What ramp do you use?

anthonyy

anthonyy

nice DIY! I'm just too lazy for this and they're not stackable!
Either way, looks great.

Dustin@Z1

I can vouch for those particular plastic ramps. I have a set that I use for my 2006 Dodge Ram 2500 Diesel. I use them to tilt trailers to make hauling cars easier. I like how you can stack them together like SOLO cups, taking up less room in the trailer or garage.

bigdog1250

I went ahead an purchased a set of the rhinoramps as everyone seems to love them. I know I'll have to use a 2x4 to set-up onto the ramp, for for $40 you can't beat them.

Time to finish my sway bar install, oil cooler install, and oil change

Mike

I have these:
TAKADA LDS

Car too low for a hydraulic jack to fit under? Use these low down slopes to help raise up your vehicle.

These plastic car ramps are sold in sets of 2 and also work great for those low profile cars that you need just a small amount of lift to get a hydraulic jack under the body or ground effects kits.

These plastic ramps are the only solution for cars with expensive ground effects for getting a jack under the vehicle to lift it for an oil change or other undercarriage service. Whether you are working on you car in the garage or if you are a full blown auto service center, you will find these low cost plastic car ramps offer many uses for the automobile enthusiast or service center.

Made from recycled Takata race belts

__________________
NISSAN: 75 280Z / 86 300ZX GLL /87 Sentra SE / 03 350Z / 23 Z
Porsche: 93 968 / 23 Macan GTS / 93 968

Dwight Frye

After seeing the photo that anthonyy posted I'm tempted to buy another set of Rhino ramps and use them the same way when I do the transmission and differential oil changes. I think if I drove the front wheels up first and then used a floor jack under the differential I could jack up the car, slide the rear ramps under the tires and lower the floor jack. They are about the same cost as jack stands and the adapters for the pinch welds and seem like there is less chance of underbody damage, plus they would keep the car level during the oil change process. Anyone see a flaw in this method ?

bigdog1250

Why not just drive up all 4 at once? With the help of someone to make sure they don't slide out.

djtodd

Please video that!

kenchan

i use the cheapo rhino ramps + extensions i made. i just screw them onto the rhino when i need the extra angle.

XwChriswX

Race ramps are too damned expensive. $475 for the extended 2 piece and the lowering extensions... Eff that.

__________________

Bonnie - Stage 2, Audio build coming this fall!
R.I.P. Abby 3/29/10 - 3/30/14

Dustin@Z1

I have driven up on 4 ramps at the same time with trucks and minivans. But a Z...

A truck/minivan (if it falls off) will not whack the ramp with the fasica or rocker panel. A Z is another story.

anthonyy

yeah that would be a mess lol

kenchan

my cars are on flatstoppers right now from raceramps and they are of high quality.

the thing that ruins it for me on their ramps for lower cars is it's too damn big for storage. i know it breaks up into 2-3 pieces, but too long, too big.

Race Ramps Xtenders - RR-XT Lowered Car Ramps.

Dwight Frye

I'm nervous enough driving up just the front ramps ! No way am I going to try and drive up all 4. I was planning on using the rear 2 as jackstand replacements. But I'm sure it would make a good Youtube video if I failed.

NissanGuy23

I use rhino ramps, two at the front, but i can't get up them without the lip hitting, so i put a 2x4 in front of them and then my lip clears by like 1/8" or maybe just touches it