DIY: Fang Vents: Forced fresh air to your airbox

NIZMOZ · 07-13-2009, 08:39 AM

Quote:

Originally Posted by Modshack

Ummm...Everything was listed at the top of the album page:

(4) 2.5" aluminum flanges P/N 10350-10
(6) foot Aeroduct hose P/N 05-29810
(4) Stainless clamps

From: Http://www.aircraftspruce.com

Thanks for the info. As I mentioned it is not on your page. Here is all that was mentioned.

"Brake cooling project in the works. Cost $16 per side using a shop vac nozzle, 2 1/2 flanges from Pilot Supplies, Avionics, and Homebuilt Aircraft Parts from Aircraft Spruce and Specialty Co. (part # 10350-10 $6.80) and some 2 1/2 hose.

Testing resulted in a 10-12% reduction in rotor temps under normal driving conditions (stops to measure temps with an IR thermometer)"

Modshack · 07-13-2009, 02:40 PM

Quote:

Originally Posted by NIZMOZ

Thanks for the info. As I mentioned it is not on your page. Here is all that was mentioned.

"

Ah...OK...Didn't realize you were referring to the Brake Mod (since this thread didn't start out that way), but the parts for the Fang vents are the same Plus a few shop vac nozzles from Home Depot. You won't need as much hose either, but I'd buy that much anyway.....

bigaudiofanat · 07-13-2009, 03:16 PM

You should always have a filter to clean the air before it goes into your engine

NIZMOZ · 07-13-2009, 03:41 PM

Quote:

Originally Posted by Modshack

Ah...OK...Didn't realize you were referring to the Brake Mod (since this thread didn't start out that way), but the parts for the Fang vents are the same Plus a few shop vac nozzles from Home Depot. You won't need as much hose either, but I'd buy that much anyway.....

My plan is to run it from my area of the grill like you did but to the brakes as I have the Injen CAIs which has the filters down there already. I just have to figure out a way to mount the hose and adapter to the bumper in that area as it isn't flat like yours is.

Modshack · 07-14-2009, 04:59 PM

Quote:

Originally Posted by bigaudiofanat

You should always have a filter to clean the air before it goes into your engine

Huh?...All this stuff is pre-filter. Doesn't matter what you have..Stock or otherwise. It's simply a means to get outside (and cooler) air to the filter inlet..

bboypuertoroc · 07-14-2009, 06:36 PM

Quote:

Originally Posted by Modshack

Huh?...All this stuff is pre-filter. Doesn't matter what you have..Stock or otherwise. It's simply a means to get outside (and cooler) air to the filter inlet..

Don't know why people keep faling to realize this setup is NOT in place of filters...

Awesome write-up Mod. Definitely will be doing this once I get my next Z.

+rep to you sir.

blackbird · 07-16-2009, 08:56 PM

Why wouldn't I do the same setup for Stillen Gen 3 long tube as was done for the brake? Actually asking about using the Shop vac aimed at the filter. That Shop vac bit was brilliant. I had been contemplating adding some vents in the nose until I saw this thread.

john0990 · 07-22-2009, 05:36 PM

Very nice writeup. I too would be interested in routing the hose to the brakes. I have been told by more than one race shop that when doing ducting for any car, they only recommend routing air to the center of the rotor, so that it can blow from the inside out through the cooling vanes. Blowing air directly on the inside of the rotor will result in only that side being cooler, which puts uneven heat/stress on both rotors and pads.

Here is one example of a kit for BMW M3:
Turner Motorsport - Item# TMSBRAKE46 - TMS E46 Racing Brake Duct Kit - E46

I wonder if there is enough room to come up with a similar solution for the 370Z?

blackbird · 08-15-2009, 10:34 PM

Just had the Modshack mods done for the Fang vents for the Stillen Gen 3. Just want to say thanks for the concept to Modshack. Kudos.

Shunya · 08-16-2009, 12:35 AM

Quote:

Originally Posted by john0990

Very nice writeup. I too would be interested in routing the hose to the brakes. I have been told by more than one race shop that when doing ducting for any car, they only recommend routing air to the center of the rotor, so that it can blow from the inside out through the cooling vanes. Blowing air directly on the inside of the rotor will result in only that side being cooler, which puts uneven heat/stress on both rotors and pads.

Here is one example of a kit for BMW M3:
Turner Motorsport - Item# TMSBRAKE46 - TMS E46 Racing Brake Duct Kit - E46

I wonder if there is enough room to come up with a similar solution for the 370Z?

that would definitely be nice~!

ZForce · 09-05-2009, 02:05 AM

Looking to have the vents done soon. I am wondering how much cooler air will get through on a Injen CAI versus the Stillen G3 CAI being they are mounted in different areas.

Modshack · 09-06-2009, 10:23 AM

Quote:

Originally Posted by ZForce

Looking to have the vents done soon. I am wondering how much cooler air will get through on a Injen CAI versus the Stillen G3 CAI being they are mounted in different areas.

You just need to aim the hoses or ducting at your filter. A left and right 90 degree angle off the fang holes, pointed toward you injen should work..

ZForce · 09-07-2009, 12:18 AM

Quote:

Originally Posted by Modshack

You just need to aim the hoses or ducting at your filter. A left and right 90 degree angle off the fang holes, pointed toward you injen should work..

Thanks a bunch, I may pm you if I have any questions on the install or parts. I did check out your album.

btw...props in advance for this great contribution to the community.

ResIpsa · 10-08-2009, 02:38 PM

Here is a slight variation that will save you $17 on installation.

I used 2.5 inch neoprene brake duct hose from Porterfield brake company. Rather than attaching a set of flanges to the air pass through I just jammed the hose directly into the airbox. With a little flexing of the hose it fits in perfectly.

The last picture is one taken with my cell phone directly into the airbox.

Oh, yeah. I also routed the hoses around the outside of the crash bar. This required removing the air deflectors.

simota1 · 10-15-2009, 09:53 AM

gonna finally do this mod today

07-13-2009, 03:16 PM	#33 (permalink)
bigaudiofanat Car Audio Installer Join Date: Jun 2009 Location: Magnolia DE Posts: 8,342 Drives: 2012 Infiniti G37x Rep Power: 853	You should always have a filter to clean the air before it goes into your engine __________________ Need help with car audio or electronics? Let me know!! Need Help Let Me Know Direct email address reimermatt@gmail.com Owner of: Dynamic Mobile Audio Follow me below https://www.facebook.com/Dynamicmobileaudio/

10-15-2009, 09:53 AM	#45 (permalink)
simota1 A True Z Fanatic Join Date: May 2009 Location: Dededo, Guam Posts: 6,642 Drives: solid red 370z 6mt Rep Power: 405	gonna finally do this mod today __________________ *TOP SECRET/POWERHOUSE AMUSE/ARC/DAYTONA RACING/VARIS/MINES/GANADOR/J-LINE/WORK EMOTION CR KAI/GT SPEC/CARBON SIGNAL/ZOOM ENGINEERING/ CARBON FIBER ELEMENT/STILLEN/*

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
DIY: Extra air to stock airbox	Mandingo	DIY Section (Do-It-Yourself)	14	03-17-2013 02:35 PM
[FOR SALE] Stock Airbox Assemblies	sixpax	Parts for sale (Private Classifieds)	19	03-12-2013 07:47 PM
Factory Airbox Mod?	ThaMailman	Intake/Exhaust	12	01-26-2011 05:25 PM
Fang Vents: Forced air DIY....>	Modshack	Intake/Exhaust	4	06-29-2009 11:49 AM
Found a prize in my left airbox	molamann	Nissan 370Z General Discussions	17	05-19-2009 09:12 PM

07-16-2009, 08:56 PM	#37 (permalink)
blackbird Base Member Join Date: May 2009 Location: Nashua NH Posts: 179 Drives: 09 370Z BLk GTM TT Rep Power: 16	Why wouldn't I do the same setup for Stillen Gen 3 long tube as was done for the brake? Actually asking about using the Shop vac aimed at the filter. That Shop vac bit was brilliant. I had been contemplating adding some vents in the nose until I saw this thread.

07-22-2009, 05:36 PM	#38 (permalink)
john0990 Base Member Join Date: May 2009 Location: Dallas, tX Posts: 6 Drives: 03 BMW M3 Rep Power: 16	Very nice writeup. I too would be interested in routing the hose to the brakes. I have been told by more than one race shop that when doing ducting for any car, they only recommend routing air to the center of the rotor, so that it can blow from the inside out through the cooling vanes. Blowing air directly on the inside of the rotor will result in only that side being cooler, which puts uneven heat/stress on both rotors and pads. Here is one example of a kit for BMW M3: Turner Motorsport - Item# TMSBRAKE46 - TMS E46 Racing Brake Duct Kit - E46 I wonder if there is enough room to come up with a similar solution for the 370Z?

08-15-2009, 10:34 PM	#39 (permalink)
blackbird Base Member Join Date: May 2009 Location: Nashua NH Posts: 179 Drives: 09 370Z BLk GTM TT Rep Power: 16	Just had the Modshack mods done for the Fang vents for the Stillen Gen 3. Just want to say thanks for the concept to Modshack. Kudos.

09-05-2009, 02:05 AM	#41 (permalink)
ZForce A True Z Fanatic Join Date: Jul 2009 Location: Roseville, CA Posts: 2,359 Drives: 09 370Z Tour + Sport Rep Power: 21	Looking to have the vents done soon. I am wondering how much cooler air will get through on a Injen CAI versus the Stillen G3 CAI being they are mounted in different areas.