DIY: Headlight LED's and blackout

pfdaxe · 10-20-2013, 01:50 PM

Quote:

Originally Posted by Smartace3

For those of you that used Krylon fusion paint.. How has it been holding up?? Any chipping, peeling, cracking, fading from the heat of the lights?? Im planning on doing this to my headlights and wanted to know the best route to take. Thanks.

Paint still looks as good as day one. No issues.

Smartace3 · 10-21-2013, 05:30 PM

Quote:

Originally Posted by pfdaxe

Paint still looks as good as day one. No issues.

Did you just scuff and apply the Krylon fusion paint or did you use adhesion promoter/primer? If so what kind of primer??

pfdaxe · 10-21-2013, 06:20 PM

Quote:

Originally Posted by Smartace3

Did you just scuff and apply the Krylon fusion paint or did you use adhesion promoter/primer? If so what kind of primer??

Just cleaned it and painted it

Dozier · 11-03-2013, 09:40 AM

Just ordered my paint online to match my car. Can't wait for it to arrive. Not doing LEDs. Just doing black out housings with Red color matched rings.

Dozier · 11-09-2013, 04:19 PM

Can you believe I just tore the whole front end of my car apart and pulled out my headlights. I was going to bake them and black them out on the inside. My headlights do not fit inside my oven. This sucks. I guess I have to go find a heat gun.

1325 · 11-09-2013, 05:02 PM

Quote:

Originally Posted by Dozier

Can you believe I just tore the whole front end of my car apart and pulled out my headlights. I was going to bake them and black them out on the inside. My headlights do not fit inside my oven. This sucks. I guess I have to go find a heat gun.

Trust me on this, you're certainly not alone.

Kabestro · 11-09-2013, 06:07 PM

Does anyone know how I adjust my headlights? Do I need to remove the rubber cover inside the engine bay?

SouthArk370Z · 11-09-2013, 07:09 PM

Quote:

Originally Posted by Kabestro

Does anyone know how I adjust my headlights? Do I need to remove the rubber cover inside the engine bay?

Download the Factory Service manual (see link in my sig). It has procedures for doing just about any maintenance you can imagine.

Kabestro · 11-09-2013, 08:14 PM

Quote:

Originally Posted by SouthArk370Z

Download the Factory Service manual (see link in my sig). It has procedures for doing just about any maintenance you can imagine.

Thanks, I'm assuming the 2012 manual should be the same for the 2013 model concerning the headlights.

SouthArk370Z · 11-09-2013, 09:38 PM

Quote:

Originally Posted by Kabestro

Thanks, I'm assuming the 2012 manual should be the same for the 2013 model concerning the headlights.

I don't know but, if not exactly the same, they should be close enough that you can figure it out.

Dozier · 11-11-2013, 02:38 PM

I used the cardboard box and heat gun method instead of the oven.

RZ14 · 02-13-2014, 06:28 PM

Quote:

Originally Posted by cperusa

Here are the pics of my 40th after headlight mod...
Headlights painted with color matched paint.
1.

2.

The LEDs
3.

evil look
4.

Where did you acquire the paint for the housing?

Dozier · 02-13-2014, 06:31 PM

Automotivetouchup.com

Sent from my HTC One X+ using Tapatalk

ka24king · 02-28-2014, 10:57 AM

Does anyone have another picture of how to wore it to the day time running lights?!?!!!! I'm sorry but I have been staring at that picture for about an hour as have read the instructions no less that 25 times and still just don't get it at all. Also I'd like to add I have 0% electrical background

SouthArk370Z · 02-28-2014, 11:29 AM

Quote:

Originally Posted by ka24king

Does anyone have another picture of how to wore it to the day time running lights?!?!!!! I'm sorry but I have been staring at that picture for about an hour as have read the instructions no less that 25 times and still just don't get it at all. Also I'd like to add I have 0% electrical background

Maybe you need to find someone that knows what they are doing and hire/barter them. A botched wiring job can get very expensive on a modern, computer-controlled car. If it were a 280Z, you'd blow a fuse and maybe burn up a wire - fairly cheap to fix. On a 370Z, you run the risk of frying the IPDM or BCM or ...

11-09-2013, 06:07 PM	#217 (permalink)
Kabestro Enthusiast Member Join Date: Aug 2012 Location: Puerto Rico Posts: 331 Drives: 13 Nissan 370Z MR M6 Rep Power: 40	Does anyone know how I adjust my headlights? Do I need to remove the rubber cover inside the engine bay? __________________ Stillen Gen 3 CAI / Fast Intentions HFC and CBE 12" Res. (#730) / Swift Springs / 20mm H&R Spacers / Clutch Helper Spring / UpRev Tune 322whp.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
DIY: Headlight Removal	DIGItonium	DIY Section (Do-It-Yourself)	34	09-03-2017 08:01 PM
180 Custom Headlight Review!	bullitt5897	Exterior & Interior	43	12-10-2010 05:26 PM
Blacked out headlight for PG !!!	msl82	Exterior & Interior	31	05-02-2009 06:06 PM
Blacked out headlight	msl82	Nissan 370Z General Discussions	6	01-02-2009 12:47 PM

11-03-2013, 09:40 AM	#214 (permalink)
Dozier Base Member Join Date: Oct 2013 Location: Birmingham, Al Posts: 222 Drives: 09 Nismo 370Z Rep Power: 12	Just ordered my paint online to match my car. Can't wait for it to arrive. Not doing LEDs. Just doing black out housings with Red color matched rings.

11-09-2013, 04:19 PM	#215 (permalink)
Dozier Base Member Join Date: Oct 2013 Location: Birmingham, Al Posts: 222 Drives: 09 Nismo 370Z Rep Power: 12	Can you believe I just tore the whole front end of my car apart and pulled out my headlights. I was going to bake them and black them out on the inside. My headlights do not fit inside my oven. This sucks. I guess I have to go find a heat gun.

02-13-2014, 06:31 PM	#223 (permalink)
Dozier Base Member Join Date: Oct 2013 Location: Birmingham, Al Posts: 222 Drives: 09 Nismo 370Z Rep Power: 12	Automotivetouchup.com Sent from my HTC One X+ using Tapatalk

02-28-2014, 10:57 AM	#224 (permalink)
ka24king Track Member Join Date: Feb 2013 Location: texas Posts: 582 Drives: '10 370z 40th annv. Rep Power: 13	Does anyone have another picture of how to wore it to the day time running lights?!?!!!! I'm sorry but I have been staring at that picture for about an hour as have read the instructions no less that 25 times and still just don't get it at all. Also I'd like to add I have 0% electrical background