DIY: Oil Pan Spacer

weiboy718 · 08-29-2010, 11:33 AM

sorry for bringing this back up! do you know where the dip stick level is suppose to register at? mines reading over the high mark but my oil pressure is very normal.

weiboy718 · 08-29-2010, 09:45 PM

this might help out others that wanna do this. for the frame you don't have to cut it. just bend it back a lil for clearance so you can install your bolt.

after you get your bolt up there use an angle socket to screw it in and torque it down to spec.

lastly, just try to bend it back or use a small wood to hammer it back.

OP, you can copy these pic's and update it to your first post if you want.

wstar · 04-12-2011, 11:45 PM

Quote:

Originally Posted by weiboy718

sorry for bringing this back up! do you know where the dip stick level is suppose to register at? mines reading over the high mark but my oil pressure is very normal.

You should be using the dipstick just like normal. Thinking about it visually: you're adding depth at the bottom of the pan, and you're dropping down the oil pump's pickup tube by the same amount, but you want the oil level relative to the lower engine components to remain the same (which is why the dipstick didn't move). Having your oil overfilled too much (by the dipstick) can cause frothing of your oil, which isn't great for lubrication.

Thanks for the update/pics on bending that corner tab. Much better solution than mine (cutting it off), guess I'm just an impatient careless bastard sometimes

. I'll link it back to the top so nobody else misses it.

BGTV8 · 04-13-2011, 03:13 AM

I have had tis exact combination in my car for the last 2 years ... I never have issues on the track and daily driving in Melbourne (Australa) summer (regualr 40Deg C temps) never see oil temps above105 DegC

Track temps nefer exceed 115-120DegC.

Simple and very effective mod.

RB

diddy535 · 03-01-2012, 10:58 AM

Does anybody know if the cover will still fit with the spacer?

Rusty · 03-01-2012, 07:16 PM

Quote:

Originally Posted by diddy535

Does anybody know if the cover will still fit with the spacer?

If you are talking about the bottom cover. It fits on mine with no problems.

diddy535 · 03-02-2012, 12:19 PM

Quote:

Originally Posted by Rusty

If you are talking about the bottom cover. It fits on mine with no problems.

Yeah I was, thanks!

Spartan 1771 · 10-01-2017, 08:42 PM

I'm not sure if anyone is still monitoring this thread, but I figured i would give it a shot.

I'm in the middle of an oil pan upgrade and I scraped the underside of the engine where it meets the pan. Since I'm upgrading the pan, I didn't care about the oem pan getting damaged so I pried it off using a chisel and a flathead screw driver. You can see the damage in the pic. I'm thinking about sanding it down very lightly. Since the ultra grey gasket sealer actually maintains the seal, does anyone think this will cause an oil leak once the new pan is on?

Spartan 1771 · 10-01-2017, 08:44 PM

Also, will gasket remover damage the bottom of the engine? I know it will take the paint off of the pan, but since the engine isn't painted, I was considering using it to take off the reminanents of the oem seal.

Rusty · 10-01-2017, 08:50 PM

Take a flat file. And file that down. MAKE sure to hold the file flat against the surface. It won't take much effort. Looks like you have one gouge on the right side of the picture that goes all across the mating surface. That's where you need to keep it clean when you put RTV on.

Rusty · 10-01-2017, 08:54 PM

Quote:

Originally Posted by Spartan 1771

Also, will gasket remover damage the bottom of the engine? I know it will take the paint off of the pan, but since the engine isn't painted, I was considering using it to take off the reminanents of the oem seal.

Use a razor blade scrapper to remove the RTV. It will come off stringy. Then hand wire brush.

Sometimes the spray on gasket remover will not work on some RTV's.

Spartan 1771 · 10-01-2017, 08:56 PM

Quote:

Originally Posted by Rusty

Take a flat file. And file that down. MAKE sure to hold the file flat against the surface. It won't take much effort. Looks like you have one gouge on the right side of the picture that goes all across the mating surface. That's where you need to keep it clean when you put RTV on.

Rusty! Thank You for the fast response! I'm over here freaking out about this. It's nice to know there are always people in here willing to help.

Just to be clear:
Remove the oem gasket first, use a flat file gently across the entire front surface to even it all out. Then use the rtv to seal it properly.

Rusty · 10-01-2017, 09:01 PM

Quote:

Originally Posted by Spartan 1771

Rusty! Thank You for the fast response! I'm over here freaking out about this. It's nice to know there are always people in here willing to help.

Just to be clear:
Remove the oem gasket first, use a flat file gently across the entire front surface to even it all out. Then use the rtv to seal it properly.

Fast learner.

If you have a file that is wider then the surface width. Use that. Less chance of creating a low spot.

Spartan 1771 · 10-01-2017, 09:03 PM

Thanks again!

Rusty · 10-01-2017, 09:04 PM

Quote:

Originally Posted by Spartan 1771

Thanks again!

10-01-2017, 08:42 PM	#23 (permalink)
Spartan 1771 A True Z Fanatic Join Date: Nov 2009 Location: Western Maryland Posts: 1,280 Drives: Wife crazy & 09 370Z Rep Power: 105454	I'm not sure if anyone is still monitoring this thread, but I figured i would give it a shot. I'm in the middle of an oil pan upgrade and I scraped the underside of the engine where it meets the pan. Since I'm upgrading the pan, I didn't care about the oem pan getting damaged so I pried it off using a chisel and a flathead screw driver. You can see the damage in the pic. I'm thinking about sanding it down very lightly. Since the ultra grey gasket sealer actually maintains the seal, does anyone think this will cause an oil leak once the new pan is on? __________________ ~Rob -DD Air Guide, Stillen G3 CAIs, 63mm Throttle Bodies, Motordyne M370, Berk HFCs, FI TDX CBE (non-res, CF), Sprint booster v3, Ecutek Dyno Tuned, and the list goes on...

10-01-2017, 08:44 PM	#24 (permalink)
Spartan 1771 A True Z Fanatic Join Date: Nov 2009 Location: Western Maryland Posts: 1,280 Drives: Wife crazy & 09 370Z Rep Power: 105454	Also, will gasket remover damage the bottom of the engine? I know it will take the paint off of the pan, but since the engine isn't painted, I was considering using it to take off the reminanents of the oem seal. __________________ ~Rob -DD Air Guide, Stillen G3 CAIs, 63mm Throttle Bodies, Motordyne M370, Berk HFCs, FI TDX CBE (non-res, CF), Sprint booster v3, Ecutek Dyno Tuned, and the list goes on...

10-01-2017, 08:50 PM	#25 (permalink)
Rusty Ronin Samurai - Assassin Join Date: Dec 2011 Location: Fayettenam,Pennsyltucky Age: 68 Posts: 35,217 Drives: 2011 Nismo GM 6M Rep Power: 2684438	Take a flat file. And file that down. MAKE sure to hold the file flat against the surface. It won't take much effort. Looks like you have one gouge on the right side of the picture that goes all across the mating surface. That's where you need to keep it clean when you put RTV on. Spartan 1771 likes this. __________________ 浪人 - 殺し屋 "The Difficult Anytime, The Impossible By Appointment Only" http://www.the370z.com/members-370z-...o-journal.html

10-01-2017, 09:03 PM	#29 (permalink)
Spartan 1771 A True Z Fanatic Join Date: Nov 2009 Location: Western Maryland Posts: 1,280 Drives: Wife crazy & 09 370Z Rep Power: 105454	Thanks again! Rusty likes this. __________________ ~Rob -DD Air Guide, Stillen G3 CAIs, 63mm Throttle Bodies, Motordyne M370, Berk HFCs, FI TDX CBE (non-res, CF), Sprint booster v3, Ecutek Dyno Tuned, and the list goes on...

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
plenum spacer/ t.b. spacer	jnaut	Intake/Exhaust	56	08-08-2013 03:57 AM
In need of a 7mm spacer	igota21incher	Wheels & Tires	6	04-09-2012 01:10 PM
more spacer help	urdeliveryguy	Wheels & Tires	0	03-26-2012 09:50 PM
[WTB] a pair of 15mm spacer and a pair of 20mm spacer	scottnismo	Parts for sale (Private Classifieds)	0	12-20-2011 12:21 PM
SEEN THIS? Oil Pan Spacer Now Available	BrickyardZ	Engine & Drivetrain	9	01-22-2011 10:58 AM

08-29-2010, 11:33 AM	#16 (permalink)
weiboy718 Track Member Join Date: May 2010 Location: Bay Area Posts: 923 Drives: Infiniti G37 Rep Power: 16	sorry for bringing this back up! do you know where the dip stick level is suppose to register at? mines reading over the high mark but my oil pressure is very normal.

08-29-2010, 09:45 PM	#17 (permalink)
weiboy718 Track Member Join Date: May 2010 Location: Bay Area Posts: 923 Drives: Infiniti G37 Rep Power: 16	this might help out others that wanna do this. for the frame you don't have to cut it. just bend it back a lil for clearance so you can install your bolt. after you get your bolt up there use an angle socket to screw it in and torque it down to spec. lastly, just try to bend it back or use a small wood to hammer it back. OP, you can copy these pic's and update it to your first post if you want.

04-13-2011, 03:13 AM	#19 (permalink)
BGTV8 A True Z Fanatic Join Date: Dec 2009 Location: 03350 Australia Posts: 1,514 Drives: 09 Nissan 370Z M6 Rep Power: 39973	I have had tis exact combination in my car for the last 2 years ... I never have issues on the track and daily driving in Melbourne (Australa) summer (regualr 40Deg C temps) never see oil temps above105 DegC Track temps nefer exceed 115-120DegC. Simple and very effective mod. RB

03-01-2012, 10:58 AM	#20 (permalink)
diddy535 Track Member Join Date: Feb 2012 Location: St. Louis, MO Posts: 789 Drives: '09 370Z RAE 6MT Rep Power: 14	Does anybody know if the cover will still fit with the spacer?