Problems with swift lowering spring install

N0SL3N · 03-24-2014, 12:57 PM

I used some DIY instructions on here and they were pretty thorough

Pnoyz916 · 03-24-2014, 01:01 PM

I used diy from here . Not bike honda s2k

Sh0velMan · 03-24-2014, 01:37 PM

You can't do springs on this car with one side of the car still on the ground. The sway bars will make it very difficult to get it all back together and make it very dangerous to boot. Link me to this DIY that advises you to do what you are doing so that I can get it deleted.

Chuck33079 · 03-24-2014, 01:39 PM

Quote:

Originally Posted by Sh0velMan

You can't do springs on this car with one side of the car still on the ground. The sway bars will make it very difficult to get it all back together and make it very dangerous to boot. Link me to this DIY that advises you to do what you are doing so that I can get it deleted.

Yep. Plus, a S2K has the same style front suspension, doesn't it? So the "only jack up one side" method would be just as much of a fail as it is here?

BrandonSS · 03-24-2014, 02:32 PM

Quote:

Originally Posted by Chuck33079

This issue you're having isn't brand specific.

You can stop being a **** to the newb... he doesnt know where the proper jack point is in the front so yes, this is brand specific.

Newb, look under the car beyond the oil pan and belly pan. There is a flat surface surface that is connected to the front suspension and unibody, that is an appropriate jack point. It's hard to reach (nearly impossible) especially after being lowered.

Chuck33079 · 03-24-2014, 02:35 PM

Quote:

Originally Posted by BrandonSS

You can stop being a **** to the newb... he doesnt know where the proper jack point is in the front so yes, this is brand specific.

The need to have the whole front end off the ground isn't brand specific, not the jack points.

BrandonSS · 03-24-2014, 02:42 PM

I'm not going to argue but I have changed suspension on my gtp back in 1999'ish without lifting the entire front. Why? I was 18 with only 1 jack stand. Did I get it installed and is it still driving to this day, yup. Is it easier when lifting the entire front end? Of course.

There are nicer ways of responding to those lacking the know how regardless of how they claim to know things.

Chuck33079 · 03-24-2014, 02:44 PM

Quote:

Originally Posted by BrandonSS

I'm not going to argue but I have changed suspension on my gtp back in 1999'ish without lifting the entire front. Why? I was 18 with only 1 jack stand. Did I get it installed and is it still driving to this day, yup. Is it easier when lifting the entire front end? Of course.

There are nicer ways of responding to those lacking the know how regardless of how they claim to know things.

Did it work? Sure. Was it safe? **** no.

kenchan · 03-24-2014, 02:50 PM

Sh0velMan · 03-24-2014, 02:57 PM

So dudebro was nice enough to post a pic without indicating the proper lifting points, allow me to supply this helpfully annotated image.

The points that PWJDM used to lift the car are probably 'okay' and probably the only place they could reach without ******* up that nismo's body work (since they probably don't have lift adapters to clear the skirts), but they are not the Nissan-approved lifting points.

I have circled the Nissan-approved lift/side jacking points in green and circled the Nissan-approved 'shop jacking' points in blue. The front is a "nipple" or "bump" that sticks out in the front, the rear is the differential carrier.

Jack the front first with the parking brake set, transmission in gear and wheel chocks in place. Then lift the rear after the front is securely on jack stands placed at the Nissan-approved side jacking points (green circles) as far forward as possible. Place your rear jack stands at the rear side jacking points (green circles) as far rearward as possible.

Reverse the process to lower.

synolimit · 03-24-2014, 03:23 PM

Quote:

Originally Posted by Sh0velMan

You can't do springs on this car with one side of the car still on the ground. The sway bars will make it very difficult to get it all back together and make it very dangerous to boot. Link me to this DIY that advises you to do what you are doing so that I can get it deleted.

Even with both in the air I couldn't pull them out or in. It cockeyed the long *** bolt that goes through everything with how the endlink bolts to the sway. It takes literally 20 seconds a side to undo the link off the sway. That way the long bolt can go in without issue. It still needs off the ground to pull the lower.

synolimit · 03-24-2014, 03:28 PM

Quote:

Originally Posted by Sh0velMan

So dudebro was nice enough to post a pic without indicating the proper lifting points, allow me to supply this helpfully annotated image.

The points that PWJDM used to lift the car are probably 'okay' and probably the only place they could reach without ******* up that nismo's body work (since they probably don't have lift adapters to clear the skirts), but they are not the Nissan-approved lifting points.

I have circled the Nissan-approved lift/side jacking points in green and circled the Nissan-approved 'shop jacking' points in blue. The front is a "nipple" or "bump" that sticks out in the front, the rear is the differential carrier.

Jack the front first with the parking brake set, transmission in gear and wheel chocks in place. Then lift the rear after the front is securely on jack stands placed at the Nissan-approved side jacking points (green circles) as far forward as possible. Place your rear jack stands at the rear side jacking points (green circles) as far rearward as possible.

Reverse the process to lower.

If you look really close at that pic though the black rubber pads are correct though.

Super Werty · 03-24-2014, 07:38 PM

Quote:

Originally Posted by Sh0velMan

You can't do springs on this car with one side of the car still on the ground. The sway bars will make it very difficult to get it all back together and make it very dangerous to boot. Link me to this DIY that advises you to do what you are doing so that I can get it deleted.

I did it. I had to disconnect the front sway and lifted and installed one side at a time.

Sh0velMan · 03-24-2014, 09:23 PM

Quote:

Originally Posted by Super Werty

I did it. I had to disconnect the front sway and lifted and installed one side at a time.

Yes, that's one way to get around the sway bar issue.

b15 · 03-24-2014, 11:19 PM

Lots of mistakes made by the OP here. I hope he's at least using jack stands...

After you raise the front end, make sure the top hat is aligned correctly or the lower holes still wont line up. I learned the hard way and had to recompress both sides and rotate the top hat slightly

03-24-2014, 12:57 PM	#31 (permalink)
N0SL3N Enthusiast Member Join Date: Dec 2011 Location: Toronto Posts: 376 Drives: 2009 PG 370z 6MT Rep Power: 35	I used some DIY instructions on here and they were pretty thorough __________________ \| Akuma \| Motordyne \| Z1 \| NST \| CNT \| Stillen \| Avant Garde \| RJM \| Performix \| Tint \| LED \| GTR \| Nissan \|

03-24-2014, 01:37 PM	#33 (permalink)
Sh0velMan A True Z Fanatic Join Date: Jan 2012 Location: Dallas/Ft.Worth Posts: 3,349 Drives: Noisily. Rep Power: 20	You can't do springs on this car with one side of the car still on the ground. The sway bars will make it very difficult to get it all back together and make it very dangerous to boot. Link me to this DIY that advises you to do what you are doing so that I can get it deleted. Chuck33079 likes this. __________________ Buy My Car! \| Build Thread

03-24-2014, 02:42 PM	#37 (permalink)
BrandonSS Track Member Join Date: Apr 2013 Location: Indianapolis Age: 43 Posts: 644 Drives: 2009 370z T/S/techM6 Rep Power: 13	I'm not going to argue but I have changed suspension on my gtp back in 1999'ish without lifting the entire front. Why? I was 18 with only 1 jack stand. Did I get it installed and is it still driving to this day, yup. Is it easier when lifting the entire front end? Of course. There are nicer ways of responding to those lacking the know how regardless of how they claim to know things. sandersd likes this.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
DIY: 370Z Lowering Spring Install	TypeOne	DIY Section (Do-It-Yourself)	158	02-18-2021 12:13 PM
ARK GT-F Lowering Spring	lauj	Brakes & Suspension	2	02-19-2014 06:34 PM
Swift Spring install question	fl350z	Brakes & Suspension	25	09-29-2013 01:20 PM
here are my alignment specs after swift spring install	area3z	Brakes & Suspension	5	03-28-2012 08:24 AM

03-24-2014, 01:01 PM	#32 (permalink)
Pnoyz916 Base Member Join Date: Feb 2014 Location: California Posts: 182 Drives: 13 370z Sport PW Rep Power: 11	I used diy from here . Not bike honda s2k

03-24-2014, 02:50 PM	#39 (permalink)
kenchan A True Z Fanatic Join Date: Aug 2009 Location: N/A Posts: 76,801 Drives: N/A Rep Power: 141521

03-24-2014, 11:19 PM	#45 (permalink)
b15 A True Z Fanatic Join Date: Feb 2010 Location: Chicago Posts: 3,229 Drives: 4drz Rep Power: 36571	Lots of mistakes made by the OP here. I hope he's at least using jack stands... After you raise the front end, make sure the top hat is aligned correctly or the lower holes still wont line up. I learned the hard way and had to recompress both sides and rotate the top hat slightly