![]() |
*UPDATE* I finally decided to update this post with a video of the typical performance for HPDE's. Notice, no annoying clicking at all. http://www.youtube.com/watch?v=b_1TwBIgwKE So, I was running low on
|
![]() |
|
LinkBack | Thread Tools | Display Modes |
![]() |
#1 (permalink) |
A True Z Fanatic
|
![]()
*UPDATE*
I finally decided to update this post with a video of the typical performance for HPDE's. Notice, no annoying clicking at all. So, I was running low on funds for my HPDE, but I wanted to at least tape SOME of my sessions with my cheap point and shoot. Did a little searching, and decided to make my own in-car mount. Now, Im also using the base from my current Tripod, which makes things easy for me - you will need to customize this to suit you. First thing first, things I used: ![]() - 3' x 3/4" square tube ($10 or so) - 3x U-Bolts with the plates and nuts (all of which came together when you bought one...) - 6x locking washers for your U-bolts - 3/4" x ~4" bolt (not sure on the PRECISE length off hand) - 3/4" wing nuts (for the long bolt) - At least three 3/4" washers First, I went and measured dimensions for the actual posts. I was ORIGINALLY intending to have u-bolts wrapped around each headrest post, but it turns out that the distance between the 2 farthest posts is exactly 36" lol. So, I compromised, and decided to go with 2 posts on the passenger side, and 1 on the driver side. ![]() I started by cutting off ~2" worth of wooden dowel, and drilling a 3/4" hole through the center: ![]() I then started using painters tape and a pen to mark where the head rest posts were, and then using the u-bolts themselves, I marked where I'd need to put holes through the aluminum. ![]() Once done drilling all the holes for the u-bolts, I then turned the rod 90 degrees, and put a hole exactly halfway between the inside passenger side u-bolt holes, and the driver side u-bolt holes. ![]() Finally, I began assembling the important part - the mount. I slid one 3/4" washer over my long bolt, and put it through that center hole. Then, I put the dowel over that. I then put one more 3/4" washer at the top, with a wingnut to cap it off. I originally felt this would make for easy removal/installation of the mount, but sadly it looks like I'll need a wrench no matter what just to get it tight enough. Also, It turned out that the 3/4" dowel was slightly too small for my mount, and the 7/8" was too big...so I need to wedge something over the dowel that will make for a tight fit for the head. ![]() When all was said and done, you're left with this: ![]() Youtube sadly compressed the **** out of this video, gotta figure out how to fix that. Things I'm going to do to make it better: use those 3/4" wingnuts on the u-bolts themselves - that will make not only the bar much easier to remove, but easier to ensure its actually tight. Also, its getting a nice coat of paint here tomorrow, seeing as the sun was going down just as I finished it. Also, the video was a VERY dry run - I slapped it into the car as quick as possible before it got too dark. Lots of rattling, which I know the problem (base was hitting the wingnut on the dowel), and I know the actual base wasnt even tight on the dowel yet. Other than that, I made a perfectly good camera mount and it maybe cost me $25 total, including the $6 paint lol. Your results will vary if you dont have a mount that you could put onto a dowel - I'll leave that up to you to figure out, but an "easy" solution would be to simply put a bolt through the center hole the same size as needed for the camera. Only downside is, it'll be facing up in the air. I wanted adjust-ability.
__________________
I don't own a car anymore. Last edited by MightyBobo; 09-22-2010 at 09:32 PM. |
![]() |
![]() |
![]() |
#2 (permalink) |
Grand Prix of Endurance
![]() Join Date: Nov 2008
Location: Tennessee
Posts: 3,476
Drives: Mulsanne Straight
Rep Power: 26 ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() |
![]()
Very creative, well thought out!
![]()
__________________
![]() We can do without any article of luxury we have never had; but once obtained, it is not in human nature to surrender it voluntary. |
![]() |
![]() |
![]() |
#3 (permalink) |
A True Z Fanatic
Join Date: Jun 2009
Location: MD
Posts: 4,488
Drives: 09 Z34, 13 F-150
Rep Power: 26 ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() |
![]()
Necessity is the Mother of invention. Well done!
__________________
Jon Swift | SPC | Stillen | Motordyne | AAM | Cobb | Hawk | Volk Racing | Bridgestone
Green Demon Eyes |
![]() |
![]() |
![]() |
#5 (permalink) |
Base Member
Join Date: Oct 2009
Location: Denton, TX
Posts: 58
Drives: 2009/370z/TS/6MT
Rep Power: 16 ![]() |
![]()
Looks good. Gonna take that idea and run with it a bit. Thanks!
__________________
09 370Z - FI TDX CBE/Stillen G3/FI HFC's are next ![]() 06 Xterra OR - 3" SL - 33" Pro-Comp MT's - Shrockworks Sliders & Rear Bumper/Tire Carrier - Stillen Cross Drilled Rotors/Pads |
![]() |
![]() |
![]() |
#6 (permalink) |
Track Member
Join Date: Jan 2009
Location: Snoqualmie WA
Posts: 973
Drives: 03 996TT Porsche
Rep Power: 607 ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() |
![]()
Great idea and work! I'm going to do this idea too. I'm thinking some plastic dip on the u-bolts to minimize marring and vibration.
Thanks!
__________________
![]() Buddy Revell: "One man's sooner is another man's later" |
![]() |
![]() |
![]() |
#7 (permalink) |
A True Z Fanatic
|
![]()
Thanks, the mount worked fantastic at my TrackDaze event (as you saw from the carnage Im sure). There was absolutely no vibration noise once I tightened the bolts properly - my install for the test video in here was very temporary due to lack of time - sun was dropping fast!
Feel free to leave some rep if you make it and it works out ![]()
__________________
I don't own a car anymore. |
![]() |
![]() |
![]() |
#10 (permalink) | |
Administrator
Join Date: Sep 2008
Location: NJ
Posts: 9,930
Drives: 09 370Z MB Sports M6
Rep Power: 10 ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() |
![]() Quote:
![]()
__________________
The370Z Signature Pictures ll Want to rock our forum decals on your car? Then click here! ll How to Embed YouTube Videos In a Post STOP! (Hammertime) ll Become a Premium Member Click HERE ll F.A.Q. Are You a Nissan Dealer? Click Here to Become A "Supporting Dealer" and Start Listing Your 370Zs In Our Inventory Section My Monterey Blue Z ll My Exhaust --> ![]() ![]() Nissan's Official Response Regarding Oil Temp Issue: CLICK HERE Need a Set of Cheap Winter wheels /Tires? Then Visit The Banner Link Below and Place Your Order. You'll Help Keep The370Z Alive. ![]() |
|
![]() |
![]() |
![]() |
#11 (permalink) |
Base Member
Join Date: May 2009
Location: NYC
Posts: 5
Drives: 08 G37S 6MT
Rep Power: 16 ![]() |
![]()
wow Mad nice!
You sure that rattling isnt the U-bolts on the headrest posts? I was thinking you can get like a little rubber bushing to put on the posts to mount it around so you can eliminate the metal on metal contact.
__________________
STOOF@180|Custom ![]() |
![]() |
![]() |
![]() |
#12 (permalink) |
A True Z Fanatic
|
![]()
You guys are killing me lol.
OK, I'll say again - when I installed the mount for the example video above, the noise was mainly due to the fact that I did NOT tighten down the u-bolts enough, due to quickly fading daylight. Now, Im not saying that there isnt SOME rattle when I tighten them completely, but the VAST majority of the noises in the video are due to two things: 1) Loose u-bolts 2) Loose camera mount on the wooden dowel, so it was knocking against the wing nut at the top anytime I'd hit a bump. I will record another example when I pick the car up from the body shop on the way home.
__________________
I don't own a car anymore. |
![]() |
![]() |
![]() |
#13 (permalink) |
A True Z Fanatic
Join Date: Sep 2009
Location: Gold Coast CT
Posts: 10,599
Drives: 2019 Corvette G.S.
Rep Power: 43 ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() |
![]()
nice DIY, 2 snaps up!
![]() ![]()
__________________
SOLD MY Z MARCH 2018 - another Core OG moves on - new ride 2019 Z Corvette Grand Sport - no mods necessary but already have eyes on HFC and intakes LOL IT NEVER ENDS. |
![]() |
![]() |
![]() |
#15 (permalink) |
A True Z Fanatic
|
![]()
__________________
I don't own a car anymore. |
![]() |
![]() |
![]() |
Bookmarks |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Suggestions for camera mount. | houkouonchi | Audio & Video | 6 | 05-31-2012 10:36 PM |
DIY: Smartphone In Car Camera Mount | sixpax | DIY Section (Do-It-Yourself) | 0 | 04-14-2012 12:37 PM |
In-car Camera Mount Review | TongMan | Exterior & Interior | 10 | 04-12-2012 04:47 PM |
DIY Adjustable In-car Camera Mount | RedNismo | DIY Section (Do-It-Yourself) | 4 | 01-21-2011 02:36 PM |
Camera Mount Design | scruffydog | Exterior & Interior | 16 | 06-07-2010 09:01 PM |