the headlight area and crimp this wire into the other end of the butt-splice. Slide the heat-shrink tubing in place and shrink it (or wrap with electrical tape). At the relay box, connect this wire to pin 87a of the relay connector using a butt-splice and heat-shrink tubing. When doing this for the passenger side, you will need to run the wire over to the relay box on the driver side fender well and connect it to the wire for pin 87a using a butt-splice. Be careful when routing this wire to avoid contact with moving parts or sharp edges. For my installation, I routed the wire along the front of the radiator area by removing the black plastic cover on the front core support.


Here is a picture of the in-line splice connecting the passenger side wire to the relay connector.


**
FOR SWITCHBACK LEDs, PERFORM THE NEXT STEP TO INSTALL THE LOAD RESISTOR. IF USING THE OEM DUAL-FILAMENT BULBS, SKIP THE LOAD RESISTOR INSTALLATION.
**

Two load resistors should be supplied with the switchback LEDs. One will be needed for each LED installation.

Locate the grey connector attached to the headlight housing and find the wire that is green with a black stripe on it. Attach an in-line splice to connect one lead on the load resistor with the green/black stripe wire (the blue sleeve may need to be trimmed back a little).


On the other resistor lead, attach a length of wire suitable to reach a grounding point on the car. Use a butt-splice and heat-shrink tubing (or electrical tape) for this connection. Install a ring connector on the opposite end of the wire.


Attach the ring connector to chassis ground and secure the resistor to prevent it from rattling or bouncing around (green dot; passenger side example shown in photo below):


Repeat the above steps for the opposite side.

Step Three:
Recheck all electrical connections to be sure they are securely crimped and per the relay wiring diagram. Make any corrections if needed. Once everything is checked, reconnect the positive terminal on the battery. Turn the ignition switch to "ON" and check that both LEDs illuminate in white:


Next, check each turn signal operates correctly and illuminates in amber (this photo is a little washed out from the overhead lights):


If the turn signal flashes quickly (hyperflash), recheck the connections to the load resistor to be sure there are no bad crimps or bad ground connections. Note: if checking the turn signals using the hazard switch, you may not find the hyperflash problem - you must check the turn signals individually.

Finally, turn the parking or headlights on and confirm the DRLs turn off.

Turn the ignition switch off and pat yourself on the back for a job well done.

Now that everything checks out OK, make sure all wire installations are secured and routed away from anything that could damage them.

Reinstall the following items:
Fender liners
Wheels
Bottom and top covers for the relay box
Relay box on the inner fender
Anything else that was removed for the installation
Don't hesitate to PM me if anything isn't clear from these instructions.

This completes the DIY. Enjoy!

**No fuses were harmed during the creation of this DIY** ;-)

Last edited by Dave N; 09-23-2013 at 07:39 PM.
Dave N is offline   Reply With Quote
Old 08-01-2013, 08:15 AM   #2 (permalink)
A True Z Fanatic
 
GaleForce's Avatar
 
Join Date: Aug 2011
Location: Ontario, Canada
Posts: 21,749
Drives: Varis Arising II
Rep Power: 51865
GaleForce has a reputation beyond reputeGaleForce has a reputation beyond reputeGaleForce has a reputation beyond reputeGaleForce has a reputation beyond reputeGaleForce has a reputation beyond reputeGaleForce has a reputation beyond reputeGaleForce has a reputation beyond reputeGaleForce has a reputation beyond reputeGaleForce has a reputation beyond reputeGaleForce has a reputation beyond reputeGaleForce has a reputation beyond repute
Default

Nice DIY. Good job.
__________________
GaleForce is offline   Reply With Quote
Old 08-04-2013, 04:27 PM   #3 (permalink)
A True Z Fanatic
 
Nut_N_Much's Avatar
 
Join Date: Dec 2011
Location: Pensacola Florida
Posts: 1,696
Drives: Awesome Car
Rep Power: 26
Nut_N_Much has a reputation beyond reputeNut_N_Much has a reputation beyond reputeNut_N_Much has a reputation beyond reputeNut_N_Much has a reputation beyond reputeNut_N_Much has a reputation beyond reputeNut_N_Much has a reputation beyond reputeNut_N_Much has a reputation beyond reputeNut_N_Much has a reputation beyond reputeNut_N_Much has a reputation beyond reputeNut_N_Much has a reputation beyond reputeNut_N_Much has a reputation beyond repute
Default

Wow, I like it.. Nice DIY, I read it a few times but didn't see a part number or link to were you guy's are getting the Bulbs. Can you post that, I would like to do this mod when I re-due my lights..

Thanks for the write up +1
diddofbean likes this.
Nut_N_Much is offline   Reply With Quote
Old 08-05-2013, 04:08 PM   #4 (permalink)
Base Member
 
Dave N's Avatar
 
Join Date: Oct 2011
Location: Orange County, CA
Posts: 123
Drives: '12 PW 6M & 90 Z32TT
Rep Power: 14
Dave N is on a distinguished road
Default

Quote:
Originally Posted by Nut_N_Much View Post
Wow, I like it.. Nice DIY, I read it a few times but didn't see a part number or link to were you guy's are getting the Bulbs. Can you post that, I would like to do this mod when I re-due my lights..

Thanks for the write up +1
There are one or two references in the DRL post I linked at the beginning of the DIY. To avoid a lengthy search and click exercise, here is the info I gleaned from that post:

One person posted this link: 7441 Dual Color No Error High Power Projector LED Turn Lights Resistors 7W 68C | eBay, however I had two failures out of four bulbs that came from Kaizenmotor on eBay (and so far I have not been able to locate their contact info for a refund). Here is my post describing the problem with the Kaizenmotor LEDs. I'd stay away from these for now.

Here is the link to TheW3r3W0lf's post on sourcing LEDS: Daytime Running Lights + Switchback LED’s
I have not researched these bulbs yet so I can't say if these are any better than the first ones I tried.

Good luck, I hope this helps.

Dave

Last edited by Dave N; 08-05-2013 at 07:44 PM.
Dave N is offline   Reply With Quote
Old 08-08-2013, 09:59 PM   #5 (permalink)
Enthusiast Member
 
HArturo319's Avatar
 
Join Date: Jun 2012
Location: Houston, TX
Posts: 323
Drives: 2013 PW NISMO
Rep Power: 13
HArturo319 is on a distinguished road
Default

excellent write up... How long did the whole process take?
__________________


Me And Zoloft Get Along Just Fine
HArturo319 is offline   Reply With Quote
Old 08-09-2013, 03:01 PM   #6 (permalink)
A True Z Fanatic
 
Nut_N_Much's Avatar
 
Join Date: Dec 2011
Location: Pensacola Florida
Posts: 1,696
Drives: Awesome Car
Rep Power: 26
Nut_N_Much has a reputation beyond reputeNut_N_Much has a reputation beyond reputeNut_N_Much has a reputation beyond reputeNut_N_Much has a reputation beyond reputeNut_N_Much has a reputation beyond reputeNut_N_Much has a reputation beyond reputeNut_N_Much has a reputation beyond reputeNut_N_Much has a reputation beyond reputeNut_N_Much has a reputation beyond reputeNut_N_Much has a reputation beyond reputeNut_N_Much has a reputation beyond repute
Default

Quote:
Originally Posted by Dave N View Post
There are one or two references in the DRL post I linked at the beginning of the DIY. To avoid a lengthy search and click exercise, here is the info I gleaned from that post:

One person posted this link: 7441 Dual Color No Error High Power Projector LED Turn Lights Resistors 7W 68C | eBay, however I had two failures out of four bulbs that came from Kaizenmotor on eBay (and so far I have not been able to locate their contact info for a refund). Here is my post describing the problem with the Kaizenmotor LEDs. I'd stay away from these for now.

Here is the link to TheW3r3W0lf's post on sourcing LEDS: Daytime Running Lights + Switchback LED’s
I have not researched these bulbs yet so I can't say if these are any better than the first ones I tried.

Good luck, I hope this helps.

Dave
Nice, thanks for the links. His look like good quality LEDs.

Quote:
Originally Posted by HArturo319 View Post
excellent write up... How long did the whole process take?
I think it said about 45 min's for the hole job..
Nut_N_Much is offline   Reply With Quote
Old 08-12-2013, 02:42 PM   #7 (permalink)
Base Member
 
Dave N's Avatar
 
Join Date: Oct 2011
Location: Orange County, CA
Posts: 123
Drives: '12 PW 6M & 90 Z32TT
Rep Power: 14
Dave N is on a distinguished road
Default

Quote:
Originally Posted by HArturo319 View Post
excellent write up... How long did the whole process take?
It will depend on the skill of the person doing the work. I'd allow for 2 ~ 3 hours in case there are any issues encountered during the install. This isn't something to rush through and end up accidentally blowing fuses.
chubbs and Nut_N_Much like this.
Dave N is offline   Reply With Quote
Old 08-28-2013, 05:40 AM   #8 (permalink)
Base Member
 
Join Date: Apr 2011
Location: VA
Posts: 58
Drives: '10 Z34 Blue 7AT NAV
Rep Power: 14
sselemit is on a distinguished road
Default

My 10' does not have the DTRL and Heater Seat relays. Do you know any other place to tap in for power?

Thanks
sselemit is offline   Reply With Quote
Old 09-11-2013, 05:11 PM   #9 (permalink)
Base Member
 
Dave N's Avatar
 
Join Date: Oct 2011
Location: Orange County, CA
Posts: 123
Drives: '12 PW 6M & 90 Z32TT
Rep Power: 14
Dave N is on a distinguished road
Default

You're saying that there are no connectors at all, or just the relays are not there?

If the plug sockets are there, then you can still tap them for the needed power signals.

However, if neither connector is present, then you could pick up any power source that is live when the ignition is turned to the "ON" position. The potential downside is that without the DTRL line to cut power when the headlights come on, the running lights will stay on all the time.

I hope this helps.

Dave
Dave N is offline   Reply With Quote
Old 09-21-2013, 05:10 PM   #10 (permalink)
A True Z Fanatic
 
chubbs's Avatar
 
Join Date: Jan 2009
Location: Zeeland
Posts: 1,046
Drives: 2016 370z Auto-Grey
Rep Power: 7586
chubbs has a reputation beyond reputechubbs has a reputation beyond reputechubbs has a reputation beyond reputechubbs has a reputation beyond reputechubbs has a reputation beyond reputechubbs has a reputation beyond reputechubbs has a reputation beyond reputechubbs has a reputation beyond reputechubbs has a reputation beyond reputechubbs has a reputation beyond reputechubbs has a reputation beyond repute
Default

Dave - Thank you very much for this excellent guide. I've been searching for quite a long time for something like this. I'm not brave enough to bake my headlights in the oven and aftermarket DRL strips just won't look right. However this idea that Werewolf, Fountainhead and you have developed might just be the solution I've been looking for.

My next job is to see if I can source the parts here in the UK - and summon up the courage to do a bit more electrical work on my car. Electricity is definitely not my strong point, but your amazingly clear guide may just tempt me to have a go.
Dave N likes this.
__________________
.

'03 Grey >>> '06 Black >>>'10 Silver >>> '16 Grey ^
chubbs is offline   Reply With Quote
Old 09-23-2013, 07:53 PM   #11 (permalink)
Base Member
 
Dave N's Avatar
 
Join Date: Oct 2011
Location: Orange County, CA
Posts: 123
Drives: '12 PW 6M & 90 Z32TT
Rep Power: 14
Dave N is on a distinguished road
Default

Quote:
Originally Posted by chubbs View Post
Dave - Thank you very much for this excellent guide. I've been searching for quite a long time for something like this. I'm not brave enough to bake my headlights in the oven and aftermarket DRL strips just won't look right. However this idea that Werewolf, Fountainhead and you have developed might just be the solution I've been looking for.

My next job is to see if I can source the parts here in the UK - and summon up the courage to do a bit more electrical work on my car. Electricity is definitely not my strong point, but your amazingly clear guide may just tempt me to have a go.
Thanks for the feedback. I'm quite confident that you can find the equivalent parts in the UK. If you are uncertain about a particular item, don't hesitate to contact me and I'll do my best to confirm if the part in question can be substituted.

Better yet, if you and your local Z/Zed friends want to chip in and fly me out, I'll bring all the necessary parts with me and make a weekend of doing the installs your cars.

Dave
Dave N is offline   Reply With Quote
Old 02-03-2014, 09:21 PM   #12 (permalink)
FLP
Base Member
 
Join Date: Jan 2013
Location: Orlando
Posts: 2
Drives: 2006 350Z Roadster
Rep Power: 12
FLP is on a distinguished road
Default

Hi everyone!
I'm relatively new to this forum, but have had several Zs. I'm picking up my 370Z roadster in one week and want to do this with the headlights.

Frankly, I lack the technical expertise and knowledge to do this myself although I still need to buy the parts. I'm only confused on the bulbs.

Can someone please tell me in layman's terms a good description of the bulb needed for this so I can search.

Any specific brands?

Or any specific online auto supply stores?

Thanks in advance for dumbing it down for me. I really do appreciate and love the DIY!
FLP is offline   Reply With Quote
Old 03-02-2014, 05:31 PM   #13 (permalink)
Enthusiast Member
 
km1346's Avatar
 
Join Date: Aug 2013
Location: Dallas, TX
Posts: 370
Drives: 40th Anniversary
Rep Power: 12
km1346 is on a distinguished road
Default

Great writeup!
Unfortunately my electric skills are horrible and even though I could attempt this I would be to scared to mess something up and blow a fuze..

Anyone in the Dallas, Ft. Worth area capable of doing this?
PM me if you can.
You will be paid for your help.
km1346 is offline   Reply With Quote
Old 03-05-2014, 06:06 PM   #14 (permalink)
Base Member
 
Dave N's Avatar
 
Join Date: Oct 2011
Location: Orange County, CA
Posts: 123
Drives: '12 PW 6M & 90 Z32TT
Rep Power: 14
Dave N is on a distinguished road
Default

Quote:
Originally Posted by km1346 View Post
Great writeup!
Unfortunately my electric skills are horrible and even though I could attempt this I would be to scared to mess something up and blow a fuze..

Anyone in the Dallas, Ft. Worth area capable of doing this?
PM me if you can.
You will be paid for your help.
Come to ZCON. I'm about an hour from the convention site.
Dave N is offline   Reply With Quote
Old 03-19-2014, 03:26 PM   #15 (permalink)
Enthusiast Member
 
km1346's Avatar
 
Join Date: Aug 2013
Location: Dallas, TX
Posts: 370
Drives: 40th Anniversary
Rep Power: 12
km1346 is on a distinguished road
Default

I have the wiring done an I am currently using my stock bulbs.. I tired to order switch back LED's from autolumination but they don't sell the 22Watt AO ones anymore in the 3157 Wedge and all the bulbs on ebay look decent but idk if they will fit.

any help on where i could find the best quality bulbs with the perfect size? thanks for the help.
__________________
2010 Nissan 370z 40th Anniversary Build #785
Mods: F.I. CF CBE 12' | Berk HFC | Stillen Gen 3 | Z1 25 Row Oil Cooler | UpRev Tuned | CF Lip/ CF Rear Spats/ CF Diffuser/CF Side Blades
km1346 is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Need help deciding an AMP wiring kit. kentstuh Audio & Video 15 06-25-2013 06:24 PM
Sub Wiring cfleming2226 Audio & Video 4 01-27-2011 10:43 AM
Wiring Help! Gmendez Audio & Video 12 11-10-2010 02:27 PM
re-wiring to keep vdc off boosted180 DIY Section (Do-It-Yourself) 26 02-01-2010 12:12 PM
Wiring adapter? 1slow370 Audio & Video 11 01-06-2010 03:56 PM


All times are GMT -5. The time now is 02:48 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO 3.6.0 PL2