DIY: ** Rear 20mm stud replacement spacers

wheee! · 04-10-2010, 03:28 PM

OK!!! I know everyone wants to get the scoop on this so let's get started.

First of all, this is a VERY easy mod, no troubles what-so-ever!

I won't cover the basics like wheel or brake caliper removal as they're already covered in other DIY articles.

http://www.the370z.com/diy-section-d...ent-front.html

http://www.the370z.com/diy-section-d...r-install.html

Let's focus on the stud replacement!

1) Get a good set of wheel spacers and studs like these H&R 20mm's from Josh at Stillen

2) Remove the wheel and brake caliper and then remove the adjustment cover on your rotor. ** If your wheel rotates freely with the hand brake off, you do not need to adjust this star adjuster** If it does not move freely, back off the star adjuster a couple of clicks with a screwdriver to loosen the park brake. Count the clicks so you can reset it on re-assembly!

3) Remove the rotor and your rear brake assembly should look like this.

4) Remove the tensioning spring holding the brake shoes together.

5) Remove the star wheel assembly carefully, it is two pieces and will fall apart.

6) Screw on the M12 x 1.25 open ended lug nut and tap out the old studs.

This is a pic from the front rotor but same idea....

Slide new studs through from the rear and on a slight angle into the hub.

7) Tighten down the studs as you replace them. Use a bunch of washers and and open ended lug nut to pull them into seated position on the hub. M12 x 1.25 nut is required. Use an electric impact drill to seat them easily.

This picture is from the front assembly, but you get the idea!

8) Reinstall the star wheel and spring tensioner.

9) Replace the rotor and readjust the star wheel for proper tension. Add a layer of 'never-seize' to the back of the spacer and mount it on the rotor. Use two open ended nuts with washers to tighten the rotor into place. Replace the brake caliper.

10) Remount the wheel!!

That is it! No big deal at all.
Rep points appreciated if you found this helpful!

Finished shots:

m4a1mustang · 04-10-2010, 03:41 PM

Wow that looks super easy! I will be doing mine tomorrow.

+1 rep for the DIY!

wheee! · 04-10-2010, 03:44 PM

Glad you liked it! I had fun doing it and no hassles at all.

SoCal 370Z · 04-10-2010, 04:17 PM

Excellent write-up, rep point submitted!

Termac · 04-10-2010, 05:06 PM

Thanks exactly what I needed for my spacer job. +1 Rep points

ChrisSlicks · 04-10-2010, 05:29 PM

Nice write up. +rep

wheee! · 04-10-2010, 05:37 PM

Quote:

Originally Posted by Termac

Thanks exactly what I needed for my spacer job. +1 Rep points

Glad to help! I sweated over this mod for months before I got the parts in to actually do it. In the end it was no big deal! Feel free to down a pint of Fosters for me!!

Thanks for the rep points everyone!

ChrisSlicks · 04-10-2010, 05:41 PM

-rep for Fosters. Real Oz men don't drink that swill.

wheee! · 04-10-2010, 05:44 PM

Quote:

Originally Posted by ChrisSlicks

-rep for Fosters. Real Oz men don't drink that swill.

I used to love the stuff! But then again, it was the Canadian version brewed by Molsons.....

Paul_S · 04-10-2010, 06:21 PM

Great info

I might end up doing this myself and now I know what I need to do

schrute · 04-10-2010, 06:24 PM

Great DIY! +1 Rep

nogoodname · 04-10-2010, 07:20 PM

Those are the proper spacers.

Thanks for the write-up!

LinPark · 04-10-2010, 07:26 PM

Excellent write-up! +1 rep

Did you use an impact drill for this mod and if so which one do you have? Also, I'll go search for this in a minute but if you also did a write-up for the front spacers could you link to it from the first post or put a link in here somewhere for everyone?

Oh, and nice hammer - did Thor stop by to help with the install.

wheee! · 04-10-2010, 09:24 PM

Quote:

Originally Posted by LinPark

Excellent write-up! +1 rep

Did you use an impact drill for this mod and if so which one do you have? Also, I'll go search for this in a minute but if you also did a write-up for the front spacers could you link to it from the first post or put a link in here somewhere for everyone?

Oh, and nice hammer - did Thor stop by to help with the install.

I used a Cdn Tire "Maximum" cordless impact driver. 1/2" drive with a 21mm impact socket. The driver is 14.4v NiCD and did a great job as it is a maximum 102ft/lbs force. Went really quick.

As for the front spacers, it has been covered many times. Here is one link.

http://www.the370z.com/diy-section-d...r-install.html

The one difference I had was that you don't need to mod the shield to fit the bolts thru...

Go to my Mod Album to see all the pics for the front install.

As for the hammer... it is a 3lb sledge that is EXTREMELY handy to have around in tight spaces with limited throw. It packs a nice punch with one small swing! Thor would approve....

Modshack · 04-12-2010, 05:57 PM

Quote:

Originally Posted by schrute

Great DIY! +1 Rep

Yup!

04-10-2010, 03:28 PM	#1 (permalink)
wheee! A True Z Fanatic Join Date: Sep 2009 Location: Mod Capital of Canada Age: 57 Posts: 7,354 Drives: cars. lots of cars. Rep Power: 40182	DIY: Rear 20mm stud replacement spacers OK!!! I know everyone wants to get the scoop on this so let's get started. First of all, this is a VERY easy mod, no troubles what-so-ever! I won't cover the basics like wheel or brake caliper removal as they're already covered in other DIY articles. http://www.the370z.com/diy-section-d...ent-front.html http://www.the370z.com/diy-section-d...r-install.html Let's focus on the stud replacement! 1) Get a good set of wheel spacers and studs like these H&R 20mm's from Josh at Stillen 2) Remove the wheel and brake caliper and then remove the adjustment cover on your rotor. If your wheel rotates freely with the hand brake off, you do not need to adjust this star adjuster** If it does not move freely, back off the star adjuster a couple of clicks with a screwdriver to loosen the park brake. Count the clicks so you can reset it on re-assembly! 3) Remove the rotor and your rear brake assembly should look like this. 4) Remove the tensioning spring holding the brake shoes together. 5) Remove the star wheel assembly carefully, it is two pieces and will fall apart. 6) Screw on the M12 x 1.25 open ended lug nut and tap out the old studs. This is a pic from the front rotor but same idea.... Slide new studs through from the rear and on a slight angle into the hub. 7) Tighten down the studs as you replace them. Use a bunch of washers and and open ended lug nut to pull them into seated position on the hub. M12 x 1.25 nut is required. Use an electric impact drill to seat them easily. This picture is from the front assembly, but you get the idea! 8) Reinstall the star wheel and spring tensioner. 9) Replace the rotor and readjust the star wheel for proper tension. Add a layer of 'never-seize' to the back of the spacer and mount it on the rotor. Use two open ended nuts with washers to tighten the rotor into place. Replace the brake caliper. 10) Remount the wheel!! That is it! No big deal at all. Rep points appreciated if you found this helpful! Finished shots: Vampirex, AntiVenom, Gerg and 3 others like this. __________________ H&R / Stillen / Berk / HKS / Swift / Michelin / UpRev / SPC / Amuse Rep / Seibon / Fringe XVO / TWM / more... My Journal Last edited by wheee!; 01-29-2013 at 08:30 AM.

04-10-2010, 03:41 PM	#2 (permalink)
m4a1mustang A True Z Fanatic Join Date: Feb 2009 Location: Northern VA Posts: 55,385 Drives: on two wheels Rep Power: 6962	Wow that looks super easy! I will be doing mine tomorrow. +1 rep for the DIY! __________________ - Steve Zs & Coffee - Saturdays at 10AM in Fairfax, VA and Columbia, MD (Click the banner!) LIKE us on Facebook!

04-10-2010, 03:44 PM	#3 (permalink)
wheee! A True Z Fanatic Join Date: Sep 2009 Location: Mod Capital of Canada Age: 57 Posts: 7,354 Drives: cars. lots of cars. Rep Power: 40182	Glad you liked it! I had fun doing it and no hassles at all. __________________ H&R / Stillen / Berk / HKS / Swift / Michelin / UpRev / SPC / Amuse Rep / Seibon / Fringe XVO / TWM / more... My Journal

04-10-2010, 04:17 PM	#4 (permalink)
SoCal 370Z A True Z Fanatic Join Date: Feb 2009 Location: US of A Posts: 2,842 Drives: Answers Rep Power: 33	Excellent write-up, rep point submitted! __________________ ( Click to show/hide ) Why I NEVER say NO to the Panda Lou Fusz!!!

04-10-2010, 05:29 PM	#6 (permalink)
ChrisSlicks A True Z Fanatic Join Date: Mar 2009 Location: North East Posts: 6,203 Drives: 09 370Z Sport M6 Rep Power: 653	Nice write up. +rep __________________ Hotchkis ARB \| Stillen CAI \| Art Pipes \| Berk CBE \| Stillen AP Racing Brakes \| AE Performance Oil Cooler \| BC Racing ER Coilovers \| Doran Control Arms

04-10-2010, 05:06 PM	#5 (permalink)
Termac Base Member Join Date: Jan 2010 Location: Lake Macquarie Posts: 44 Drives: 2009 370z MB 7AT Rep Power: 15	Thanks exactly what I needed for my spacer job. +1 Rep points

04-10-2010, 05:41 PM	#8 (permalink)
ChrisSlicks A True Z Fanatic Join Date: Mar 2009 Location: North East Posts: 6,203 Drives: 09 370Z Sport M6 Rep Power: 653	-rep for Fosters. Real Oz men don't drink that swill. __________________ Hotchkis ARB \| Stillen CAI \| Art Pipes \| Berk CBE \| Stillen AP Racing Brakes \| AE Performance Oil Cooler \| BC Racing ER Coilovers \| Doran Control Arms

04-10-2010, 06:21 PM	#10 (permalink)
Paul_S Enthusiast Member Join Date: Sep 2009 Location: England Posts: 258 Drives: UK Yellow 370Z Rep Power: 16	Great info I might end up doing this myself and now I know what I need to do __________________ In the UK? Check out nissansportz.com - 350Z, GT-R, 370Z and more... 2004 Sunset 350Z to 2009 Limited Edition Ultimate Yellow 370Z

04-10-2010, 06:24 PM	#11 (permalink)
schrute Track Member Join Date: Aug 2009 Location: utah Posts: 781 Drives: my z every day Rep Power: 17	Great DIY! +1 Rep __________________ my journal \| 2009 370z touring \| 6mt \| platinum graphite \| my album second skin \| mr works \| fast intentions \| ssr \| eibach \| hotchkis \| spc \| toyo \| bluebatmobile \| v-led \| jwt \| ventureshield \| tinted tails

04-10-2010, 07:20 PM	#12 (permalink)
nogoodname Lifetime Premium Join Date: Nov 2008 Location: Montreal Posts: 22,357 Drives: E46 M3 Rep Power: 1765	Those are the proper spacers. Thanks for the write-up!

04-10-2010, 07:26 PM	#13 (permalink)
LinPark A True Z Fanatic Join Date: Jan 2010 Location: Columbus, OH Posts: 1,077 Drives: '17 Camaro 2SS A8 Rep Power: 23	Excellent write-up! +1 rep Did you use an impact drill for this mod and if so which one do you have? Also, I'll go search for this in a minute but if you also did a write-up for the front spacers could you link to it from the first post or put a link in here somewhere for everyone? Oh, and nice hammer - did Thor stop by to help with the install.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
H&R 20mm Stud-Replacement Front Spacer Install	Alstann	Wheels & Tires	8	03-03-2019 06:39 PM
[WTB] 20mm DRS spacers!! (stud replacement)	ts-c63	Parts for sale (Private Classifieds)	2	03-25-2013 11:47 PM
[FOR SALE] 20mm h&r built in stud spacers	memorylasts	Parts for sale (Private Classifieds)	5	02-27-2012 06:29 PM
LTT H&R 10mm Stud Replacement Spacers for 15mm stud replacement H&R	chuckd05	Parts for sale (Private Classifieds)	5	02-16-2011 06:05 PM
FS: Ichiba V1 Stud Replacement 20mm Wheel Spacers	toxik	Parts for sale (Private Classifieds)	9	01-19-2011 06:11 PM