DIY: ** Rear 20mm stud replacement spacers

wheee! · 09-18-2013, 08:26 AM

Quote:

Originally Posted by scruffydog

Has anyone here aside from Rusty have done a rear ARP stud replacement? I believe they're 28 mm and this method doesn't work as the new stud cannot be inserted behind the hub assembly. Any help would be great. I'm having trouble removing the rear hub due to the 17mm socket is interfering with the CV Joint drum.

Sorry, I have not seen the ARP studs. I know it is tight with the ones supplied in the 20mm kit so I would imagine the bearing hub would have to be removed for that....

Quote:

Originally Posted by SurfDog

subd. thanks!

Thanks and good luck!

Thorazine_IM · 12-05-2013, 07:01 PM

thinking about getting 5 mm spacers all around for my set up. my question is is it absolutely necessary to swap out to longer studs even with just 5 mm spacers? i dont track my car.

wheee! · 12-05-2013, 07:50 PM

I would think that five mm spacers would work with stock studs, but I may be wrong. It may also depend on the thickness of the wheel material between the lugnuts and the spacer as well. YMMV

Sent from Canadia

rjsf · 05-03-2014, 09:53 PM

Ok, total noob at modding here.

I tried to do this mod today, putting 20mm H&Rs on the rear. I started with my rear right wheel. I had no problems with the removal and all, but when I got to the point where I'm putting back the brake assembly, I got stuck - the brake pads came close, leaving only about a 2mm gap, not enough for the whole assembly to fit on the rotor again.

Has anyone run into this issue before, and how did you fix it? Anything I can do to have them move apart?

rjsf · 05-03-2014, 10:05 PM

Figured it out...

kornflake7 · 06-16-2014, 11:11 PM

Not sure what I'm doing wrong I did the fronts no problem and rear
Left no problem but the right rear after finally getting it all back together it sounds as though the pads are rubbing the inside of the rotor how do I adjust it so it's not rubbing anymore? I can't seem to get it lined up again?

wheee! · 06-17-2014, 08:15 AM

There is a star wheel adjuster that you can access thru the rear brake rotor. Remove the small rubber plug and then tighten the brake shoes up against the inner drum. When they are tight, THEN back them off about 3 or 4 clicks for freedom of movement.
Of course this is all done WITHOUT THE PARK BRAKE ENGAGED...

See step 2 in first post.

kornflake7 · 06-17-2014, 01:41 PM

Ok awesome will try when I get home thanks

AviatorTim · 10-15-2014, 06:37 PM

Quote:

Originally Posted by wheee!

4) Remove the tensioning spring holding the brake shoes together.

Are the small brake pads inside the rotor only used by the emergency brake?

wheee! · 10-15-2014, 07:01 PM

Yes.

12-05-2013, 07:50 PM	#213 (permalink)
wheee! A True Z Fanatic Join Date: Sep 2009 Location: Mod Capital of Canada Age: 57 Posts: 7,354 Drives: cars. lots of cars. Rep Power: 40182	I would think that five mm spacers would work with stock studs, but I may be wrong. It may also depend on the thickness of the wheel material between the lugnuts and the spacer as well. YMMV Sent from Canadia __________________ H&R / Stillen / Berk / HKS / Swift / Michelin / UpRev / SPC / Amuse Rep / Seibon / Fringe XVO / TWM / more... My Journal

05-03-2014, 09:53 PM	#214 (permalink)
rjsf Base Member Join Date: Jul 2010 Location: Torrance, CA Posts: 6 Drives: 09 Nissan 370Z MG A7 Rep Power: 15	Tried to do this today Ok, total noob at modding here. I tried to do this mod today, putting 20mm H&Rs on the rear. I started with my rear right wheel. I had no problems with the removal and all, but when I got to the point where I'm putting back the brake assembly, I got stuck - the brake pads came close, leaving only about a 2mm gap, not enough for the whole assembly to fit on the rotor again. Has anyone run into this issue before, and how did you fix it? Anything I can do to have them move apart?

05-03-2014, 10:05 PM	#215 (permalink)
rjsf Base Member Join Date: Jul 2010 Location: Torrance, CA Posts: 6 Drives: 09 Nissan 370Z MG A7 Rep Power: 15	Tried to do this today Figured it out... Last edited by rjsf; 05-12-2014 at 02:21 AM.

06-17-2014, 08:15 AM	#217 (permalink)
wheee! A True Z Fanatic Join Date: Sep 2009 Location: Mod Capital of Canada Age: 57 Posts: 7,354 Drives: cars. lots of cars. Rep Power: 40182	There is a star wheel adjuster that you can access thru the rear brake rotor. Remove the small rubber plug and then tighten the brake shoes up against the inner drum. When they are tight, THEN back them off about 3 or 4 clicks for freedom of movement. Of course this is all done WITHOUT THE PARK BRAKE ENGAGED... See step 2 in first post. __________________ H&R / Stillen / Berk / HKS / Swift / Michelin / UpRev / SPC / Amuse Rep / Seibon / Fringe XVO / TWM / more... My Journal Last edited by wheee!; 06-17-2014 at 08:17 AM.

10-15-2014, 07:01 PM	#220 (permalink)
wheee! A True Z Fanatic Join Date: Sep 2009 Location: Mod Capital of Canada Age: 57 Posts: 7,354 Drives: cars. lots of cars. Rep Power: 40182	Yes. __________________ H&R / Stillen / Berk / HKS / Swift / Michelin / UpRev / SPC / Amuse Rep / Seibon / Fringe XVO / TWM / more... My Journal

12-05-2013, 07:01 PM	#212 (permalink)
Thorazine_IM Base Member Join Date: Aug 2012 Location: CA Posts: 158 Drives: 13 Nissan 370Z PW M6 Rep Power: 13	thinking about getting 5 mm spacers all around for my set up. my question is is it absolutely necessary to swap out to longer studs even with just 5 mm spacers? i dont track my car.

06-16-2014, 11:11 PM	#216 (permalink)
kornflake7 Base Member Join Date: Mar 2014 Location: San Antonio, TX Posts: 233 Drives: 2013 Nismo 370z Rep Power: 11	Not sure what I'm doing wrong I did the fronts no problem and rear Left no problem but the right rear after finally getting it all back together it sounds as though the pads are rubbing the inside of the rotor how do I adjust it so it's not rubbing anymore? I can't seem to get it lined up again?

06-17-2014, 01:41 PM	#218 (permalink)
kornflake7 Base Member Join Date: Mar 2014 Location: San Antonio, TX Posts: 233 Drives: 2013 Nismo 370z Rep Power: 11	Ok awesome will try when I get home thanks

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
H&R 20mm Stud-Replacement Front Spacer Install	Alstann	Wheels & Tires	8	03-03-2019 06:39 PM
[WTB] 20mm DRS spacers!! (stud replacement)	ts-c63	Parts for sale (Private Classifieds)	2	03-25-2013 11:47 PM
[FOR SALE] 20mm h&r built in stud spacers	memorylasts	Parts for sale (Private Classifieds)	5	02-27-2012 06:29 PM
LTT H&R 10mm Stud Replacement Spacers for 15mm stud replacement H&R	chuckd05	Parts for sale (Private Classifieds)	5	02-16-2011 06:05 PM
FS: Ichiba V1 Stud Replacement 20mm Wheel Spacers	toxik	Parts for sale (Private Classifieds)	9	01-19-2011 06:11 PM