I would be surprised if he used a torque wrench or an air ratchet on the header bolts. That would be a pretty magical feat. There's a few on the
|
|
LinkBack | Thread Tools | Display Modes |
05-10-2009, 06:30 PM | #16 (permalink) |
A True Z Fanatic
Join Date: Mar 2009
Location: Houston, TX
Posts: 4,024
Drives: too slow
Rep Power: 3594 |
I would be surprised if he used a torque wrench or an air ratchet on the header bolts. That would be a pretty magical feat. There's a few on the top that are pretty easy to reach, but the bottom rear two on both sides are a huge pita to even get a regular combination wrench onto.
The worst one on the whole thing is the center bottom bolt on the driver's side. You really want a good 14mm gearwrench sort of thing for that. You'll just barely be able to get it in there, and barely be able to reach it with your fingertips, and then you get to tighten it 1 click at a time. Oh yeah, and then you have to try to torque that bolt down hard somehow, with only a few fingers able to reach the barely-moving wrench. We (I had a couple friends helping) probably spent over an hour just on tightening that one damn bolt (we didn't have a gearwrench, so we used a plain 12-pt box-end wrench. Turn it one 'point', and then readjust again.... ) |
05-10-2009, 06:45 PM | #17 (permalink) |
A True Z Fanatic
Join Date: Jan 2009
Location: Behind enemy lines
Age: 54
Posts: 5,995
Drives: People to drink
Rep Power: 32 |
No, I know he used an air ratchet. I was standing there watching him. The only thing I'm unsure of is whether or not he used a torque wrench afterwards to verify the torque. But I'm 100% positive he used an air ratchet, because he kept looping the hose over his neck and shoulders. I asked him why he was doing that and he said it was to avoid the hose touching my car and potentially scratching the finish. Pretty conscientious guy, huh? He has a ton of funky looking adapters for tight spots too. I'm guessing those helped. He did bitch about that center bottom bolt, but he didn't have as bad a time with it as you did. All he said about it was to make sure I tell people that they need to be able to work by feel, because there's no way to see it.
__________________
"There are no small accidents on this circuit." -- Ayrton Senna 316.8whp & 248 ft/lbs (Dyno Dynamics) | 319whp & 256 ft/lbs (DynoJet) (04/23/10) Stillen G3 CAI, CBE, Pulley / F.I. LTH / GTSpec Ladder Brace / Setrab Oil Cooler / UpRev-tuned by Forged Perf. Last edited by semtex; 05-10-2009 at 06:47 PM. |
09-16-2009, 02:02 PM | #20 (permalink) |
A True Z Fanatic
Join Date: Jan 2009
Location: Behind enemy lines
Age: 54
Posts: 5,995
Drives: People to drink
Rep Power: 32 |
Yes.
__________________
"There are no small accidents on this circuit." -- Ayrton Senna 316.8whp & 248 ft/lbs (Dyno Dynamics) | 319whp & 256 ft/lbs (DynoJet) (04/23/10) Stillen G3 CAI, CBE, Pulley / F.I. LTH / GTSpec Ladder Brace / Setrab Oil Cooler / UpRev-tuned by Forged Perf. |
09-16-2009, 05:33 PM | #22 (permalink) |
A True Z Fanatic
Join Date: Jan 2009
Location: Behind enemy lines
Age: 54
Posts: 5,995
Drives: People to drink
Rep Power: 32 |
Nope, everything's been fine. No issues. No heat issues either. The headers are ceramic coated, and then wrapped in addition to that, so I think things are good on that front.
__________________
"There are no small accidents on this circuit." -- Ayrton Senna 316.8whp & 248 ft/lbs (Dyno Dynamics) | 319whp & 256 ft/lbs (DynoJet) (04/23/10) Stillen G3 CAI, CBE, Pulley / F.I. LTH / GTSpec Ladder Brace / Setrab Oil Cooler / UpRev-tuned by Forged Perf. |
11-05-2009, 12:59 PM | #23 (permalink) |
Enthusiast Member
Join Date: Jun 2009
Location: Canton, GA
Posts: 465
Drives: 2013 Shelby GT500
Rep Power: 428 |
Hey Semtex, who did your header installation? I want to get the Stillen headers and are looking for a repurable installed that has experience installing the headers on a 370z. Thanks for the step-by-step pictures and explanation of the installation process and challenges!
Thanks!
__________________
|
11-05-2009, 01:07 PM | #24 (permalink) |
A True Z Fanatic
Join Date: Jan 2009
Location: Behind enemy lines
Age: 54
Posts: 5,995
Drives: People to drink
Rep Power: 32 |
You sure you want the headers? They're a complete waste of money, IMO. PM me your contact info if you really want them and I'll fwd to my guy.
__________________
"There are no small accidents on this circuit." -- Ayrton Senna 316.8whp & 248 ft/lbs (Dyno Dynamics) | 319whp & 256 ft/lbs (DynoJet) (04/23/10) Stillen G3 CAI, CBE, Pulley / F.I. LTH / GTSpec Ladder Brace / Setrab Oil Cooler / UpRev-tuned by Forged Perf. |
11-05-2009, 02:17 PM | #26 (permalink) |
A True Z Fanatic
Join Date: Jan 2009
Location: Behind enemy lines
Age: 54
Posts: 5,995
Drives: People to drink
Rep Power: 32 |
Go to this thread and judge for yourself -> Stillen Headers installed - Review/Pics/Vid/Dyno
__________________
"There are no small accidents on this circuit." -- Ayrton Senna 316.8whp & 248 ft/lbs (Dyno Dynamics) | 319whp & 256 ft/lbs (DynoJet) (04/23/10) Stillen G3 CAI, CBE, Pulley / F.I. LTH / GTSpec Ladder Brace / Setrab Oil Cooler / UpRev-tuned by Forged Perf. |
11-05-2009, 03:24 PM | #27 (permalink) | |
Enthusiast Member
Join Date: Jun 2009
Location: Canton, GA
Posts: 465
Drives: 2013 Shelby GT500
Rep Power: 428 |
Quote:
__________________
|
|
04-19-2010, 06:11 PM | #29 (permalink) |
Base Member
Join Date: Mar 2010
Location: chicago
Posts: 5
Drives: G37xS
Rep Power: 15 |
i'm just wondering why it's so hard to make a set of headers that have perfect fitment? i mean, really, how hard can it be to make them so that they line up with the factory exhaust???
|
07-26-2010, 11:52 AM | #30 (permalink) |
Track Member
Join Date: Jul 2010
Location: New York, Long Island
Posts: 559
Drives: PW Base Sport 6 Spd
Rep Power: 16 |
^^ i also have the saem question nothing aftermarket seems to ever fit right. there is stuff out there that works but more times then not it doesnt work
this doesnt look that bad to do. i did headers on my 95 firebird. you want to talk about a pita? it took me about 3-4 hours to get ONE side in. and that was the easy side. and i also went to school and worked at two dealers and still had problems. if you decide to tackle something like this def have someone that knows what they are doing right next to you and make sure you have all the right tools to do so. |
Bookmarks |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Stillen Gen3 Intake, Berk Hi-flow cat, and Stillen cat-back exhaust | axio | Intake/Exhaust | 82 | 07-31-2009 01:41 PM |
STILLEN Sweepstakes - Free Trip To See The STILLEN GT-R Rally! | Josh@STILLEN | Nissan 370Z General Discussions | 36 | 06-30-2009 01:44 PM |
Muffler shop ? and header questions.. | AceSpade77 | Intake/Exhaust | 3 | 05-06-2009 12:35 PM |
Installation of Bluetooth. . . | keke | Nissan 370Z General Discussions | 10 | 05-05-2009 09:38 PM |
Header-Downpipe gasket & Stillen CBE Allignment | DannyGT | Intake/Exhaust | 21 | 04-24-2009 12:35 PM |