Lets get right down to business... SPL Parts Pro Rear Camber Arm Install DIY by DoubleDownMotorsports.com Estimated Install Time = 1-2 hours Difficulty = Easy Tools Needed: - Floor Jack
|
|
LinkBack | Thread Tools | Display Modes |
01-22-2009, 06:55 PM | #1 (permalink) |
The370Z.com Sponsor
|
DIY: SPL Parts Rear Camber Arms Install
Lets get right down to business...
SPL Parts Pro Rear Camber Arm Install DIY by DoubleDownMotorsports.com Estimated Install Time = 1-2 hours Difficulty = Easy Tools Needed: - Floor Jack - Jack Stands - Torque Wrench - Lug Wrench - Ratchet with 17mm and 14mm sockets - 17mm and 19mm wrenches - Phillips Head Screwdriver or Punch - 3/16 Allen Wrench - Adjustable Crescent Wrench - Rubber Mallet Step #1: Jack the rear of the car up until the rear tires are off the ground and you can slide jack stands underneath the frame rails. Once jack stands are in place, slowly lower the car onto the jack stands and remove jack from work space. Double check to ensure that the jackstands are properly placed and all four corners of the stands are firmly planted on the floor. I even like to give the car a nudge or two to make sure it doesn't move at all or fall off the stands before I get underneath it. Step #2: Remove the rear wheels by removing the lug nuts. This may not be necessary for the install but the extra room will sure make life easier. Set the wheels aside. Step #3: Locate the rear camber arm. Here is what they look like off the car... Step #4: Use the 17mm socket and wrench to remove the outer camber arm bolt (the one closest to the brakes). If necessary, use the rubber mallet on the end of the wrench to break the bolt loose. Once the nut has been removed, use the screwdriver or punch and rubber mallet to gently pound out the bolt. Step #5: Use the 14mm socket and loosen the sway bar bracket bolts. You do not need to remove the bolts completely, just loosen them enough to move the sway bar down a bit allowing the inner camber arm bolt to be removed in the next step. Step #6: Use the 17mm socket and 19mm wrench to remove the inner camber arm bolt. If necessary use the rubber mallet on the end of the wrench to break the bolt loose. Once the nut has been removed you should be able to wiggle the bolt out, above the sway bar that you lowered in step #5. Step #7: Remove the stock rear camber arm from the car. Step #8: Put the stock rear camber arm and SPL Parts Pro Rear Camber Arm next to eachother and adjust the lenght of the SPL arm until it is equal with the stock arm. Use the stock bolts and put them through the mounting holes of both arms to ensure that they are of equal length. Make sure everything is tight on the SPL arm before install. Step #9: Reverse the steps to install the SPL Parts Pro Rear Camber Arm. Step #10: Repeat Steps 1-9 for the other side of the car. Step #11: Re-install the wheels and tighten the lugs so the wheel sits flat and firm against the brake rotor hat. Step #12: Use the floor jack to raise the car up off of the jack stands and remove them from underneath the car. Slowly lower the car back down to the ground. Step #13: Use the torque wrench to torque the lugs back to factory specs (I torque mine to 80 lbs.) Step #14: Roll the car out of the driveway and back in to allow the suspension to settle. Step #15: Check your camber and toe to insure proper alignment. ***Note: If you do not have proper alignment measuring tools, it is highly recommended that you get to an alignment shop as soon as possible. Please do this install at your own risk. Double Down Motorsports does not hold any responsibility for problems that may occur due to installing these parts on your vehicle. As always, it is recommended to have a professional install these parts.
__________________
MikeBonanni.com Twitter: http://www.twitter.com/MikeBonanni Facebook: http://www.facebook.com/MBonanni36 Function > Form Last edited by M.Bonanni; 11-07-2010 at 12:16 AM. |
06-28-2010, 10:26 AM | #4 (permalink) |
The370Z.com Sponsor
|
The camber are completely separate from the toe bolt so no, but if you got SPC toe bolts along with it, you will need to enlarge the holes.
__________________
MikeBonanni.com Twitter: http://www.twitter.com/MikeBonanni Facebook: http://www.facebook.com/MBonanni36 Function > Form |
10-19-2010, 02:24 AM | #5 (permalink) |
A True Z Fanatic
Join Date: Apr 2010
Location: Ny
Posts: 1,391
Drives: 2k10Z34Pw
Rep Power: 17 |
If I was to go for spc rear camber arms do I have to do some MODS? Is it just straight up bolt on?
__________________
||F.I.CBE 18" CF muffler||Injen CAI||CF Bpillars||CF Stage 1 Side mirror||CS Amuse Kit||JquadHeadlights||3mTB35%Tint||Work Gnosis GS2|| Wish List==>||GTM TT||Coils||Camber Arms||Tires||Wing||Hotchkis Sways|| |
10-19-2010, 10:20 PM | #6 (permalink) |
The370Z.com Sponsor
|
They are just a straight bolt on replacement, no modification needed.
__________________
MikeBonanni.com Twitter: http://www.twitter.com/MikeBonanni Facebook: http://www.facebook.com/MBonanni36 Function > Form |
10-19-2010, 11:37 PM | #7 (permalink) |
A True Z Fanatic
Join Date: Apr 2010
Location: Ny
Posts: 1,391
Drives: 2k10Z34Pw
Rep Power: 17 |
thnx
__________________
||F.I.CBE 18" CF muffler||Injen CAI||CF Bpillars||CF Stage 1 Side mirror||CS Amuse Kit||JquadHeadlights||3mTB35%Tint||Work Gnosis GS2|| Wish List==>||GTM TT||Coils||Camber Arms||Tires||Wing||Hotchkis Sways|| |
11-06-2010, 08:36 AM | #8 (permalink) |
Track Member
Join Date: Mar 2009
Location: Lithia, FL
Age: 51
Posts: 552
Drives: 09 Nissan 370z CS M6
Rep Power: 186 |
Pics aren't coming through for me.. anyone else have that problem?
__________________
Dynojet 285 HP/245 TQ (pre CBE)// Agency Power CBE // GTM Test Pipes // JWT Pop Chargers // B&M Short Shifter // Eibach Springs // Powder-coated Akebono's // Powder-coated Strut Bar // Black Chromed 19" Rays // // Redline Designs Graphics TipsZ journal |
11-06-2010, 09:17 AM | #9 (permalink) |
A True Z Fanatic
Join Date: Apr 2010
Location: Ny
Posts: 1,391
Drives: 2k10Z34Pw
Rep Power: 17 |
He said he was going to re host it. can't see it either
__________________
||F.I.CBE 18" CF muffler||Injen CAI||CF Bpillars||CF Stage 1 Side mirror||CS Amuse Kit||JquadHeadlights||3mTB35%Tint||Work Gnosis GS2|| Wish List==>||GTM TT||Coils||Camber Arms||Tires||Wing||Hotchkis Sways|| |
11-07-2010, 12:17 AM | #10 (permalink) |
The370Z.com Sponsor
|
fixed
__________________
MikeBonanni.com Twitter: http://www.twitter.com/MikeBonanni Facebook: http://www.facebook.com/MBonanni36 Function > Form |
11-22-2010, 11:25 PM | #11 (permalink) |
A True Z Fanatic
Join Date: Apr 2010
Location: Ny
Posts: 1,391
Drives: 2k10Z34Pw
Rep Power: 17 |
THNX!!!! Great DIY
__________________
||F.I.CBE 18" CF muffler||Injen CAI||CF Bpillars||CF Stage 1 Side mirror||CS Amuse Kit||JquadHeadlights||3mTB35%Tint||Work Gnosis GS2|| Wish List==>||GTM TT||Coils||Camber Arms||Tires||Wing||Hotchkis Sways|| |
05-27-2011, 03:29 PM | #12 (permalink) |
Base Member
Join Date: Sep 2010
Location: Los Angeles
Posts: 110
Drives: MITSUBISHI EVO X
Rep Power: 15 |
where does the toe bolt go? i kno i have to enlarge the hole to fit the SPC toe bolt in. Precision Z in LA want to charge me $250 just to install the toe bolt due to the hole being small and have to be enlarged.
|
05-27-2011, 05:18 PM | #14 (permalink) | |
The370Z.com Sponsor
|
Quote:
__________________
MikeBonanni.com Twitter: http://www.twitter.com/MikeBonanni Facebook: http://www.facebook.com/MBonanni36 Function > Form |
|
Bookmarks |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
[FOR SALE] SPC rear CAMBER arms with Kinetix rear TRACTION / TOE arms | TVPostSound | Parts for sale (Private Classifieds) | 2 | 03-19-2013 09:54 PM |
Is there a DIY for front SPC Camber arms install? | TMAN1985 | Brakes & Suspension | 9 | 02-27-2012 04:23 AM |
DDM DIY - SPL Parts Rear Camber Arms Install | M.Bonanni | Brakes & Suspension | 7 | 10-04-2010 10:20 AM |