DIY: Stainless Steel Clutch Line

SPOHN · 06-20-2011, 07:21 PM

Well after some time I decided to change out my puny stock clutch line to a more efficient stainless steel line from Z1 Motorsports. There pretty cheap part. I think $29 bucks. Plus you need to pick up a bottle Motul RBF600 brake fluild to help the system operate to it's fullest. This mod is best to do if your changing out your Catalytic Converter (Cats) to HFC's or TP's. For they will need to be removed to to this install. I couldn't imagine them being done with them on the car. If you never have removed your Cats I suggest doing some good research first. They could be a pain. But I have been moved. Wasn't a big deal for me, but others have struggled.

14mm socket
Rachet Extension (12'' preferable)
Swivel
14mm wrench (2 works best)
10mm line wrench (standered wrench can work)
10mm socket
8mm wrench
Flathead screwdriver
Pliers

Here in the first pic you'll see the cross member brace that connects to my Test Pipes (TP). They actual connect to both sides of my TP's or Cats, whatever you might have. Plus there's two bolts that help hold the bracket in place to the underside of the transmission. There's four in all. All are 14mm. Use your rachet and socket with your wrench together to remove all. Place to the side. You'll also need to go ahead and unplug the O2 sensor for the driver side. You can see in the pic the passenger side is still hooked up. It can be left alone.

My next two pics you can get a good picture of my TP's. You will need to remove the two 14mm nuts and bolts on the flange in the far left of the first pic using two 14mm wrenches works best for me. And in the second you will see the triangle shaped flange that connects to the maniflold. You will have to remove the three nuts and bolts here also. This is where your rachet, socket, extension, and swivel works best. There are actually two nuts and bolts and the third is just a nut due to there a set bolt already placed in the manifold flange. You can see the different one in the top right of the flange.

Now below are some pics of my TP's removed along with the clutch lines. Look carefull at them. You will noticed the hard line on the inner side of the body, then the rubber line in the middle (has heat shield on it), and then another hard line that connects to the transmission.

Ok. In the pic below (same as above) start to remove this hard line. Start with the silver bracet and black bolt the lays in the middle of the the line. Remove it with a 10mm socket. Then start to remove the hard line form the clutch slave cylinder (the brass colored fitting) using a 10mm line wrench or standard wrench. Just be carefull here for these fittings are usally over tighten from the manufacture and can be strip easly. Even though you will not be reusing this particular line and fittings back for it will not be needed. The new line deletes this part. It has a banjo fiittng that bolts directly to the clutch slave cylinder.

Also have a drip tray ready for just about all the fluid will leak out here. Also in the upper middle part of the pic you will see a pressure clip that will have to be pulled out using a flathead screw driver to pull out. The clip has a lip on that can be pried on. This clip can be tight. See the second pic for better look. The third pic is what you will end up with. Just let all the fluid drain out at this point. Mkae sure the cap is off the reservoir to allow for flow.

Now were going to concentrate on the other end of the the clutch line. This can be tricky here. For it is a tight area to work in being the manifold flange is all in the way. These connection points also have a pressure plate here also. I found it easier to remove the pressure plate first with a flathead. And pull down on the line a litte but not to hard. Don't want to hurt anything. Normally I'd say leave the line in place untill you loosen the line. But there is hardly any room to turn a line wrench in there due to the manifold flange. And being likely over tighten from the manifacture you could easily strip it. I know for I did. I had to order another hard line. It was only $13. But doing it the way I'm describing and some patience you should be fine.

Back to removing. Refer to the second pic. Sorry it's blury. You will see the line pulled down a little. Use some pliers and grip the bigger part of the fitting just above the heat shield. It has two flat edges to grip. Careful of the heat shield for you will reuse it on the new line. Then use a 10mm wrench on the upper nut and losen. Remove line and then remove heat shield by cutting zip ties. The Z1 kit comes with new zip ties.

Now take the new SS clutch line. Comes with a line, banjo bolt (what I call it), two copper washers, and zip ties. Now take the bigger part of the new line and attach it to the the hard line by the manifold flange. It only needs to be tighten to about 12lbs of torque. I just use my best judgement here. Good thing the Z1 line has a hex fitting (19mm) that makes it easier to connect to the hardline. Just reconnect same way you undid. Route the fittings back up into the shelf stub where you pulled the pressure plate from and reinstall it. This can be hard for you have to hold the line even as you press in the clip. I had to hold the line take a flathead screwdriver and pry between the clip and the manifold flage. Be carfull not to slip. Could bust your knuckles.

Now slip the heat shield over the new line. Take the other end of the line (the banjo fitting), banjo bolt, and copper washers ( 2 of them). Use the copper washers on both sides of the banjo fitting and tighten to the clutch slave cylinder (brass fitting). Might have to route the line around to the inside the bleeder screw then tighten. You can see below. Also go ahead zip tie the heat shied tighter to the new line and cut off excess.

Mkae sure everything is tight. Reinstall TP's. Now start to bleed the clutch. Fill the clutch resesvoir with the Motul brake fluid. It's the small cap to the right in the first pic below. Fill up to top. Put cap on. Start pumping clutch alot. You will have to use your hand at first. For once depressed it wont come back up. You also in the begining have to open the bleeder screw to get the fluid to flow down at first. This is where the 8mm wrench comes in. Seal off bleeder screw, pump clutch with hands more. It will take a bit. Keep going back to reservoir to always make sure it doesnt get to low and feel up with air and that your always reinstalling the cap. I feel this is easier than doing the brakes. A lot less fluid and lines. Just keep bleeding till all the old fluid is out and your sure the new fluid is coming threw. Now eventually you will feel the pressure build for it will be alot stiffer than stock. Even though the pressure will build and the clutch will rebound on it's own when you open the bleeder screw the clutch will stick to the floor and you will have to seal off the screw and pull the clutch back up last time. Ensuring the bleeder screw is sealed off pump the clutch some more and pressure will build. Top off the fluid one more last time. Sorry for no pics on this. But I do hope this helps alot.

Again I hope this helps and you guys like my write up. Sorry for any bad grammer. Now enjoy your stiffer feel clutch line. It's a big difference from stock. Combined with the fluid you should have to worry about the clutch sticking to the floor from hard launches and track days.

Any suggestions or questions and comments welcome. Write ups are usally big and easy to leave out some things for it's alot to do.

wheee! · 06-21-2011, 02:08 PM

Is it absolutely necessary to remove the TP's or Cats?

daisuke149 · 06-21-2011, 02:50 PM

good write up Chris.

The TP / HFC doesnt have to be removed. When mine was put it, we did not remove them. Just gotta be able to reach slightly behind them.

SPOHN · 06-21-2011, 03:48 PM

Quote:

Originally Posted by wheee!

Is it absolutely necessary to remove the TP's or Cats?

I assume you could leave them on. I wouldn't want to. I had trouble loosening the bolt up by the manifold on my car. So I had no choice in the manner. It's really easy to remove them. Cats could be harder but even when I removed mine it went well. But my car didn't have many miles on it at the time so I feel that made it easier to break loose the demon bolt everyone speaks of.

Quote:

Originally Posted by daisuke149

good write up Chris.

The TP / HFC doesnt have to be removed. When mine was put it, we did not remove them. Just gotta be able to reach slightly behind them.

Thanks. And thanks again for the other day. Now where's my rep?

daisuke149 · 06-21-2011, 04:11 PM

you mean wheres my rep for giving you directions!!

SPOHN · 06-21-2011, 04:13 PM

Oh yea. Damn! I got yea. I wouldn't of found it without you.

SPOHN · 07-03-2011, 11:01 AM

Week later update. The clutch pedal feels alot better than ever. Great soild feel. Almost gives you confindence. Now if I could just get my softer clutch spring I'll be set.

rambunctious · 02-10-2012, 12:34 PM

How many bottles of brake fluid are needed for this line change?

modme · 02-10-2012, 01:15 PM

Less than 1. The clutch reservoir is tiny. Even with flushing, it shouldnt take more than 1 bottle.

modme · 02-10-2012, 01:15 PM

It looks like you have a gasket leak on your test pipes. Might want to put some RTV over the gaskets.

370Z Purist · 07-09-2012, 09:22 AM

Why isn't this stickied?! This should DEFINITELY be stickied.

scruffydog · 01-14-2013, 09:31 PM

I recently ordered an Insulated S.S. from the Z Store.

Link
Do you think I should do a heat shield over it anyway even though it's insulated? I would think it wouldn't hurt to put a heat shield on anyway, where did you get your heat shield from? Cheers!

SPOHN · 01-14-2013, 09:37 PM

I just reused the stock one. You can get a clutch line from Z1 for $29.
Z1 370z/G37 Stainless Steel Clutch Line

scruffydog · 01-14-2013, 10:25 PM

oh i had no idea the stock one already has a heat shield on it. In that case I'll just use the stock one over the insulated s.s. clutch line i got from the Z store. Thanks!

DarkPath · 05-24-2013, 01:44 PM

Quote:

Originally Posted by scruffydog

oh i had no idea the stock one already has a heat shield on it. In that case I'll just use the stock one over the insulated s.s. clutch line i got from the Z store. Thanks!

the material on the S.S. clutch line from Z1 depicted here is not heat shield, its merely a coating meant to prevent fraying of the S.S. braiding that could occur from vibration under heavy stresses of the track. The heat shield wrapped around the OEM clutch line is to protect the sub-standard material from the heat damage of close proximity of the manifolds. It can't hurt to reinstall the OEM shielding.. it will help protect the line from heat and any roadway debris that might be kicked up off the front tires.

Great write up - just what I was looking for. I'm planning to upgrade my 40th.

Thanks

06-20-2011, 07:21 PM	#1 (permalink)
SPOHN A True Z Fanatic Join Date: Feb 2010 Location: Covington, GA Age: 45 Posts: 14,844 Drives: Waiting on next Z Rep Power: 221	DIY: Stainless Steel Clutch Line Well after some time I decided to change out my puny stock clutch line to a more efficient stainless steel line from Z1 Motorsports. There pretty cheap part. I think $29 bucks. Plus you need to pick up a bottle Motul RBF600 brake fluild to help the system operate to it's fullest. This mod is best to do if your changing out your Catalytic Converter (Cats) to HFC's or TP's. For they will need to be removed to to this install. I couldn't imagine them being done with them on the car. If you never have removed your Cats I suggest doing some good research first. They could be a pain. But I have been moved. Wasn't a big deal for me, but others have struggled. 14mm socket Rachet Extension (12'' preferable) Swivel 14mm wrench (2 works best) 10mm line wrench (standered wrench can work) 10mm socket 8mm wrench Flathead screwdriver Pliers Here in the first pic you'll see the cross member brace that connects to my Test Pipes (TP). They actual connect to both sides of my TP's or Cats, whatever you might have. Plus there's two bolts that help hold the bracket in place to the underside of the transmission. There's four in all. All are 14mm. Use your rachet and socket with your wrench together to remove all. Place to the side. You'll also need to go ahead and unplug the O2 sensor for the driver side. You can see in the pic the passenger side is still hooked up. It can be left alone. My next two pics you can get a good picture of my TP's. You will need to remove the two 14mm nuts and bolts on the flange in the far left of the first pic using two 14mm wrenches works best for me. And in the second you will see the triangle shaped flange that connects to the maniflold. You will have to remove the three nuts and bolts here also. This is where your rachet, socket, extension, and swivel works best. There are actually two nuts and bolts and the third is just a nut due to there a set bolt already placed in the manifold flange. You can see the different one in the top right of the flange. Now below are some pics of my TP's removed along with the clutch lines. Look carefull at them. You will noticed the hard line on the inner side of the body, then the rubber line in the middle (has heat shield on it), and then another hard line that connects to the transmission. Ok. In the pic below (same as above) start to remove this hard line. Start with the silver bracet and black bolt the lays in the middle of the the line. Remove it with a 10mm socket. Then start to remove the hard line form the clutch slave cylinder (the brass colored fitting) using a 10mm line wrench or standard wrench. Just be carefull here for these fittings are usally over tighten from the manufacture and can be strip easly. Even though you will not be reusing this particular line and fittings back for it will not be needed. The new line deletes this part. It has a banjo fiittng that bolts directly to the clutch slave cylinder. Also have a drip tray ready for just about all the fluid will leak out here. Also in the upper middle part of the pic you will see a pressure clip that will have to be pulled out using a flathead screw driver to pull out. The clip has a lip on that can be pried on. This clip can be tight. See the second pic for better look. The third pic is what you will end up with. Just let all the fluid drain out at this point. Mkae sure the cap is off the reservoir to allow for flow. Now were going to concentrate on the other end of the the clutch line. This can be tricky here. For it is a tight area to work in being the manifold flange is all in the way. These connection points also have a pressure plate here also. I found it easier to remove the pressure plate first with a flathead. And pull down on the line a litte but not to hard. Don't want to hurt anything. Normally I'd say leave the line in place untill you loosen the line. But there is hardly any room to turn a line wrench in there due to the manifold flange. And being likely over tighten from the manifacture you could easily strip it. I know for I did. I had to order another hard line. It was only $13. But doing it the way I'm describing and some patience you should be fine. Back to removing. Refer to the second pic. Sorry it's blury. You will see the line pulled down a little. Use some pliers and grip the bigger part of the fitting just above the heat shield. It has two flat edges to grip. Careful of the heat shield for you will reuse it on the new line. Then use a 10mm wrench on the upper nut and losen. Remove line and then remove heat shield by cutting zip ties. The Z1 kit comes with new zip ties. Now take the new SS clutch line. Comes with a line, banjo bolt (what I call it), two copper washers, and zip ties. Now take the bigger part of the new line and attach it to the the hard line by the manifold flange. It only needs to be tighten to about 12lbs of torque. I just use my best judgement here. Good thing the Z1 line has a hex fitting (19mm) that makes it easier to connect to the hardline. Just reconnect same way you undid. Route the fittings back up into the shelf stub where you pulled the pressure plate from and reinstall it. This can be hard for you have to hold the line even as you press in the clip. I had to hold the line take a flathead screwdriver and pry between the clip and the manifold flage. Be carfull not to slip. Could bust your knuckles. Now slip the heat shield over the new line. Take the other end of the line (the banjo fitting), banjo bolt, and copper washers ( 2 of them). Use the copper washers on both sides of the banjo fitting and tighten to the clutch slave cylinder (brass fitting). Might have to route the line around to the inside the bleeder screw then tighten. You can see below. Also go ahead zip tie the heat shied tighter to the new line and cut off excess. Mkae sure everything is tight. Reinstall TP's. Now start to bleed the clutch. Fill the clutch resesvoir with the Motul brake fluid. It's the small cap to the right in the first pic below. Fill up to top. Put cap on. Start pumping clutch alot. You will have to use your hand at first. For once depressed it wont come back up. You also in the begining have to open the bleeder screw to get the fluid to flow down at first. This is where the 8mm wrench comes in. Seal off bleeder screw, pump clutch with hands more. It will take a bit. Keep going back to reservoir to always make sure it doesnt get to low and feel up with air and that your always reinstalling the cap. I feel this is easier than doing the brakes. A lot less fluid and lines. Just keep bleeding till all the old fluid is out and your sure the new fluid is coming threw. Now eventually you will feel the pressure build for it will be alot stiffer than stock. Even though the pressure will build and the clutch will rebound on it's own when you open the bleeder screw the clutch will stick to the floor and you will have to seal off the screw and pull the clutch back up last time. Ensuring the bleeder screw is sealed off pump the clutch some more and pressure will build. Top off the fluid one more last time. Sorry for no pics on this. But I do hope this helps alot. Again I hope this helps and you guys like my write up. Sorry for any bad grammer. Now enjoy your stiffer feel clutch line. It's a big difference from stock. Combined with the fluid you should have to worry about the clutch sticking to the floor from hard launches and track days. Any suggestions or questions and comments welcome. Write ups are usally big and easy to leave out some things for it's alot to do. JIN2012 likes this. __________________ Last edited by SPOHN; 01-27-2012 at 08:25 PM.

06-21-2011, 02:08 PM	#2 (permalink)
wheee! A True Z Fanatic Join Date: Sep 2009 Location: Mod Capital of Canada Age: 57 Posts: 7,354 Drives: cars. lots of cars. Rep Power: 40182	Is it absolutely necessary to remove the TP's or Cats? __________________ H&R / Stillen / Berk / HKS / Swift / Michelin / UpRev / SPC / Amuse Rep / Seibon / Fringe XVO / TWM / more... My Journal

06-21-2011, 04:13 PM	#6 (permalink)
SPOHN A True Z Fanatic Join Date: Feb 2010 Location: Covington, GA Age: 45 Posts: 14,844 Drives: Waiting on next Z Rep Power: 221	Oh yea. Damn! I got yea. I wouldn't of found it without you. __________________ Last edited by SPOHN; 06-21-2011 at 04:19 PM.

07-03-2011, 11:01 AM	#7 (permalink)
SPOHN A True Z Fanatic Join Date: Feb 2010 Location: Covington, GA Age: 45 Posts: 14,844 Drives: Waiting on next Z Rep Power: 221	Week later update. The clutch pedal feels alot better than ever. Great soild feel. Almost gives you confindence. Now if I could just get my softer clutch spring I'll be set. __________________

02-10-2012, 01:15 PM	#9 (permalink)
modme Enthusiast Member Join Date: Mar 2009 Location: NY Posts: 345 Drives: G37 Rep Power: 16	Less than 1. The clutch reservoir is tiny. Even with flushing, it shouldnt take more than 1 bottle. __________________ GTM Twin Turbo Stage 2\|GTR Turbo/Engine Gauges\|KW V3 Coilovers\|HKS Exhaust\|Oil Cooler\| Vossen CV1

06-21-2011, 02:50 PM	#3 (permalink)
daisuke149 My *** is famous! Join Date: Mar 2010 Location: Alpharetta, GA Posts: 4,849 Drives: 2013 Boss 302 PW Rep Power: 31	good write up Chris. The TP / HFC doesnt have to be removed. When mine was put it, we did not remove them. Just gotta be able to reach slightly behind them.

06-21-2011, 04:11 PM	#5 (permalink)
daisuke149 My *** is famous! Join Date: Mar 2010 Location: Alpharetta, GA Posts: 4,849 Drives: 2013 Boss 302 PW Rep Power: 31	you mean wheres my rep for giving you directions!!

02-10-2012, 12:34 PM	#8 (permalink)
rambunctious Base Member Join Date: Feb 2011 Location: in the cowboys stadium Posts: 183 Drives: your mom crazy.. Rep Power: 14	How many bottles of brake fluid are needed for this line change?

02-10-2012, 01:15 PM	#10 (permalink)
modme Enthusiast Member Join Date: Mar 2009 Location: NY Posts: 345 Drives: G37 Rep Power: 16	It looks like you have a gasket leak on your test pipes. Might want to put some RTV over the gaskets. __________________ GTM Twin Turbo Stage 2\|GTR Turbo/Engine Gauges\|KW V3 Coilovers\|HKS Exhaust\|Oil Cooler\| Vossen CV1

07-09-2012, 09:22 AM	#11 (permalink)
370Z Purist A True Z Fanatic Join Date: Jun 2009 Location: Zion, Illinois Posts: 1,873 Drives: '09 370Z-T BS M6 Rep Power: 19	Why isn't this stickied?! This should DEFINITELY be stickied. __________________ -Phil "Since one of my brake light bulbs just went out, the forum told me that my piston rings are about to blow."

01-14-2013, 09:31 PM	#12 (permalink)
scruffydog A True Z Fanatic Join Date: Jan 2009 Location: Nor Cal Posts: 1,113 Drives: with his eyes close Rep Power: 717	Heat shield I recently ordered an Insulated S.S. from the Z Store. Link Do you think I should do a heat shield over it anyway even though it's insulated? I would think it wouldn't hurt to put a heat shield on anyway, where did you get your heat shield from? Cheers! __________________ Magnetic Black 2010 370z Scruffydog's Journal

01-14-2013, 09:37 PM	#13 (permalink)
SPOHN A True Z Fanatic Join Date: Feb 2010 Location: Covington, GA Age: 45 Posts: 14,844 Drives: Waiting on next Z Rep Power: 221	I just reused the stock one. You can get a clutch line from Z1 for $29. Z1 370z/G37 Stainless Steel Clutch Line __________________

01-14-2013, 10:25 PM	#14 (permalink)
scruffydog A True Z Fanatic Join Date: Jan 2009 Location: Nor Cal Posts: 1,113 Drives: with his eyes close Rep Power: 717	oh i had no idea the stock one already has a heat shield on it. In that case I'll just use the stock one over the insulated s.s. clutch line i got from the Z store. Thanks! __________________ Magnetic Black 2010 370z Scruffydog's Journal

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
DIY: Challenge Stainless Steel Brake Lines	M.Bonanni	DIY Section (Do-It-Yourself)	74	03-02-2019 10:25 PM
[FOR SALE] BRAND NEW Z1 stainless steel clutch line	98intrigue	Parts for sale (Private Classifieds)	2	05-13-2011 03:23 PM
It's Not Stainless Steel!	vipor	Other Vehicles	16	03-18-2010 10:43 AM
Stainless Steel Lines, which brand to get	SOLISIMO	Brakes & Suspension	15	12-18-2009 12:13 PM
GT Motorsports: Stainless Steel Braided Clutch Line	George@GTM	Suspension/Brakes	3	02-17-2009 05:56 PM