DIY: Show-n-Go Front License Plate Install (Grill Location)

Boost_lee

First off, thanks to ENT-Z for his DIY Install Procedures on his unit. Instead of installing the unit on the bottom of the vehicle, this thread covers the option of mounting the unit in the grill area of the stock front bumper.


I found the unit at Yates Performance for $119.95 with free shipping.
2008-2010 Dodge Challenger Show-N-Go Retractable License Plate Frame

These kits are universal for the most part, so I just used the Dodge Challenger kit as it was one of the cheapest (for some reason, the Corvette kits cost more).

In addition to the kit I used the following tools:

• Flathead/Phillips screw drivers
• Self tapping screw
• Cordless drill
• Mini hack saw or sharp blade/box cutter
• 10mm socket/ratchet
• Double sided tape
• Black zip ties

-------------

First remove the plastic undertray. I used AK's DIY for the oil change. If you need the car higher, feel free to jack the vehicle up, or use ramps. I did this install with the car on the ground, but it would have been easier if the car was raised.

Installing in the grill area will require cutting of the black plastic in the center area of the grill. I had to cut 2 of the small vertical beams on the bumper, which is can barely be seen when looking at the car. I borrowed a pic from ENT-Z to show which beams were cut. (Beams are in the lightened boxes)



Just use your hack saw or equivalent to cut these pieces. I tried to cut them as flush as possible on the bottom.

Slide your show-n-go assembly in through the grill area. If you need a little more room to work with, you can always pop out the tow hook cover. I used some plastic ties for the front support of the bracket to the horizontal black grill piece. I mounted mine to the right of the tow hook access plate. This allows the tow hook to still be functional with the plate in the down/hidden position.



Since the black ties are used, there is hardly any noticeable evidence if the unit is removed from the car in the future (no screw holes etc). If you'd like to use screws or double sided tape feel free, but I felt that the zip ties offered a more reliable option with less hassle. (Note: If you need to slide the plate frame from the hidden to exposed position, you can do this manually with you hands, but be sure to slide the plate slowly)

Once the front of the assembly if secure to the horizontal grill beam, we need to mount the rear. For the rear support of the bracket, I made a Z-shaped bracket out of their supplied metal and drilled a small self tapping screw into the bottom of the aluminum bumper beam. I attached the bottom of the bracket to the assembly using the supplied hardware.



After this is secured, simply screw your license plate on with the supplied screws. Of course, you may need a few test fits to get everything just right. The clearance spaces are small, but there is enough to work with, trust me.

This is what the unit looks like in the hidden position.




All that is left is the wiring. Wiring is very simple for this kit and instructions are included. They can also be downloaded here. I mounted the control box in the battery compartment so it is hidden from view. I ran the wires behind the engine compartment side trim, and all the way down to the show-n-go assembly. The unit instructions say that you can get power straight from the battery since it uses an extremely low current draw. I used the neg terminal ground, and tapped power off of the alternator fuse (which is also located in the battery compartment).

The plate is very secure and works flawlessly. It is mounted in a recessed part of the grill, so it doesn't protrude out very much. Unless someone is carefully looking, they will not notice the plate and bracket in the hidden position. Plus, since it is mounted in the grill area, there no chance of bottoming out the front end and scraping your license plate

Here's a video of the operation, just click on the picture. (sorry for the low lighting, photobucket darkened it quite a bit)


Rep if you find this useful

PhoenixMr2

LOVE IT! This is just awesome. I will be doing this almost immediately after purchasing my Z

Boost_lee

Thanks, glad I could assist

Boost_lee

This clip might be a little easier to see

roplusbee

That is awesome.

__________________
2007 350Z NISMO #0618: Zerolift | UPREV | F.I. | Greddy | Competition Clutch | Injector Dynamics | Aeromotive | Pioneer | JL

Jeffblue

hey man, great install. I like the location of it since it sits where a plate should, height wise. Was it possible to put it in the center or no? If so i'd be down to do this as well. let me know.

+rep for posting this too.

Boost_lee

Thanks Jeff

As for the center location - it can be done. The only difference is that there is a metal beam in front of the radiator at the center of the car. This is the same beam that holds the Nismo body dampeners. Since this beam is there, the Show-n-Go assembly will sit .5-1 inch farther out of the bumper. Also, there is an ambient air temp sensor there that may/may not need to be located. It is certainly possible, but I didn't want to mess with this, especially with the bumper still attached.

On a side note, chances are that you are not going to have this plate in the displayed position very often. My plate is a little crooked, but I don't mind since its hardly displayed. If you do drive around a lot with the plate displayed, and only need it down for certain occasions, then I'd probably save a few bucks and get the non-motorized version.

Jeffblue

cool, thanks man

ENT-Z

Nice work!! I originally intended to mount it in the grill area but got discouraged by the beam. My preference was to keep it centered but mount it lower. I like your adaptation as well though! As far as bottoming out, no issues there. The plate assembly sits 1/2" higher than the bottom of the diffuser. I got pulled over one time so far and flipped it up after the pull-over. The cop seemed awful confused! I got an illegal tint ticket though so I still came out the loser

Boost_lee

ouch on the ticket!

Thanks for the input, I just didn't want to hack the chin spoiler at the time, as I love the way it looks.

tonybui

Does it still work after all this time? I might consider this option !!!


Sent from my iPhone using Tapatalk

__________________
Evo-R CF fang | CF Mirror covers | 20/25 H&R spacers | RE-11 | TopSpeed exhaust + y-pipe | Stillen HFC | Carbon Fiber Amuse rear bumper + Amuse Spoiler | PWJDM

Boost_lee

Still works and seems to be everyone's favorite mod at the meets

The only thing I'll add is that you need to remove the zip ties and replace every time you remove the bumper. I've done about three removals and it still works great

__________________
My TT Z

kenchan

lol! i jumped when the plate popped out of nowhere in the vid. hahahaha!

GJ!

Boost_lee

Lol thanks. I have fun with it at the meets. I stand about fifty feet from the car and pop the plate while people are just standing by the car. The reactions are great lol

__________________
My TT Z

rhd

Dude! That is awesome, reminds me of James Bond 007...