SPL rear titanium mid links, springs???

gomer_110 · 02-12-2016, 10:22 PM

Quote:

Originally Posted by synolimit

I think that's a prob then. A 7" spring at oem heights probably putting it at an odd angle. You saw my pics and gomers, 6" spring with adjuster at half way and straight when compressed. You need to slam it or go 6".

My springs are 7" free length.

DEpointfive0 · 02-12-2016, 10:32 PM

Quote:

Originally Posted by synolimit

Well since I DIDNT f*^k the guy who clames I did who I sold my links to cause they were perfect on my car, maybe yours are 350z's? Even though I doubt that's an issue because I gave away my oem buckets to a 350z guy and he has no issue. So idk

Whathuh?

And SPL said they're the same and that I have the newest revision

OldFart · 02-21-2016, 04:25 PM

Really late to this one, but I called them on the same issue about the spring alignment. They said it was normal when car was jacked up, when car is down on ground it looks ok from what I can see. I'm running a 6" spring and my adjuster is in the middle, have plenty of room to go either way. Total bitch adjusting them though - the spring binds on tbe inside of the adjuster.

When the weather gets nice I have to play with my droop, any major bump I hit it sounds like I am slamming up against something with the suspension, but not seeing anything amiss.

Here is a picture of mine with the car on the ground.

Spooler · 02-21-2016, 10:22 PM

I was looking at these but man they seem to be a pain to get right.

OldFart · 02-21-2016, 10:57 PM

Quote:

Originally Posted by Spooler

I was looking at these but man they seem to be a pain to get right.

There is some trial and error. I just backed the car up on race ramps and have enough room to make adjustments without removing anything. Take it out for a spin and measure. It is a nice setup.

Spooler · 02-21-2016, 11:04 PM

Any benefits besides getting rid of the toe bolt cheesy crap?

OldFart · 02-21-2016, 11:16 PM

Quote:

Originally Posted by Spooler

Any benefits besides getting rid of the toe bolt cheesy crap?

For a daily driver, probably not, except for the adjustibility - and the chubby ya might get when under the car. What you have listed in your post is almost my exact setup. I can never leave well enough alone, hense my reasoning for doing it.

gomer_110 · 02-21-2016, 11:17 PM

Quote:

Originally Posted by Spooler

Any benefits besides getting rid of the toe bolt cheesy crap?

Addressed a couple of pages back.

Quote:

Originally Posted by gomer_110

Suspension geometry doesn't change from stock. The advantages are that you can use more readily available 2.5" ID springs, adjust ride height (could help handling), and can adjust camber and toe with a more robust adjustment than just toe bolts.

OldFart · 02-21-2016, 11:20 PM

Quote:

Originally Posted by Spooler

Any benefits besides getting rid of the toe bolt cheesy crap?

For a daily driver, probably not, except for the adjustibility - and the chubby ya might get when under the car. What you have listed in your post is almost my exact setup. I can never leave well enough alone, hense my reasoning for doing it.

This was prior to putting the mid links on.

clkio · 04-20-2016, 08:52 PM

Bringing this back. Anybody has more info on this? I bought the mid links and I am running coil overs but I need the 2.5 springs to get them to fit. However, I am still not too sure about height (whether to go with 6 or 7") and what spring rate? Thank you

clkio · 04-21-2016, 07:51 AM

I found tein springs at my buddy's shop that were 7" long and 2.5 in diameter. They fit perfect however I don't know what the spring rate is on them. I will contact SPL and neomotorsports (coilover manufacturer) and see what I can come up with

OptionZero · 07-27-2016, 06:11 PM

Bumping this thread. I too am experiencing the popping noise when going on ramps

Setup:
Aragosta coilovers w/ pillowball mounts
SPL arms in back: midlink, camber, traction arms
6 inch Swift spring.

Reading the responses above, it appears that adjusting the rear coilover height/length to keep pre-load on teh spring may solve the issue. The Aragosta rears are adjustable, so i'll be playing with that.

DEpointfive0 · 07-27-2016, 09:12 PM

Quote:

Originally Posted by OptionZero

Bumping this thread. I too am experiencing the popping noise when going on ramps

Setup:
Aragosta coilovers w/ pillowball mounts
SPL arms in back: midlink, camber, traction arms
6 inch Swift spring.

Reading the responses above, it appears that adjusting the rear coilover height/length to keep pre-load on teh spring may solve the issue. The Aragosta rears are adjustable, so i'll be playing with that.

There is no rear preload...

You need to fix your droop most likely

2SIC4U · 03-10-2017, 11:33 AM

Quote:

Originally Posted by synolimit

I'm worried about something if someone can help...

I installed the spl mid links and the 6" swift 10kg springs. The car is at a ride height of 26 3/16th on both sides. I don't remember where the car sat before the install with the swift spec-r's. I know it was 26 something, I think high 26. The spl mid link is about half way to get to that height and where spl said it should be.

The issue is if I jack the car up the spring almost falls out of the bucket. If this happened it'd be a total crash or worse! So basically I have zero preload if that's what you call it. I've seen Z's on three wheels before so there is a chance the spring could pop out on a track. Not to mention the loud banging all the time as the spring pops in and out over big holes all the time beating up the upper and lower buckets.

What do I do? Buy an adjustable length shock?

Almost popping out, only one side jacked up.

You need a helper spring Swift Helper Springs to keep a load on the spring. KW provided me this information as I ran into your same issue Swift Helper Springs H65-070-008. Also you need to find a better alignment shop or if you did this yourself, you need to correctly adjust the top (there is a bolt you can adjust) to move the top spring so when the car is on the ground, the spring still stays straight up and down...vs the way yours is now at a weird angle.

2SIC4U · 03-10-2017, 11:52 AM

Update:

KW Variant 3 Coil-overs
Hotchkis 370z front sway bar
SPL PRO Front Upper Camber/Caster Arms
SPL PRO Front End Links Spherical
SPL Eccentric lockout kit

SPL TITANIUM Rear Mid Links
SPL TITANIUM Rear Camber Arms
Swift Springs 65mm 5inch 10k
Swift Helper Springs H65-070-008

For those that posted issues with a popping noise or noise when going over bumps. Your issue is you do not have the required helper springs so when you hit a pot hole, bump, or your tire comes off the group, there is no pressure holding your rear springs in the midlink so it's the spring moving...this can be dangerous and your rear spring could come out under the right conditions. My car now drives like it's on rails and is an amazing ride. I have it at the perfect height, no more wheel gap, not slammed, and I can come up an inch or down 2 more inches using the midlink cup.

02-21-2016, 04:25 PM	#63 (permalink)
OldFart Track Member Join Date: May 2013 Location: Carlisle, PA Age: 61 Posts: 682 Drives: 2011 Wannabe Nismo Rep Power: 960	Really late to this one, but I called them on the same issue about the spring alignment. They said it was normal when car was jacked up, when car is down on ground it looks ok from what I can see. I'm running a 6" spring and my adjuster is in the middle, have plenty of room to go either way. Total bitch adjusting them though - the spring binds on tbe inside of the adjuster. When the weather gets nice I have to play with my droop, any major bump I hit it sounds like I am slamming up against something with the suspension, but not seeing anything amiss. Here is a picture of mine with the car on the ground. Last edited by OldFart; 02-21-2016 at 04:40 PM.

02-21-2016, 10:22 PM	#64 (permalink)
Spooler A True Z Fanatic Join Date: Jun 2014 Location: Ga Posts: 13,801 Drives: 2013 Nismo 370z Rep Power: 2684392	I was looking at these but man they seem to be a pain to get right. Hotrodz likes this.

03-10-2017, 11:52 AM	#75 (permalink)
2SIC4U Base Member Join Date: Oct 2012 Location: Germantown, MD Age: 45 Posts: 33 Drives: 2010 Nissan 370Z R Rep Power: 27	Update: KW Variant 3 Coil-overs Hotchkis 370z front sway bar SPL PRO Front Upper Camber/Caster Arms SPL PRO Front End Links Spherical SPL Eccentric lockout kit SPL TITANIUM Rear Mid Links SPL TITANIUM Rear Camber Arms Swift Springs 65mm 5inch 10k Swift Helper Springs H65-070-008 For those that posted issues with a popping noise or noise when going over bumps. Your issue is you do not have the required helper springs so when you hit a pot hole, bump, or your tire comes off the group, there is no pressure holding your rear springs in the midlink so it's the spring moving...this can be dangerous and your rear spring could come out under the right conditions. My car now drives like it's on rails and is an amazing ride. I have it at the perfect height, no more wheel gap, not slammed, and I can come up an inch or down 2 more inches using the midlink cup. Last edited by 2SIC4U; 04-05-2017 at 11:12 AM.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[FOR SALE] NIB Whiteline Rear End Links - NJ	PharmDZ	Parts for sale (Private Classifieds)	3	10-19-2013 10:13 AM
SPL TITANIUM Rear Toe Links IN STOCK READY TO SHIP! No wait!	SE	Suspension/Brakes	3	08-09-2013 02:18 PM
Rear camber links?	tommyguns	Brakes & Suspension	20	06-21-2013 10:05 PM
Rear clunking sound after sway bars and rear links	pty370z	Brakes & Suspension	3	05-19-2013 01:24 PM
[FOR SALE] SPL Rear Camber Links, SPL Rear Traction Links--Brand New in Box!	daleks	Parts for sale (Private Classifieds)	6	09-05-2011 06:22 PM

02-21-2016, 11:04 PM	#66 (permalink)
Spooler A True Z Fanatic Join Date: Jun 2014 Location: Ga Posts: 13,801 Drives: 2013 Nismo 370z Rep Power: 2684392	Any benefits besides getting rid of the toe bolt cheesy crap?

04-20-2016, 08:52 PM	#70 (permalink)
clkio Enthusiast Member Join Date: May 2014 Location: Cambridge ON Posts: 265 Drives: 09 370z M6 Rep Power: 11	Bringing this back. Anybody has more info on this? I bought the mid links and I am running coil overs but I need the 2.5 springs to get them to fit. However, I am still not too sure about height (whether to go with 6 or 7") and what spring rate? Thank you

04-21-2016, 07:51 AM	#71 (permalink)
clkio Enthusiast Member Join Date: May 2014 Location: Cambridge ON Posts: 265 Drives: 09 370z M6 Rep Power: 11	I found tein springs at my buddy's shop that were 7" long and 2.5 in diameter. They fit perfect however I don't know what the spring rate is on them. I will contact SPL and neomotorsports (coilover manufacturer) and see what I can come up with

07-27-2016, 06:11 PM	#72 (permalink)
OptionZero A True Z Fanatic Join Date: Apr 2011 Location: Sacramento Posts: 3,228 Drives: 15 370Z Nismo 6MT Rep Power: 214100	Bumping this thread. I too am experiencing the popping noise when going on ramps Setup: Aragosta coilovers w/ pillowball mounts SPL arms in back: midlink, camber, traction arms 6 inch Swift spring. Reading the responses above, it appears that adjusting the rear coilover height/length to keep pre-load on teh spring may solve the issue. The Aragosta rears are adjustable, so i'll be playing with that.