DIY-Door handle removal

bumblez · 01-16-2011, 02:22 PM

I know there's already has DIY by 209Z DIY Removal of Door Handles , but had no pics of installation. So here it is

Tools Required:
Rachet&10mm socket
Flat head screw driver(for

Driver's
1. Locate& remove 2 rubber grommets.

2.unbolt the 3, 10mm bolts. 1on top hole and 2 on bottom hole.
*Be careful Screw can fall inside the door. I used magnetic screw driver*

3.pull up & out on the door handles.

4.You will see two wires. One for the Keyless entry(black wire) and other wire to physically open the door(Metal wire). Pop out 2 clips that holding the black wire and disconnect. And pop out the metal wire.

5. Driver's side done. Take 5 min brake

Passenger's

The only difference between Driver's and Passenger's is number of bolts.
Driver's has 3 10mm bolts and Passenger's has 2 10mm bolts. Other then its almost same.

All Finish!! Do whateva u want!! (Paint or Replace with others)
I swapped mine with Simot1's CF door handles. Thanks Simot!!

+Rep Me if I helped.

209Z · 01-16-2011, 09:50 PM

yay. Thanks for updating with pics! =]
+ rep homie!

Trips · 01-16-2011, 10:01 PM

Nice write up

I might add that once you detach the Driver side handle? That both windows will automatically roll down as a safety precaution, And will have to be reset once reinstalled.

Xan · 01-16-2011, 10:12 PM

Quote:

Originally Posted by Triple's

Nice write up

I might add that once you detach the Driver side handle? That both windows will automatically roll down as a safety precaution, And will have to be reset once reinstalled.

In that case, might as well at the reset procedure to this thread:

1. Turn the ignition from OFF to ON, you don't have to start the car for this. Just press the start button until it gets to the ON state, usually OFF > ACC > ON.
2. The airbag light should turn on, wait until it turns off (it should stay on for 7 secs and then turn off) and then turn the ignition to OFF within 1 second.
3. Wait more than 3 seconds after the ignition turns OFF.
4. Repeat steps 1 to 3, twice. (Total 3 times)

209Z · 01-16-2011, 10:28 PM

BAM TEAM WORK WOOOT!!!! haha (NOS energy drink)

Trips · 01-16-2011, 10:33 PM

Quote:

Originally Posted by Xan

In that case, might as well at the reset procedure to this thread:

1. Turn the ignition from OFF to ON, you don't have to start the car for this. Just press the start button until it gets to the ON state, usually OFF > ACC > ON.
2. The airbag light should turn on, wait until it turns off (it should stay on for 7 secs and then turn off) and then turn the ignition to OFF within 1 second.
3. Wait more than 3 seconds after the ignition turns OFF.
4. Repeat steps 1 to 3, twice. (Total 3 times)

TROOPER · 01-17-2011, 09:16 AM

AWESOME... Been waiting for a DIY with pics.

Got a spare set of handles here already painted and waiting for install

shadoquad · 01-17-2011, 10:34 AM

Quote:

Originally Posted by TROOPER

AWESOME... Been waiting for a DIY with pics.

Got a spare set of handles here already painted and waiting for install

Oh, man, if you do this, you'd better come out so we's can see it in MD!

TROOPER · 01-17-2011, 01:48 PM

Quote:

Originally Posted by shadoquad

Oh, man, if you do this, you'd better come out so we's can see it in MD!

I just need some warm weather LOL.

docaam · 01-23-2011, 12:34 AM

looks nice man

bumblez · 01-23-2011, 05:01 AM

Quote:

Originally Posted by docaam

looks nice man

Thanks docaam

Paul_S · 01-23-2011, 05:40 AM

Thanks for that. I might be doing something with mine soon and that'll really help

Osiris · 02-22-2011, 05:15 PM

Quote:

Originally Posted by bumblez

2.unbolt the 3, 10mm bolts. 1on top hole and 2 on bottom hole.

Can you clarify this....are you saying once i remove the cover from the second hole that there's going to be 2 10mm bolts in there?

tomnavone · 03-01-2011, 10:10 AM

Thanks

TROOPER · 03-05-2011, 03:27 PM

Quote:

Originally Posted by shadoquad

Oh, man, if you do this, you'd better come out so we's can see it in MD!

Done..YAY..!!

Thanks to "Bumblez" for doing pics for this DIY

01-16-2011, 02:22 PM	#1 (permalink)
bumblez Enthusiast Member Join Date: Sep 2009 Location: VA Posts: 326 Drives: Amuse 370z Rep Power: 16	DIY-Door handle removal I know there's already has DIY by 209Z DIY Removal of Door Handles , but had no pics of installation. So here it is Tools Required: Rachet&10mm socket Flat head screw driver(for Driver's 1. Locate& remove 2 rubber grommets. 2.unbolt the 3, 10mm bolts. 1on top hole and 2 on bottom hole. Be careful Screw can fall inside the door. I used magnetic screw driver 3.pull up & out on the door handles. 4.You will see two wires. One for the Keyless entry(black wire) and other wire to physically open the door(Metal wire). Pop out 2 clips that holding the black wire and disconnect. And pop out the metal wire. 5. Driver's side done. Take 5 min brake Passenger's The only difference between Driver's and Passenger's is number of bolts. Driver's has 3 10mm bolts and Passenger's has 2 10mm bolts. Other then its almost same. All Finish!! Do whateva u want!! (Paint or Replace with others) I swapped mine with Simot1's CF door handles. Thanks Simot!! +Rep Me if I helped. danegrey and RayMaN like this.

01-16-2011, 09:50 PM	#2 (permalink)
209Z A True Z Fanatic Join Date: Mar 2009 Location: Stockton, Cali (209) Posts: 1,058 Drives: 09 370z Rep Power: 278	yay. Thanks for updating with pics! =] + rep homie! __________________ Team Blur My Build Thread Fast Intentions\|KWS\|BERK\|Carbon Fiber Element\| SEIBON\|Memphis Car Audio\| Status Autoworks\|Lusso Forged\|Autohaus\|PWJDM\|SPC

01-16-2011, 10:01 PM	#3 (permalink)
Trips Administrator Join Date: May 2009 Location: Disneyland, Ca Posts: 8,732 Drives: 🔰 Rep Power: 10	Nice write up I might add that once you detach the Driver side handle? That both windows will automatically roll down as a safety precaution, And will have to be reset once reinstalled. __________________

01-16-2011, 10:28 PM	#5 (permalink)
209Z A True Z Fanatic Join Date: Mar 2009 Location: Stockton, Cali (209) Posts: 1,058 Drives: 09 370z Rep Power: 278	BAM TEAM WORK WOOOT!!!! haha (NOS energy drink) __________________ Team Blur My Build Thread Fast Intentions\|KWS\|BERK\|Carbon Fiber Element\| SEIBON\|Memphis Car Audio\| Status Autoworks\|Lusso Forged\|Autohaus\|PWJDM\|SPC

01-17-2011, 09:16 AM	#7 (permalink)
TROOPER A True Z Fanatic Join Date: Jun 2010 Location: Baltimore, MD Posts: 1,297 Drives: Your Tax Dollars Rep Power: 17	AWESOME... Been waiting for a DIY with pics. Got a spare set of handles here already painted and waiting for install __________________ Darren "Guv Motors Passion Wagon"

01-23-2011, 12:34 AM	#10 (permalink)
docaam A True Z Fanatic Join Date: Nov 2009 Location: Dubai Posts: 2,532 Drives: Z34/240z/Hakosuka Rep Power: 29	looks nice man

01-23-2011, 05:40 AM	#12 (permalink)
Paul_S Enthusiast Member Join Date: Sep 2009 Location: England Posts: 258 Drives: UK Yellow 370Z Rep Power: 16	Thanks for that. I might be doing something with mine soon and that'll really help __________________ In the UK? Check out nissansportz.com - 350Z, GT-R, 370Z and more... 2004 Sunset 350Z to 2009 Limited Edition Ultimate Yellow 370Z

03-01-2011, 10:10 AM	#14 (permalink)
tomnavone Track Member Join Date: Apr 2009 Location: S.F. Bay Area Posts: 723 Drives: Supercharged 370z Rep Power: 17	Thanks __________________ GTM Supercharger/HKS Camp2/Berk cbe/Motordyne art pipes/Hotchkis sways/ Eibach Springs/ Black Volk TE37/Bridgestone S-04 Powered by

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
DIY: Door Panel Removal & Door Speaker Size	jikhead	DIY Section (Do-It-Yourself)	46	07-16-2016 11:04 PM
Door handle rattles from outside...anyone?	zaust	Exterior & Interior	1	02-27-2012 04:21 PM
370z door handle swap?	ThoriumHotdog	Exterior & Interior	11	11-03-2010 11:44 PM
EVO-R door handle review by SIMOTA1	simota1	Exterior & Interior	12	09-09-2010 10:56 PM
tried to remove door handle...Fail	Soon	DIY Section (Do-It-Yourself)	4	08-02-2010 05:03 PM