So whats up Doc?
 

So.... I'm new and all but...how does one replace/clean the filters on this set-up?:ughdance:

Remove the front bumper to clean filters

You're welcome :tup: . I am glad I could post it for you guys so that you can get useful information before tackling this install.

I am updating this info: I should mention here that for 2013 models, there are electrical wiring that's attached to front bumper. Please use extreme caution when you take it off. If anyone with 2013 Z takes off their front bumper, please send me some pics so that I can update it. (thank you xTETOVABOYx)

Post updated with pics
 

Here are some pictures of 2013+ front bumper led wiring: Huge thanks to xTETOVABOYx for providing me with the pics. Thank you

http://i576.photobucket.com/albums/s...ps890479e4.jpg
Passenger Side Connection On picture #1

http://i576.photobucket.com/albums/s...ps9e9caf71.jpg
Passenger Side LED picture #2

http://i576.photobucket.com/albums/s...ps1245fd85.jpg
LED on Driver Side , Shows how long wire is picture #3

http://i576.photobucket.com/albums/s...psbc9657dc.jpg
Actual led of the driver side picture #4

AK, great thread and pics. Makes installing this thing look possible to even the most amateur of enthusiasts :)

Few questions...

I've read elsewhere (links below) that following installation of this Stillen G3 system, a tune (preferably uprev) is essential as the air / fuel ratios are wayyy out of whack. Thoughts?

http://www.the370z.com/intake-exhaus...tml#post461753

Also, if you've added/adding an aftermarket CBE and/or HFCs (such as FI), the power benefits of this CAI are somewhat minimal if any...

http://www.the370z.com/intake-exhaus...tml#post461135

Perhaps drop-ins are the way to go for those who have aftermarket CBEs / HFCs??

i hope this helps most of you with the 2013 bumper ! , loving the Gen 3's :)))

Thanks man, that was my main concern if the Gen 3 fit the 13 model year. Cause not even in the stillen page is it updated for the 13 model. Quick question, do the wires for the LEDs unplug or do you have to take the whole LEDs apart from the bumper?

awesomeawesomeawesome i cant wait to get the stillen g3s now

Thanks AK, just installed them this weekend. Never would have tried it without your DIY.

they unplug, really simple

Refer to picture one. The plug is right under the reservoir on the passenger side, Refer to picture 3 for drivers side. the plug is right on the led as you can see it from a top view

Where did you get that filler foam stuff?

Got mine, this thing is amazing :happydance:

Here are two more photos of the LEDS to compliment xTETOVABOYx pics. Thanks for the DIY. :tiphat:

I noticed one post mentioned the CEL light came on. Shortly after my install I had the service engine soon light on... throwing code P0300... reset the and checked the MAFs and clamps... all good. The SES light came right back on. Anyone else have this issue?

I was noticing on the stillen website that the GIII's that are made for the G37 come with some sort of splash gaurds for the filters. I was wondering if the GII's for our Z's have it as well? Only reason I am asking is because the stillen website does not mention it coming with the intakes, I haven't seen anyone installing them on their Z's, and I thought the parts for the G37 and 370Z were interchangeable for the most part. I really want these but idk if I should due to the fact that water can get them. The gains are ridiculous and it just looks awesome when you open up the hood IMO. Any help is appreciated, thanks! :tiphat: