QuickJack Lift System

synolimit · 03-03-2018, 07:38 PM

Mine has up issues. If you dont hold the button the whole time and feather it like to make sure youre making contact and all that, the system will lock out. You either 100% commit to the lift or it jams.

DeliriousClam · 03-03-2018, 08:39 PM

Quote:

Originally Posted by synolimit

Mine has up issues. If you dont hold the button the whole time and feather it like to make sure youre making contact and all that, the system will lock out. You either 100% commit to the lift or it jams.

I'm using all my will power to not make ED jokes

TreeSemdyZee · 03-03-2018, 09:20 PM

Quote:

Originally Posted by synolimit

Mine has up issues. If you dont hold the button the whole time and feather it like to make sure youre making contact and all that, the system will lock out. You either 100% commit to the lift or it jams.

That kind of sounds like bleeding issues.
Is it jumpy at all on the way up?

redrover23 · 03-04-2018, 02:34 AM

Quote:

Originally Posted by TreeSemdyZee

Are you sure the residual is in the power unit?
It might be in the hose.
Remember, there’s still fluid in the lines.
I’ve had a few times where I’ve had to push pretty hard, but finally got connected.

I'm pretty sure it's not the hoses. I was able to attach them to the lift rails with no problem.

What could be causing this problem on the down function? I'm thinking a failed solenoid valve but that's just a guess. Are there fuses to check? Thanks in advance.

TBatt · 03-09-2018, 11:00 AM

Quote:

Originally Posted by Jsolo

To the OP, how's the unit holding up? Any issues?

Working perfectly! Not a single issue.

One thing that I have learned is to hold the down button for about ten seconds AFTER the car has been lowered. This allows the pressure in the hoses to fully bleed off and it makes the hoses easier to remove and install. The quick couplers will hold pressure in the lines if you don't bleed them off and they can be a bear to install.

TBatt · 03-09-2018, 11:02 AM

Quote:

Originally Posted by redrover23

I'm pretty sure it's not the hoses. I was able to attach them to the lift rails with no problem.

What could be causing this problem on the down function? I'm thinking a failed solenoid valve but that's just a guess. Are there fuses to check? Thanks in advance.

Call Ranger. They will help you troubleshoot your problem.

l2iceman · 03-24-2018, 11:12 AM

Been looking into this, my Z is lowered on swift springs and I have the evo r sides. What is the height of these ramps when flat? I want to measure the side gear ancestry to see if I'd be able to slide it in sideways under my car.

CB1 · 03-24-2018, 11:30 AM

Quote:

Originally Posted by l2iceman

Been looking into this, my Z is lowered on swift springs and I have the evo r sides. What is the height of these ramps when flat? I want to measure the side gear ancestry to see if I'd be able to slide it in sideways under my car.

It depends on what model you are looking at getting.
Take a look at their measuring guide. It helped me. Also, feel free to call them. They were helpful over the phone too.
https://www.quickjack.com/quickjack-...ing-guide.html
I purchased the 7000-SLX and it works great for me. I also got the pinch weld blocks. I am at stock height.
They say you need a little clearance so that it can gain momentum to lift. I have an inch or two of clearance and mine lifts perfect.
This is right off of that page. "Keep in mind that there must be some space between QuickJack and your vehicle’s lifting points. If a collapsed QuickJack is pressed flush against your car, it will be unable to generate enough force to lift the vehicle."

Hope this helps..

l2iceman · 03-24-2018, 11:55 AM

Thanks for the advice! Costco in Canada has the Quickjack BL-5000SLX for a good price, so I'll look into those specs and clearance requirements.

Sent from my SM-N920W8 using Tapatalk

CB1 · 03-24-2018, 11:57 AM

Quote:

Originally Posted by l2iceman

Thanks for the advice! Costco in Canada has the Quickjack BL-5000SLX for a good price, so I'll look into those specs and clearance requirements.

Sent from my SM-N920W8 using Tapatalk

Good thing with Costco, you can return items if they don't work for you. At least in Washington state that's their policy.

TreeSemdyZee · 03-24-2018, 01:44 PM

Quote:

Originally Posted by l2iceman

Been looking into this, my Z is lowered on swift springs and I have the evo r sides. What is the height of these ramps when flat? I want to measure the side gear ancestry to see if I'd be able to slide it in sideways under my car.

3” to 3.6”

https://www.quickjack.com/#fullspecs

TreeSemdyZee · 12-20-2018, 07:55 PM

$150 discount code.

Quick150

CB1 · 12-20-2018, 07:58 PM

Loving mine...!

Felix 808 · 12-28-2018, 09:52 PM

My 5000SLX came today. Didn't take too long to set up. Seems like it's going to be pretty nice.

1st lift ( Daughters car)

cossie1600 · 01-15-2019, 02:44 AM

I have the racing tiles in my garage, can these guys go over it?

03-03-2018, 07:38 PM	#121 (permalink)
synolimit A True Z Fanatic Join Date: May 2013 Location: Columbus, OH Posts: 5,051 Drives: 2013 Silver 370z Rep Power: 3389	Mine has up issues. If you dont hold the button the whole time and feather it like to make sure youre making contact and all that, the system will lock out. You either 100% commit to the lift or it jams. __________________ 13 370z-

12-20-2018, 07:55 PM	#132 (permalink)
TreeSemdyZee Premium Member Join Date: Dec 2009 Location: Kentuck-IANA Age: 60 Posts: 4,885 Drives: '09 370 & ‘14 Juke Rep Power: 27408	Discount until 12/31/18 $150 discount code. Quick150 Felix 808 likes this. __________________ Borla S-Type \| Motordyne \| Z1 (lots) \| South Bend \| K&N \| Nismo/Nismo S-Tune \| Eibach \| Aerojacket \| Fujimara \| Spl \| ZSpeed Performance \| Kenwood-Infinity-Sound Ordnance \| Whiteline \| Ecutek \| Hotchkis \| Clazzio \| VQ Vortex \|Morimoto XB \|Dynosty Tune 329.64hp 265.73 ft/lb

12-20-2018, 07:58 PM	#133 (permalink)
CB1 Base Member Join Date: Jun 2011 Location: Washington Posts: 188 Drives: 2011 Touring/Sport Rep Power: 30	Loving mine...! Spartan 1771, TreeSemdyZee, 2011 Nismo#91 and 2 others like this. __________________ 2011 Metallic Black, Touring/Sport, Nav, AT \| F.I. Twin Turbo #060 \| E85 \| F.I. Built 7AT \| F.I. Flex Plate \| F.I. 34 Row Oil Cooler \| F.I. 19 Row 7AT Cooler \| ECUTEK Tuned By Sebastian \| 647 WHP 605 TQ \|

12-28-2018, 09:52 PM	#134 (permalink)
Felix 808 A True Z Fanatic Join Date: Oct 2011 Location: Camarillo, CA Posts: 1,063 Drives: 2011 PW/Grey T/S 7AT Rep Power: 2807	My 5000SLX came today. Didn't take too long to set up. Seems like it's going to be pretty nice. 1st lift ( Daughters car) CB1, madwi, wideglideleon and 3 others like this. __________________ Semper Fi Μολὼν λαβέ Last edited by Felix 808; 12-29-2018 at 06:34 PM. Reason: added picture

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
KW HLS (Hydraulic Lift System)	CLOUD10	Brakes & Suspension	45	02-09-2017 11:18 AM
Too low to lift car	laricb	Brakes & Suspension	18	01-07-2012 04:12 PM
Garage Lift System	maxtodorov	Nissan 370Z Warranty / Scheduled Maintenance / Servicing / Repairs	9	06-05-2010 07:26 PM

03-24-2018, 11:12 AM	#127 (permalink)
l2iceman Base Member Join Date: Oct 2014 Location: Toronto, Canada Posts: 126 Drives: '10 370z Rep Power: 240	Been looking into this, my Z is lowered on swift springs and I have the evo r sides. What is the height of these ramps when flat? I want to measure the side gear ancestry to see if I'd be able to slide it in sideways under my car.

03-24-2018, 11:55 AM	#129 (permalink)
l2iceman Base Member Join Date: Oct 2014 Location: Toronto, Canada Posts: 126 Drives: '10 370z Rep Power: 240	Thanks for the advice! Costco in Canada has the Quickjack BL-5000SLX for a good price, so I'll look into those specs and clearance requirements. Sent from my SM-N920W8 using Tapatalk

01-15-2019, 02:44 AM	#135 (permalink)
cossie1600 A True Z Fanatic Join Date: Jun 2009 Location: californee way Posts: 5,380 Drives: 370, Leaf Rep Power: 30	I have the racing tiles in my garage, can these guys go over it?