DIY: Adding In-Cabin air filter to the 370Z

raps101 · 05-30-2020, 07:13 PM

Can anyone post the best/most up to date instructions for removing the glove box and installing the in cabin air filter? I have the Nissan oem B7277-1ea0b in my possession.

Sent from my SM-G965U using Tapatalk

TreeSemdyZee · 05-30-2020, 08:14 PM

Instructions haven’t changed since the beginning of this thread.

millerdiller · 06-27-2022, 05:37 PM

So it has been a little frustrating for me, the screw #6; I hate that one, it has fallen somewhere in the back of the glovebox assembly and although I can hear the screw rattle, I cannot seem to be able to take it out, plus I am not sure if I have broken some of the screw holding structure (U-nuts?), I am wondering if I need to remove the electric cabling to get the screw out and if I need something else to put the screw back in, would a magnetic long screwdriver and some U nuts be enough to get this done?

BettyZ · 06-28-2022, 01:34 PM

Quote:

Originally Posted by millerdiller

So it has been a little frustrating for me, the screw #6; I hate that one, it has fallen somewhere in the back of the glovebox assembly and although I can hear the screw rattle, I cannot seem to be able to take it out, plus I am not sure if I have broken some of the screw holding structure (U-nuts?), I am wondering if I need to remove the electric cabling to get the screw out and if I need something else to put the screw back in, would a magnetic long screwdriver and some U nuts be enough to get this done?

You're going to need to take out the glovebox itself. Follow the FSM and you'll be fine.

millerdiller · 07-09-2022, 10:50 PM

@bettyz thanks a lot!
So, I was able to locate the "FSM" at https://www.nicoclub.com/archives/us...-database.html, assuming that is what you meant, I am unable to locate the specific document for the glovebox removal, searching online, it appears that I might just be able to disconnect the cables and get it fully out and then reconnect them after I get the lost screw from behind the assembly? What do you think?

BettyZ · 07-12-2022, 12:24 PM

Quote:

Originally Posted by millerdiller

@bettyz thanks a lot!
So, I was able to locate the "FSM" at https://www.nicoclub.com/archives/us...-database.html, assuming that is what you meant, I am unable to locate the specific document for the glovebox removal, searching online, it appears that I might just be able to disconnect the cables and get it fully out and then reconnect them after I get the lost screw from behind the assembly? What do you think?

That'd work for sure.

Alienpoker · 01-17-2025, 06:49 PM

Quote:

Originally Posted by g96818

First off, i would like to thank you for pioneering this DIY, but I hope you don't mind if i expand a little more and make corrections on your DIY.
Do this at your own risk, I'm not responsible if you break something using this easier modified directions.

The rest you can follow caneman88's to install/replace the filter. I just have one thing that I found might be useful and that is to cut 4 slots on the bottom of the filter wall so that you can close the vent door without smashing the filter. You'll know what i mean when you take off the vent door. Just line up the slots with the 4 things on the door and make like a 1/4" -> 1/2" cut. See pic for approx locations, measure the actual location with the vent door.

Yes the arrow on the filter points down. Air is sucked from the top and down into the circular thing.

I assume you guys know how to reverse the directions to put everything back.

Rep points much appreciated if you found this addition helpful

*edit* Fixed broken image. Let me know if the links are broken and I'll upload it again.

Well… I know this is an ‘old thread’, but please don’t cut any slits / slots in your air filter. The white plastic ramps serve a purpose. They push the filter up against where it seals as you close the access flap.

05-30-2020, 07:13 PM	#226 (permalink)
raps101 Base Member Join Date: Jun 2009 Location: New York Posts: 60 Drives: 09 Nissan 370z T/M6 Rep Power: 16	Can anyone post the best/most up to date instructions for removing the glove box and installing the in cabin air filter? I have the Nissan oem B7277-1ea0b in my possession. Sent from my SM-G965U using Tapatalk Last edited by raps101; 05-30-2020 at 07:15 PM.

05-30-2020, 08:14 PM	#227 (permalink)
TreeSemdyZee Premium Member Join Date: Dec 2009 Location: Kentuck-IANA Age: 60 Posts: 4,886 Drives: '09 370 & ‘14 Juke Rep Power: 27409	Instructions haven’t changed since the beginning of this thread. SouthArk370Z, Hubbabubba, Optimiser and 1 others like this. __________________ Borla S-Type \| Motordyne \| Z1 (lots) \| South Bend \| K&N \| Nismo/Nismo S-Tune \| Eibach \| Aerojacket \| Fujimara \| Spl \| ZSpeed Performance \| Kenwood-Infinity-Sound Ordnance \| Whiteline \| Ecutek \| Hotchkis \| Clazzio \| VQ Vortex \|Morimoto XB \|Dynosty Tune 329.64hp 265.73 ft/lb

07-09-2022, 10:50 PM	#230 (permalink)
millerdiller Base Member Join Date: Dec 2021 Location: San Jose Posts: 4 Drives: 2012-370z-White-Man Rep Power: 4	@bettyz thanks a lot! So, I was able to locate the "FSM" at https://www.nicoclub.com/archives/us...-database.html, assuming that is what you meant, I am unable to locate the specific document for the glovebox removal, searching online, it appears that I might just be able to disconnect the cables and get it fully out and then reconnect them after I get the lost screw from behind the assembly? What do you think? BettyZ likes this.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
No Cabin Filter on the 2009 370Z?	drisko	Nissan 370Z General Discussions	36	01-19-2023 03:26 AM
In Cabin Air Filter?	caneman88	Exterior & Interior	13	08-11-2012 11:50 AM
Cabin Filter	polarity	Nissan 370Z General Discussions	11	11-11-2009 12:24 AM
Confused Micro-Cabin Filter on 09's or just 2010?	Asheth	Nissan 370Z General Discussions	5	08-18-2009 11:00 PM
Cabin air filter	av370	Nissan 370Z General Discussions	3	07-17-2009 09:29 PM

06-27-2022, 05:37 PM	#228 (permalink)
millerdiller Base Member Join Date: Dec 2021 Location: San Jose Posts: 4 Drives: 2012-370z-White-Man Rep Power: 4	So it has been a little frustrating for me, the screw #6; I hate that one, it has fallen somewhere in the back of the glovebox assembly and although I can hear the screw rattle, I cannot seem to be able to take it out, plus I am not sure if I have broken some of the screw holding structure (U-nuts?), I am wondering if I need to remove the electric cabling to get the screw out and if I need something else to put the screw back in, would a magnetic long screwdriver and some U nuts be enough to get this done?