DIY-Door handle removal

Ill · 04-07-2012, 01:09 PM

Awesome then. I was worried it would rattle and be super annoying. I'll just buy new bolts and call it good. Even if it does rattle, my Stillen G3 and Ark exhaust arrive in a few days. Doubt I'll even notice it.

MVPTonyD · 04-09-2012, 07:15 AM

you think i can just spray paint these door handles with out sanding it? or will it look cheap.

kent370 · 04-09-2012, 03:54 PM

A quick addition to the DYI regarding the difficult-to-access 3rd internal bolt on the drivers door handle: don't try to remove it right away. First remove the two easy bolts, and the torx screw in the door jamb, and THEN the handle can then be pulled out and repositioned a little so that you can now get a straight shot at the 3rd internal bolt through the lower access hole, and this will make accessing that bolt much MUCH easier -- no need for flex handles, u-joints or other contortions.

Cheers,
Kent

Vichtz · 05-26-2012, 09:15 PM

Don't mean to thread necro but I did this today. Painting the handles while attached to the car is also a simple and viable option. First slide note cards under handles and tape them off. Next, wrap about 3 feet around in magazine or newspaper. then put a rudimentary "blast shield" on just to catch any paint blown by the wind. Easy as cake.

xweaponx · 06-06-2012, 07:07 PM

what'd you paint it with though?

LukasC · 06-16-2012, 01:09 PM

Problem!! Cant get the blue clip off that is for the button to unlock it. My hand barrely fits back there and i dont have a grip to pull it off. Is it clipped in there with tabs or i just pull hard on it?

urdeliveryguy · 09-15-2012, 02:37 AM

i took apart the back of my handles abit b4 i painted them. mainly the black plastic gasket and to take the button off. ill give warning to anyone... everyone of those lil screws contain a hefty amount of locktite.

of the 6 screws that i took off... 4 of them got completly stripped, one of them i couldn't even get off.. i ended up twisting the plate that holds the button down off and ripping the screw out (apoxy was need'd to fix it back in). went to the home depot and bought new screws. there metric size m4 machine screws for anyone who has done something similar and needs them replaced.

markthomas69 · 10-04-2012, 11:11 PM

I just picked up my 370 yesterday and I like the look of the black door handles. Even CF has a nice look to it.

Nut_N_Much · 10-05-2012, 11:26 AM

Quote:

Originally Posted by Vichtz

Don't mean to thread necro but I did this today. Painting the handles while attached to the car is also a simple and viable option. First slide note cards under handles and tape them off. Next, wrap about 3 feet around in magazine or newspaper. then put a rudimentary "blast shield" on just to catch any paint blown by the wind. Easy as cake.

Thats awesome bro. good job.. What type of paint are you using on your handles?

Coon-azz · 10-05-2012, 11:33 AM

I like the CF door handles. So, where can I get a set?

pfdaxe · 10-05-2012, 12:43 PM

Quote:

Originally Posted by Coon-azz

I like the CF door handles. So, where can I get a set?

Here ya go:

EVO-R INC. Nissan 370Z Z34 Carbon Fiber Exterior Door Handle Covers

Vichtz · 10-10-2012, 04:39 PM

Sorry I kind of forgot about this thread haha but to answer your question it was simple krylon. I did a once over with a self etching primer then about 3 coats of black gloss and probably 4 clear coats. Still looks great and in the name of science I went through a power touchless car wash. No issue withstanding the high pressure.

Grindkiezer · 10-10-2012, 08:29 PM

When it says to "pop out the two clips holding the black wire" do you mean take out the two small screws that are on the actual handle? one of those screws on my handles are stripped so there really isn't any way that I can take them out.

Someone please help me, I have an appointment to get these painted on Friday but I can't seem to disconnect the black wire.

I found the two clips on the inside of the door frame, but no matter how hard I pull on them the first clip won't come free. How do I get it loose?

Nut_N_Much · 10-13-2012, 11:02 AM

Quote:

Originally Posted by Vichtz

Sorry I kind of forgot about this thread haha but to answer your question it was simple krylon. I did a once over with a self etching primer then about 3 coats of black gloss and probably 4 clear coats. Still looks great and in the name of science I went through a power touchless car wash. No issue withstanding the high pressure.

Thank brother, I'm gonna try it..

Vichtz · 10-14-2012, 02:15 PM

Nice

good luck! post results!

04-09-2012, 07:15 AM	#47 (permalink)
MVPTonyD Base Member Join Date: Jan 2011 Location: Oklahoma Posts: 78 Drives: a scooter. Rep Power: 14	you think i can just spray paint these door handles with out sanding it? or will it look cheap. __________________ Salute

04-09-2012, 03:54 PM	#48 (permalink)
kent370 Base Member Join Date: May 2011 Location: Las Vegas Posts: 55 Drives: Camaro SS Rep Power: 14	A quick addition to the DYI regarding the difficult-to-access 3rd internal bolt on the drivers door handle: don't try to remove it right away. First remove the two easy bolts, and the torx screw in the door jamb, and THEN the handle can then be pulled out and repositioned a little so that you can now get a straight shot at the 3rd internal bolt through the lower access hole, and this will make accessing that bolt much MUCH easier -- no need for flex handles, u-joints or other contortions. Cheers, Kent BeemaaZ and RayMaN like this.

09-15-2012, 02:37 AM	#52 (permalink)
urdeliveryguy Enthusiast Member Join Date: Aug 2011 Location: philadelphia / delco Posts: 278 Drives: 09' touring 6sp Rep Power: 14	i took apart the back of my handles abit b4 i painted them. mainly the black plastic gasket and to take the button off. ill give warning to anyone... everyone of those lil screws contain a hefty amount of locktite. of the 6 screws that i took off... 4 of them got completly stripped, one of them i couldn't even get off.. i ended up twisting the plate that holds the button down off and ripping the screw out (apoxy was need'd to fix it back in). went to the home depot and bought new screws. there metric size m4 machine screws for anyone who has done something similar and needs them replaced. Last edited by urdeliveryguy; 10-04-2012 at 11:38 PM.

10-04-2012, 11:11 PM	#53 (permalink)
markthomas69 Base Member Join Date: Oct 2012 Location: Little Elm, TX Posts: 66 Drives: 2010 370Z Red, auto Rep Power: 13	What is the best paint for the door handles? I just picked up my 370 yesterday and I like the look of the black door handles. Even CF has a nice look to it.

10-05-2012, 11:33 AM	#55 (permalink)
Coon-azz Track Member Join Date: Mar 2012 Location: Fredericksburg,VA Posts: 689 Drives: '12 370z Sport DD Rep Power: 14	I like the CF door handles. So, where can I get a set? __________________ I don't care how slow you want to drive; I encourage it. JUST GET THE HELL OUT OF THE PASSING LANE YOU TUCK FARD!!!

04-07-2012, 01:09 PM	#46 (permalink)
Ill Base Member Join Date: Mar 2012 Location: Bellevue Posts: 177 Drives: 09 370z Base 6MT Rep Power: 13	Awesome then. I was worried it would rattle and be super annoying. I'll just buy new bolts and call it good. Even if it does rattle, my Stillen G3 and Ark exhaust arrive in a few days. Doubt I'll even notice it.

06-06-2012, 07:07 PM	#50 (permalink)
xweaponx Base Member Join Date: Sep 2011 Location: North Carolina Age: 33 Posts: 100 Drives: 2011 370Z Rep Power: 14	what'd you paint it with though?

06-16-2012, 01:09 PM	#51 (permalink)
LukasC Track Member Join Date: Apr 2011 Location: San Antonio, Tx Posts: 664 Drives: 11 Stillen SC Bl M6 Rep Power: 17	Problem!! Cant get the blue clip off that is for the button to unlock it. My hand barrely fits back there and i dont have a grip to pull it off. Is it clipped in there with tabs or i just pull hard on it?

10-10-2012, 04:39 PM	#57 (permalink)
Vichtz Track Member Join Date: May 2012 Location: Unknown Posts: 538 Drives: PG 09 Nissan 370z Rep Power: 14	Sorry I kind of forgot about this thread haha but to answer your question it was simple krylon. I did a once over with a self etching primer then about 3 coats of black gloss and probably 4 clear coats. Still looks great and in the name of science I went through a power touchless car wash. No issue withstanding the high pressure. RayMaN likes this. __________________ очень быстро ... Stillen Gen 3 CAI// Stillen CBE// B&M SS with PWJDM Shift Knob// Custom OCC// Drilled/Slotted Rotors//Halo/painted Headlights// Under-hood dress up

10-10-2012, 08:29 PM	#58 (permalink)
Grindkiezer Track Member Join Date: Sep 2012 Location: San Diego Posts: 824 Drives: A Car Rep Power: 14	When it says to "pop out the two clips holding the black wire" do you mean take out the two small screws that are on the actual handle? one of those screws on my handles are stripped so there really isn't any way that I can take them out. Someone please help me, I have an appointment to get these painted on Friday but I can't seem to disconnect the black wire. I found the two clips on the inside of the door frame, but no matter how hard I pull on them the first clip won't come free. How do I get it loose? __________________ Z Last edited by Grindkiezer; 10-10-2012 at 08:50 PM.

10-14-2012, 02:15 PM	#60 (permalink)
Vichtz Track Member Join Date: May 2012 Location: Unknown Posts: 538 Drives: PG 09 Nissan 370z Rep Power: 14	Nice good luck! post results! __________________ очень быстро ... Stillen Gen 3 CAI// Stillen CBE// B&M SS with PWJDM Shift Knob// Custom OCC// Drilled/Slotted Rotors//Halo/painted Headlights// Under-hood dress up

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
DIY: Door Panel Removal & Door Speaker Size	jikhead	DIY Section (Do-It-Yourself)	46	07-16-2016 11:04 PM
Door handle rattles from outside...anyone?	zaust	Exterior & Interior	1	02-27-2012 04:21 PM
370z door handle swap?	ThoriumHotdog	Exterior & Interior	11	11-03-2010 11:44 PM
EVO-R door handle review by SIMOTA1	simota1	Exterior & Interior	12	09-09-2010 10:56 PM
tried to remove door handle...Fail	Soon	DIY Section (Do-It-Yourself)	4	08-02-2010 05:03 PM