Fly1Motorsports RS1 Install!!! & OEM Fender Removal

Nut_N_Much · 10-29-2012, 07:25 PM

Looking good brother...

pfdaxe · 11-05-2012, 09:41 PM

Nice

Mr&Mrs · 11-06-2012, 05:14 AM

Check back soon I will be updating with finished product.

pfdaxe · 11-08-2012, 10:34 PM

Ok guys. I just finished installing one of my UAM vented fenders and it was pretty straight forward (thanks to this write-up).

The only thing different, I didn't remove the bumper or the headlights. I just removed the bolt that holds the bumper to the fender and pulled it back a little bit to gain access to the fender bolts that are below the headlight. I then removed the rear top bolt by the door instead of just loosening it like stated. This allowed me to pull the fender out from the rear. This way the fender at the front came off of the headlight without removing it. It saved a couple of steps. Now....the side skirt was another story. The clips are on there tight. I left the clips off when I reinstalled due to the fact I'm replacing them in about 3 weeks with some BSD skirts. Also, you can remove side turn signal before removing fender. It pops out very easily with a small flat head screw driver. It fits carefully between the light and the fender on both sides. Came right out...

Mr&Mrs · 11-11-2012, 12:36 PM

Dont judge my horrible stance people still adjusting my coilovers. New wheels are also on the way....so this is just to display the fenders haha

I will post better pics soon.

Mr&Mrs · 11-11-2012, 12:40 PM

Im also going to get a couple pics when my front wheels are off again of how I cut the rear half of the fender liner. I could not make myself leave it out. I made kind of a cut that looks like this [ (that would be the driver side).

Vichtz · 11-11-2012, 04:39 PM

NICE! I wonder what these fenders would look like color matched all the way, no black

Mr&Mrs · 11-11-2012, 05:13 PM

Im sure they would look just as sexy. I bet someone could do a quick Photoshop of that real quick.

martin82 · 11-12-2012, 01:01 AM

Sorry car is so dirty, I'll have more pics another week been too busy going to the track the last few months!!

Huge thumbs up to fly1motorsports, I had these bad *** fenders sitting in my room for months and just got them installed by them! Couldn't be happier, just need to finish the wrap!

---
I am here: http://maps.google.com/maps?ll=34.157712,-118.465740

martin82 · 11-12-2012, 01:02 AM

Excuse the wheels etc lol, need to go to the dealer so removed my recaro seats and wheels!!

I forgot to mention, I have tested them to 140/145mph (closed road offcourse!) held up great with no problems!!

---
I am here: http://maps.google.com/maps?ll=34.157783,-118.465380

Mr&Mrs · 11-12-2012, 04:54 AM

Martin what wing do you have? Fenders look great!

Edit: I think it is the Nismo wing but it looks different without anything else Nismo.

Vichtz · 11-12-2012, 09:20 AM

you guys! your cars look great! for real!

Mr&Mrs · 11-12-2012, 09:24 AM

Thanks! I hope to have some pro shots taken by the end of the year once this phase of mods are complete.

martin82 · 11-12-2012, 01:54 PM

sorry to jack your thread lol!. The wing is a seibon CF somewhat replica of the nismo.

Mr&Mrs, does your front mud guard scrape at all? After a few high speed tests mine need to be clipped on better but my car is super low.

Mr&Mrs · 11-12-2012, 02:00 PM

Dont worry about going off course I started it! I thought it was the nismo but couldnt really tell.

In the pictures posted above they were rubbing the entire time I was driving. It was only 2" or less off of the gound though. Im at 3.5" right now and they are about 1/2-1" off of the ground and only scrape when I hit a bump.

10-29-2012, 07:25 PM	#16 (permalink)
Nut_N_Much A True Z Fanatic Join Date: Dec 2011 Location: Pensacola Florida Posts: 1,696 Drives: Awesome Car Rep Power: 27	Looking good brother... __________________ Did new cool science stuff to the car !!! http://www.the370z.com/mazoc/99606-z...y-14-17-a.html http://www.the370z.com/diy-section-d...-w-videos.html

11-05-2012, 09:41 PM	#17 (permalink)
pfdaxe A True Z Fanatic Join Date: Aug 2012 Location: Phoenix, AZ Posts: 1,067 Drives: 09 Touring AT Sport Rep Power: 16	Nice __________________ Build Thread: http://www.the370z.com/members-370z-...xes-build.html

11-06-2012, 05:14 AM	#18 (permalink)
Mr&Mrs A True Z Fanatic Join Date: May 2010 Location: Tampa Posts: 4,207 Drives: RZ34 Rep Power: 31940	Check back soon I will be updating with finished product. MIGHTYMOUSE and Nut_N_Much like this. __________________ Project Z <--Click - Check out the link too many mods to list!

11-08-2012, 10:34 PM	#19 (permalink)
pfdaxe A True Z Fanatic Join Date: Aug 2012 Location: Phoenix, AZ Posts: 1,067 Drives: 09 Touring AT Sport Rep Power: 16	Ok guys. I just finished installing one of my UAM vented fenders and it was pretty straight forward (thanks to this write-up). The only thing different, I didn't remove the bumper or the headlights. I just removed the bolt that holds the bumper to the fender and pulled it back a little bit to gain access to the fender bolts that are below the headlight. I then removed the rear top bolt by the door instead of just loosening it like stated. This allowed me to pull the fender out from the rear. This way the fender at the front came off of the headlight without removing it. It saved a couple of steps. Now....the side skirt was another story. The clips are on there tight. I left the clips off when I reinstalled due to the fact I'm replacing them in about 3 weeks with some BSD skirts. Also, you can remove side turn signal before removing fender. It pops out very easily with a small flat head screw driver. It fits carefully between the light and the fender on both sides. Came right out... BeemaaZ likes this. __________________ Build Thread: http://www.the370z.com/members-370z-...xes-build.html Last edited by pfdaxe; 11-10-2012 at 09:07 PM.

11-11-2012, 12:36 PM	#20 (permalink)
Mr&Mrs A True Z Fanatic Join Date: May 2010 Location: Tampa Posts: 4,207 Drives: RZ34 Rep Power: 31940	Dont judge my horrible stance people still adjusting my coilovers. New wheels are also on the way....so this is just to display the fenders haha I will post better pics soon. zero, Eagle, MACSIMIZER and 3 others like this. __________________ Project Z <--Click - Check out the link too many mods to list!

11-11-2012, 12:40 PM	#21 (permalink)
Mr&Mrs A True Z Fanatic Join Date: May 2010 Location: Tampa Posts: 4,207 Drives: RZ34 Rep Power: 31940	Im also going to get a couple pics when my front wheels are off again of how I cut the rear half of the fender liner. I could not make myself leave it out. I made kind of a cut that looks like this [ (that would be the driver side). Amuse370 likes this. __________________ Project Z <--Click - Check out the link too many mods to list!

11-11-2012, 04:39 PM	#22 (permalink)
Vichtz Track Member Join Date: May 2012 Location: Unknown Posts: 538 Drives: PG 09 Nissan 370z Rep Power: 14	NICE! I wonder what these fenders would look like color matched all the way, no black __________________ очень быстро ... Stillen Gen 3 CAI// Stillen CBE// B&M SS with PWJDM Shift Knob// Custom OCC// Drilled/Slotted Rotors//Halo/painted Headlights// Under-hood dress up

11-11-2012, 05:13 PM	#23 (permalink)
Mr&Mrs A True Z Fanatic Join Date: May 2010 Location: Tampa Posts: 4,207 Drives: RZ34 Rep Power: 31940	Im sure they would look just as sexy. I bet someone could do a quick Photoshop of that real quick. __________________ Project Z <--Click - Check out the link too many mods to list!

11-12-2012, 01:02 AM	#25 (permalink)
martin82 A True Z Fanatic Join Date: Nov 2011 Location: los angeles Posts: 2,636 Drives: 12 Nissan 370Z MB M6 Rep Power: 20	Excuse the wheels etc lol, need to go to the dealer so removed my recaro seats and wheels!! I forgot to mention, I have tested them to 140/145mph (closed road offcourse!) held up great with no problems!! --- I am here: http://maps.google.com/maps?ll=34.157783,-118.465380

11-12-2012, 04:54 AM	#26 (permalink)
Mr&Mrs A True Z Fanatic Join Date: May 2010 Location: Tampa Posts: 4,207 Drives: RZ34 Rep Power: 31940	Martin what wing do you have? Fenders look great! Edit: I think it is the Nismo wing but it looks different without anything else Nismo. __________________ Project Z <--Click - Check out the link too many mods to list! Last edited by Mr&Mrs; 11-12-2012 at 09:25 AM.

11-12-2012, 09:20 AM	#27 (permalink)
Vichtz Track Member Join Date: May 2012 Location: Unknown Posts: 538 Drives: PG 09 Nissan 370z Rep Power: 14	you guys! your cars look great! for real! Mr&Mrs likes this. __________________ очень быстро ... Stillen Gen 3 CAI// Stillen CBE// B&M SS with PWJDM Shift Knob// Custom OCC// Drilled/Slotted Rotors//Halo/painted Headlights// Under-hood dress up

11-12-2012, 09:24 AM	#28 (permalink)
Mr&Mrs A True Z Fanatic Join Date: May 2010 Location: Tampa Posts: 4,207 Drives: RZ34 Rep Power: 31940	Thanks! I hope to have some pro shots taken by the end of the year once this phase of mods are complete. __________________ Project Z <--Click - Check out the link too many mods to list!

11-12-2012, 01:54 PM	#29 (permalink)
martin82 A True Z Fanatic Join Date: Nov 2011 Location: los angeles Posts: 2,636 Drives: 12 Nissan 370Z MB M6 Rep Power: 20	sorry to jack your thread lol!. The wing is a seibon CF somewhat replica of the nismo. Mr&Mrs, does your front mud guard scrape at all? After a few high speed tests mine need to be clipped on better but my car is super low.

11-12-2012, 02:00 PM	#30 (permalink)
Mr&Mrs A True Z Fanatic Join Date: May 2010 Location: Tampa Posts: 4,207 Drives: RZ34 Rep Power: 31940	Dont worry about going off course I started it! I thought it was the nismo but couldnt really tell. In the pictures posted above they were rubbing the entire time I was driving. It was only 2" or less off of the gound though. Im at 3.5" right now and they are about 1/2-1" off of the ground and only scrape when I hit a bump. __________________ Project Z <--Click - Check out the link too many mods to list!

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Fender removal	rjsf	Exterior & Interior	9	10-20-2012 06:01 PM
any diy or instruction for Fender install?	martin82	Exterior & Interior	15	10-07-2012 05:15 PM
DENT REMOVAL & FENDER ROLL DAY Oct.8,2011, Fremont, CA	sid67jp	Northern California Region	6	10-07-2011 08:07 PM
Sport lip OEM removal/install	tjlazer	Exterior & Interior	2	03-26-2010 11:56 PM
Fender Liner Removal?	blinkme323	DIY Section (Do-It-Yourself)	1	02-01-2010 07:32 AM