Nissan 370Z Forum  

Stebel Nautilus horn install

Like many here, I was disappointed with the wimpy horns on the 370 and longed for a way to wake up the oafs drifting into my lane. I liked the

Go Back   Nissan 370Z Forum > Nissan 370Z Tech Area > DIY Section (Do-It-Yourself)


Like Tree3Likes
  • 2 Post By JARblue
  • 1 Post By 6mileZ

 
 
LinkBack Thread Tools Display Modes
Prev Previous Post   Next Post Next
Old 05-15-2016, 08:47 PM   #1 (permalink)
Base Member
 
Join Date: Aug 2014
Location: South Carolina
Posts: 3
Drives: 11 Nissan 370Z xx M6
Rep Power: 11
6mileZ is on a distinguished road
Default Stebel Nautilus horn install

Like many here, I was disappointed with the wimpy horns on the 370 and longed for a way to wake up the oafs drifting into my lane. I liked the look of the Stebel Nautilus and decided to do the install. The bumper removal was a bit intimidating, but it went fine (remove bottom bolts, side bolts, top plastic doohickeys; install in reverse). The videos online helped, and I was pleased to learn that I could do it without jacking the car.

I apologize for not having pix, but I just wanted to pass along a few hints that really don't need a visual.

The horn comes with the required 30 amp relay. I also purchased the wiring kit, which was good for the required 30 amp inline fuse and better instructions than those that come with the horn. But the kit is likely sized for motorcycles because the length of wire is way too short. Plus, the enclosed female blade connectors did not work with the 14 gauge wire you need to connect from battery to relay to horn.

I bought new female blade connectors that worked with the 14 gauge wire, plus a 25 ft length of 18-2 wire to run from the horn back to the relay (the old horn used two wires, so you connect to these and run to the relay). I bought 25 ft of 14 gauge wire, too.

I installed the inline fuse and the relay inside the battery compartment. The fuse line connects to the + terminal and to the #87 blade on the relay. I ran 14 gauge wire from #30 blade on the relay to the + terminal on the horn. The 18-2 wire is used to run from the other two blades on the relay to the two wires that are removed from the old horn. I chose to keep the horn in the center and replace the horn that is forward of the left front wheelwell. The new horn fits easily into the hole of the old one.

One key is to make a good ground of the horn to the chassis. My first choice was close to the horn, but too weak, so the horn just sputtered. So I ran a new 14 ga line from the neg terminal of the horn to an obvious chassis ground on the wheelwell itself. Problem solved.

The result it impressive, much louder than the old horns but not like a train or semi. Hope this helps if you want to install a new horn.
- Jeff
6mileZ is offline   Reply With Quote
 

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Aftermarket navi Install.. Kenwood 5140.. No horn or beeps with locking!! LudeSH01 Audio & Video 7 03-31-2015 11:11 AM
Upgraded horn dP3NGU1N Nissan 370Z General Discussions 33 10-31-2014 02:31 PM
Lock it, but no horn? akgambler47 Audio & Video 18 11-17-2012 01:56 PM
Newbie - To horn or not to horn (Image Dynamics) SP33DKILLS Audio & Video 12 04-09-2012 02:34 PM
where is the fuse for the horn?! kgreen Nissan 370Z General Discussions 12 10-11-2010 11:16 PM


All times are GMT -5. The time now is 05:27 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO 3.6.0 PL2