Nissan 370Z Forum  

REQUEST:Changing front and rear brake pads on stock akebono

Originally Posted by Mike those should work spear, where do you get them? Home Depot. Nice little rubber caps, easy to adjust and slowly screw tighter, and super cheap...hopefully they

Go Back   Nissan 370Z Forum > Nissan 370Z Tech Area > DIY Section (Do-It-Yourself)


Like Tree1Likes

Reply
 
LinkBack Thread Tools Display Modes
Old 02-21-2010, 09:04 PM   #46 (permalink)
A True Z Fanatic
 
spearfish25's Avatar
 
Join Date: Mar 2009
Location: Naples, FL
Posts: 4,117
Drives: to work
Rep Power: 1856
spearfish25 has a reputation beyond reputespearfish25 has a reputation beyond reputespearfish25 has a reputation beyond reputespearfish25 has a reputation beyond reputespearfish25 has a reputation beyond reputespearfish25 has a reputation beyond reputespearfish25 has a reputation beyond reputespearfish25 has a reputation beyond reputespearfish25 has a reputation beyond reputespearfish25 has a reputation beyond reputespearfish25 has a reputation beyond repute
Send a message via AIM to spearfish25
Default

Quote:
Originally Posted by Mike View Post
those should work spear, where do you get them?
Home Depot. Nice little rubber caps, easy to adjust and slowly screw tighter, and super cheap...hopefully they do the trick.
__________________
2013 Cadillac V-Wagon, RIP Z

Last edited by spearfish25; 02-21-2010 at 11:18 PM.
spearfish25 is offline   Reply With Quote
Old 12-08-2010, 08:28 AM   #47 (permalink)
A True Z Fanatic
 
flashburn's Avatar
 
Join Date: May 2009
Location: Central Florida
Posts: 1,884
Drives: '12 Corvette GS 6M
Rep Power: 19
flashburn is just really niceflashburn is just really niceflashburn is just really niceflashburn is just really niceflashburn is just really nice
Default

So I'm going to be doing this today, but I just had a question.

If I do it one pad at a time, do I just do the following:
1. Remove pins.
2. Push/Pull one of the pads towards the pistons.
3. Remove that pad.
4. Apply brake grease between shim and pad.
5. Slide in new pad.

Only reason I'm a bit confused is the DIY link included shows them pulling out each pad, and then putting them back in sideways? Is that necessary, or can you just remove them and then put in the new pad?
__________________
Current Ride: 2012 Chevrolet Corvette Grand Sport Centennial Edition Carbon Flash 6M
Previous Ride: 2009 Nissan 370Z Sport Platinum Graphite 7AT
flashburn is offline   Reply With Quote
Old 12-08-2010, 04:11 PM   #48 (permalink)
A True Z Fanatic
 
spearfish25's Avatar
 
Join Date: Mar 2009
Location: Naples, FL
Posts: 4,117
Drives: to work
Rep Power: 1856
spearfish25 has a reputation beyond reputespearfish25 has a reputation beyond reputespearfish25 has a reputation beyond reputespearfish25 has a reputation beyond reputespearfish25 has a reputation beyond reputespearfish25 has a reputation beyond reputespearfish25 has a reputation beyond reputespearfish25 has a reputation beyond reputespearfish25 has a reputation beyond reputespearfish25 has a reputation beyond reputespearfish25 has a reputation beyond repute
Send a message via AIM to spearfish25
Default

The reinserting the pad sideways is to push the pistons back in to give you room. You'll need some extra space when you're inserting new pads when replacing old pads.

The steps are:
1. remove wheel
2. turn wheel to side you're working on (optional but helpful and easiest if front end is completely on jack stands)
3. pull out cotter pin (one in each retaining pin)
4. Use screw driver to push retaining pin out a bit while pressing on the tensioner plate with your other hand (the pin runs across the tensioner plate...you'll see what I mean). Once the pin is pushed out a bit, you can grab the inside with needle nose pliers and pull it out. Repeat for second pin. The tensioner plate will come off...save it to reinstall later.
5. using your fingers, pull on one pad with even, generous force to pull it away from the rotor and compress the pistons on that side. You just need a little movement to remove the pad.
6. Once the pad is out, reinsert it sideways and make sure it's covering both pistons if you're working on the front calipers. Use it as a gentle pry bar to pry the pistons further into the caliper. This will allow you to install the new, thicker pad. Be careful and slow and you won't chip the pad you're prying with. In time, you can just use an old worn out pad for this step.
7. Slide in your new pad that has been greased on the side edges and back. You can be generous with the grease.
8. Repeat steps 5-7 on the opposite pad in that caliper.
*don't remove both pads at once and then try to pry the pistons. You'll just push the pistons out on the other side as you pry the opposite side into the caliper. If you're doing the front caliper, you have to push the pair of pistons evenly or one will go in while the other comes out.
9. With both pads swapped, replace the tensioner plate over the pads and slide the retainer pins back in place. Just take your time and it will all line up. If the pins won't go in, try removing and replacing the pads or swapping them (sometimes they're happier on one side than the other, though they look identical).
10. With the pins in place, replace the cotter pins.
11. Repeat for the remaining calipers.
12. Turn the ignition to 'on' or start the engine. Depress the brake pedal repeatedly until it firms up. Check your brake fluid level to make sure it's still at the Max line. Below Max will get you Slip and VDC lights. Over Max will get you an overflow spill potentially.

Enjoy the pads.
Smashley likes this.
__________________
2013 Cadillac V-Wagon, RIP Z
spearfish25 is offline   Reply With Quote
Old 12-08-2010, 06:13 PM   #49 (permalink)
A True Z Fanatic
 
flashburn's Avatar
 
Join Date: May 2009
Location: Central Florida
Posts: 1,884
Drives: '12 Corvette GS 6M
Rep Power: 19
flashburn is just really niceflashburn is just really niceflashburn is just really niceflashburn is just really niceflashburn is just really nice
Default

Thanks a lot spearfish! It was way easier than I expected it to be, which figures, haha. Most difficult thing for me was lining up the cotter pins on the rear caliper's, couldn't see so well.

Glad everyone mentioned to keep an eye on the brake fluid, I had to suck out a good amount, and if I didn't notice it would of overflowed.
__________________
Current Ride: 2012 Chevrolet Corvette Grand Sport Centennial Edition Carbon Flash 6M
Previous Ride: 2009 Nissan 370Z Sport Platinum Graphite 7AT
flashburn is offline   Reply With Quote
Old 12-08-2010, 10:23 PM   #50 (permalink)
The370Z.com Sponsor
 
Mike's Avatar
 
Join Date: Jun 2009
Location: Loganville, GA
Posts: 5,944
Drives: 370z
Rep Power: 2186
Mike has a reputation beyond reputeMike has a reputation beyond reputeMike has a reputation beyond reputeMike has a reputation beyond reputeMike has a reputation beyond reputeMike has a reputation beyond reputeMike has a reputation beyond reputeMike has a reputation beyond reputeMike has a reputation beyond reputeMike has a reputation beyond reputeMike has a reputation beyond repute
Default

pretty much it, but I take two flat blade screwdrivers and use them to push the pistons back in while the old pads are still on the car, since it won't matter if they are damaged a little. Insert the screwdrivers between the pad and rotor, one on each side and use leverage to push the pistons back in.
__________________
NISSAN: 75 280Z / 86 300ZX GLL /87 Sentra SE / 03 350Z / 23 Z
Porsche: 93 968 / 23 Macan GTS / 93 968
Mike is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Nissan Akebono 14" Brake Kits, Hawk Pads, Stoptech Rotors, 370Z Sport Coz@Czp Suspension/Brakes 68 06-01-2018 12:23 PM
WTB: Front Akebono Calipers djosephm Parts for sale (Private Classifieds) 5 07-22-2009 05:36 PM
Which Brake Pads? prodigyz Brakes & Suspension 11 05-07-2009 11:41 AM


All times are GMT -5. The time now is 03:21 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO 3.6.0 PL2